Fit the new timing belt, starting at the crankshaft pulley and working up towards the top of the engine, finishing off at the camshaft pulley. Tension the timing belt tensioner, making sure you align the pointer to the notch, and torque the nut.
Full Answer
How do you install a timing belt tensioner?
21:3738:46How to Replace Timing Belt Tensioner and Pulleys 06-09 Subaru OutbackYouTubeStart of suggested clipEnd of suggested clipThere's a threaded hole. It's kind of hard to see it's up into here spread this tensioner in by handMoreThere's a threaded hole. It's kind of hard to see it's up into here spread this tensioner in by hand. Get it started so this is correct now without that pin interfering.
How do you remove a timing belt tensioner?
Loosen the middle tensioner cog in the middle of the timing configuration; it's smaller than the two cams and will have a bolt on it. As you're loosening the bolt, push down on the spring and move it downwards. Then, tighten the bolt to lock it in place. This will loosen the timing belt, allowing you to remove it.
How much does it cost to change a VW timing belt?
Belts themselves aren't that expensive. The real cost is in the labor, because a lot of parts need to be disassembled to get to the belt. Shopping around to get a few quotes is your best bet to get the best deal, but you can expect to pay anywhere from $409 to $919 (including parts and labor).
When should you change the timing belt on a VW Golf?
We recommend changing your cambelt once every four years for cars registered before September 2009, and every five years for cars registered after. If you reach the recommended mileage limit before 4 or 5 years, you may need to change the cambelt sooner. For more information, contact your local retailer.
How does a timing belt tensioner work?
The base holds the other parts, and the spring keeps the belt pulled tight. The pulley is what facilitates movement of the belt. The tensioner arm is found on the bottom of the tensioner, and if you press on it, it will work against the spring, delivering enough slack so that you can adjust or remove the belt.
How do I know if my timing belt tensioner is bad?
When a timing belt tensioner fails, it can result in a number of different symptoms.Symptom 1: Squealing, rattling, or chirping. ... Symptom 2: Knocking or slapping. ... Symptom 3: Check engine light illuminated. ... Materials Needed.Step 1: Park your vehicle and turn off the engine.More items...•
How do you tell if timing is off on an engine?
2:124:21How To Tell If Your Engine Timing Is Off - YouTubeYouTubeStart of suggested clipEnd of suggested clipLight is producing your check engine light is producing. And if it pulls a timing code then you knowMoreLight is producing your check engine light is producing. And if it pulls a timing code then you know your timing is off or there's a problem with the timing.
Will a broken timing belt destroy my engine?
As your vehicle gets older and accumulates miles, its timing belt wears out and becomes compromised. While timing belt replacement is a simple service to perform, if a worn out timing belt snaps, it can seriously damage your engine and cost you thousands.
Is it worth fixing a timing belt?
Although timing belts are critical, there's no need to replace them regularly –unless explicitly recommended in your owner's manual. Some automakers recommend changing a timing belt between 60,000 and 100,000, others don't. Many of today's timing belts can go 100,000 miles or more without needing to be replaced.
How do I check my timing belt?
To inspect the belt, first look at the outside of the belt to see if any tiny cracks are forming. The timing belt is a very strong metal-reinforced belt with rubber on the outside. The rubber should be fairly smooth, with no chunks missing or massive cracking.
How do you know if timing belt needs to be replaced?
5 Common Signs Your Timing Belt Needs To Be ReplacedEngine Makes a Ticking Noise. When the timing belt starts to wear out, it may create a ticking sound inside the motor. ... Engine Won't Turn Over. ... Engine Misfires. ... Rough Idling of the Engine. ... Decline in Oil Pressure and Oil Leaking.
How long will a cracked timing belt last?
60,000 to 100,000 milesIn most cases, the need for a timing belt replacement will not be made clear until it breaks. As a general rule of thumb, mechanics recommend replacing it every 60,000 to 100,000 miles. You also can look in your owner's manual to verify manufacturer recommendations as well.
How to replace timing belt tensioner?
Refill the cooling system with the correct coolant. Ensure the timing belt area is clean and dry, before replacing the idlers and torqueing to the manufacturer’s specification. Fit the new timing belt tensioner (this may be a slightly different design to the original one) and the new nut, but do not tighten. Rotate the camshaft and high pressure fuel pump pulleys fully clockwise on their elongated holes, ensuring the pulleys are free to rotate but not tip.
How to fit a timing belt?
Fit the new timing belt, starting at the crankshaft pulley and working up towards the top of the engine, finishing off at the camshaft pulley. Tension the timing belt tensioner, making sure you align the pointer to the notch, and torque the nut. Using the pulley counter hold tool, pull on the camshaft pulley in an anti-clockwise direction, keeping the timing belt under tension. Now tighten the camshaft and high pressure fuel pump pulley bolts and torque to the manufacturer’s specification.
Where is the timing mark on a crankshaft?
Rotate the engine and align the timing marks; the crankshaft timing mark is a line on the crankshaft timing belt pulley that aligns with the pointer on the locking tool (see Fig 2) and the locking tool pin locates in a socket.
How to support an engine?
Support the engine by means of a beam or an under vehicle support (see Fig 5), and remove the engine mounting assembly.
When replacing a timing belt, what temperature should the engine be?
When replacing a timing belt, the engine needs to be at an ambient temperature to ensure the correct tension is achieved. Always rotate the engine in the normal direction of rotation (unless otherwise advised) and it is recommended that all the tensioners, idlers and fixings are replaced and torqued as per the manufacturer’s instruction.
How often should I replace a Volkswagen Golf 1.6?
Although the car we’ve featured in this tutorial wasn’t due a replacement based on its mileage, it is four years old and the manufacturer recommends a replacement every four years ...
Can you change timing belts on a bonnet?
When initially opening the bonnet, the timing belt system may look a little tricky to change, but with a little know-how and the appropriate tools it will prove to be an ideal repair for an independent garage.