how to wire golf cart key switch with lights

How to Wire Lights to a Golf Cart: Step-by-Step Instructions

• Step 1. Mount the Lights Disconnect the chassis black wire from the negative battery terminal on your golf cart. Then,...
• Step 2. Mount the Toggle Switch Mount the toggle switch for the lights on the driver's side of the dash. Drill a 1/2...
• Step 3. Connect the Electrical Connect one of the leads of the inline...

Full Answer

Where can I get a wiring diagram for my golf cart?

Golf Car Catalog can provide customized wiring diagrams specific to your cart, and specific accessory upon request. Just e-mail ([email protected]) or call (800-328-1953).

How do you wire a 12 volt battery for a golf car?

All gas golf cars draw power from a 12 volt battery for the ignition system to start the car. With this type of system, you wire directly to the battery for the 12VDC source. Typical installation will have the ground lead wired directly from the accessory to the 12 volt battery (negative terminal).

How do you wire a toggle switch headlight switch?

Extend the lead to the center terminal of the toggle switch. Use an insulated female spade terminal to connect the lead to the switch. Get a 16-gauge wire. Run it from the toggle switch at the second terminal all the way to the headlights. Use a solderless butt connector to connect the wire to the headlights. Secure the wires with nylon wire ties.

What power do I need for my golf cart electrical accessories?

Most electrical accessories in the golf car industry are powered via a 12VDC source. There are some exceptions with headlights as we offer some 36VDC and 48VDC versions. Providing a suitable 12VDC source for your golf cart electrical accessories will depend on several things.

What color wires go to ignition switch?

The colors of the wires that go to the ignition switch are red, black, white-Red, and white black.

How do you wire a keyed ignition switch?

0:115:42HOW TO WIRE IGNITION KEY + STARTER SWITCH SIM ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipCut off the for metal terminals and strip the ends of the wires. Join the two white wires andMoreCut off the for metal terminals and strip the ends of the wires. Join the two white wires and install a ring terminal to the ends of the wires using a crimping tool.

How does a golf cart key switch work?

The ignition switch on a golf cart is crucial for getting the vehicle started and operating as smoothly as possible. It pulls electricity from the battery and sends a charge to the engine that gets your cart running.

How do you bypass the ignition switch on a golf cart?

The Starting ProcessTurn off the ignition switch to minimize your risk of electrocution. ... Locate the wires for your cart's ignition switch. ... Use wire snips to cut these wires away from their connectors. ... Touch the engines together carefully to bypass the ignition switch and send power to your engine.More items...

How do you rewire an ignition switch?

2:023:50How to Rewire Power Through Ignition Switch in Your Car - YouTubeYouTubeStart of suggested clipEnd of suggested clipEnd you push in the new wire. Until it stops and then the old wire in the car just pushes right intoMoreEnd you push in the new wire. Until it stops and then the old wire in the car just pushes right into the slot. Then you just get a big pair of pliers and squeeze the metal that clamps it together ah.

How does a 4 wire ignition switch work?

A ground or grounded at the unit mount is what the 4 wire ign key has. One needs to turn on the electrical and the other needs to unground the coil. The coil wire is grounds when you turn off the key.

How do you start a Club Car golf cart without a key?

Quick Screwdriver Method:Insert the tip of your screwdriver in the ignition switch's slot.Move the screwdriver up and down gently but firmly until you can turn the tool around the same way you would turn a key.This should fire up the cart. ... Another method would be hot-wiring which involves working the wires.

Are golf cart keys universal?

A key will not work on all golf carts. Instead, they are limited to the vehicles manufactured by that company. For example, if you lost the keys to your E-Z-Go TXT Elite, you would not be able to use a Clubcar cart key. Therefore, in most cases, golf cart keys are universal relative to the manufacturer.

How does golf cart Ignition work?

As it spins, it sends this electrical charge directly to the ignitor on your cart. Once your ignitor is hit by this charge, it boosts the signal to make it stronger. The idea here is to make the charge strong enough to ignite the gasoline in your cart's engine as it runs.

How do you bypass an ignition switch without the key?

Take your screwdriver and insert it into the ignition lock cylinder. Turn it as far round in a clockwise direction that you can. Then pull the paperclip to the right as much as you can. You should then be able to slide the switch out easily.

How do I turn my ignition switch on without the key?

In order to start it without a key, one needs to bypass the ignition lock which should only be done when you lost your key. It can only be done by connecting ignition cord to the battery cord followed by touching the starter cord to the connection.

How do you bypass an ignition relay?

2:254:39cts no crank how to bypass starter relay - YouTubeYouTubeStart of suggested clipEnd of suggested clipSystem basically the computer will send the signal from here to there to let um to let the car uhMoreSystem basically the computer will send the signal from here to there to let um to let the car uh start so it'll energize a little coil inside this relay.

How many batteries does a golf cart have?

Go to the battery and disconnect the negative terminal. A golf cart can have up to six batteries, so disconnect the negative terminal from each of the batteries. The batteries can be found under the front seat.

Can you replace lights on a golf cart?

Replacing lights in a golf cart can be easy with the right tools. It's easy to replace or add lights to a golf cart. This technique can be used for any golf cart, whether it is powered by gas or electricity. Before beginning, gather all of your tools and materials in one spot that you can easily reach.

Beginning Steps

The first thing you should do before installing a new light kit on your golf cart is to unplug the original source. You must unplug the negative terminal connected to the battery to ensure safety. Once everything’s been unplugged, think about where you want to place the headlights on your cart.

Final Points

The final tip for how to wire golf cart lights is to secure everything. Place the correct wires in the hole you drilled earlier. Then, grab some tape to secure every wire. Finally, plug in the negative terminal and flip the toggle switch to see if the lights turn on. If headlights beam the path in front of you, you’re golden.

Types of Golf Cart Electrical Accessories

Golf cart electrical accessories may include, but certainly are not limited to, gauges (gas, hour meters, speedometers, volt meters, and charge indicators), lights (head, tail, brake, strobe, spot, security, fog, decorative holiday, marker and turn signal lights), cigarette lighters, power outlets, fans, horns, various switches (light, horn, turn signal, and key), and voltage reducers..

Typical Installation of Golf Cart Electrical Accessories

Most electrical accessories in the golf car industry are powered via a 12VDC source. There are some exceptions with headlights as we offer some 36VDC and 48VDC versions. Providing a suitable 12VDC source for your golf cart electrical accessories will depend on several things.

Gas Golf Cart Electrical Accessories Installation

First, let’s address providing a suitable 12VDC source for golf cart electrical accessories in a gasoline powered golf cart. All gas golf cars draw power from a 12 volt battery for the ignition system to start the car. With this type of system, you wire directly to the battery for the 12VDC source.

36 Volt Golf Cart Electrical Accessories Installation

Installing electrical accessories into a 36 volt golf car provides a bit more of a challenge. Mostly, since the battery bank does not provide 12V already as in the gas installation above. Luckily, 36V systems generally use six 6 volt batteries and six is a divisor of twelve.

48 Volt Golf Cart Electrical Accessories Installation

Installation of 12 volt accessories into a 48 volt system presents its own unique problem. These 48 volt systems typically use six 8 volt deep cycle batteries in series to provide the 48 volts.

Can a key switch be tested with a multimeter?

You should be able to test the key switch and verify with your digital multimeter. The multi meter should work fine on the battery pack with the charger plugged in a running. If you burned the negative probe of the meter it must have been touching something else along with the battery terminal.

Does the EZGO 2 have power to both terminals?

If I'm not mistaken the EZGO 2 terminal key switch only has power to both terminals when the key is on and the golf cart is in forward or reverse.