How to Wire Golf Cart Lights
- Disconnect the negative battery terminal.
- Mount the headlights as high on the cart as possible for best visibility. ...
- Determine the best place to mount the toggle switch that will control your lights. The left side of the dash is a common place for it.
- Drill a hole to mount the switch. Generally this will be a 1/2-inch hole, but check your switch to be sure the threaded portion will go through a ...
- Connect one lead of the inline fuse holder to the positive terminal of the battery with a solderless ring terminal.
- Use a butt connector and extend the other lead of the inline fuse holder to the center terminal of the toggle switch.
- Run a 16-gauge wire from the second terminal of the toggle switch to the headlights. Connect it to the headlights using solderless butt connectors.
- Tape over all connections with electrical tape and secure all wiring with nylon wire ties.
- Mount the toggle switch in the hole you drilled earlier.
- Reconnect the negative battery terminal. Turn the toggle switch to the "on" position to test your lights.
How do I Mount headlights on a golf cart?
Mount the headlights as high on the cart as possible for best visibility. Mounting brackets that simply clamp around a round structure, such as a bumper or roll bar, make this task simple.
How to wire golf cart lights?
How to Wire Golf Cart Lights Step 1. Disconnect the negative battery terminal. Step 2. Mount the headlights as high on the cart as possible for best visibility. Mounting brackets that simply clamp... Step 3. Determine the best place to mount the toggle switch that will control your lights. The left ...
How do you wire a toggle switch to a headlight switch?
Run a 16-gauge wire from the second terminal of the toggle switch to the headlights. Connect it to the headlights using solderless butt connectors. Tape over all connections with electrical tape and secure all wiring with nylon wire ties.
How do you mount a light switch on a bumper?
Mounting brackets that simply clamp around a round structure, such as a bumper or roll bar, make this task simple. Determine the best place to mount the toggle switch that will control your lights. The left side of the dash is a common place for it. Drill a hole to mount the switch.
How do you wire 12 volt lights on a 36 volt golf cart?
2:0714:30By from two to six volt batteries that's a consecutive order to give me 12 volts I have the hot wireMoreBy from two to six volt batteries that's a consecutive order to give me 12 volts I have the hot wire wired in at the main positive lead then get to the negative terminal.
How do you install golf cart headlights?
How to Change Golf Cart HeadlightsPark your golf cart where you can sit comfortably in front of it. ... Remove the screws that hold the headlight lens in place. ... Detach the wiring clips from the back of the headlamp. ... Reinstall the light and the headlight lens. ... Remove the lens cover from the headlight.More items...
How do you wire 12 volt lights to a 48 volt golf cart?
0:061:09Negative goes to your negative side and these your black and yellow will be your positive andMoreNegative goes to your negative side and these your black and yellow will be your positive and negative going out to your lights. Or. Whatever else you're trying to power at 12 volts.
How do you put the headlights on a EZ Go golf cart?
0:1611:36We have taped our template up along the ridges in the front cow. Once you're happy with yourMoreWe have taped our template up along the ridges in the front cow. Once you're happy with your template. We're going to mark the inside with a marking pin.
How do you wire lights on a Yamaha golf cart?
3:558:17Light in a long end goes to the passenger side tail light we want to do feed the long end over yourMoreLight in a long end goes to the passenger side tail light we want to do feed the long end over your passenger tire wheel. And connect that to your rear taillight.
How do you put lights on a Club Car golf cart?
0:166:30Today we're installing a mad jacks light kit designed for a club car precedent included in the kitMoreToday we're installing a mad jacks light kit designed for a club car precedent included in the kit is the headlight and bumper to taillights a main wiring harness including a switch.
Does my golf cart need a voltage reducer?
If your Golf Cart is Gas, you will not need a voltage reducer. However, if you have an electric golf cart the LEDGlow Voltage Reducer is required. This Voltage Reducer will take any 15-60 volt system and reduce it down to the 12 volt 5 amp required to power the lighting kit.
Can you use 4 12-volt batteries in a 48 volt golf cart?
For example, a typical 48-volt golf car may use eight 6-volt batteries, six 8-volt batteries, or four 12-volt batteries.
How do you wire golf cart accessories?
0:416:16And you can find fuse boxes that have six to eight different fusible links. They're super easy toMoreAnd you can find fuse boxes that have six to eight different fusible links. They're super easy to wire you have a positive coming in you have negative coming in. So it's a pretty easy setup.
How do I fix the lights on my EZ Go golf cart?
How to Fix EZGO RXV headlights not workingFirst, check all the wires used to establish a circuit connection.Check if the wires are torn or not connected properly.Use the DVOM to check the amount of power going to the fuse.If there is no power, then the fuse is blown.More items...
How do you put lights on a gas golf cart?
0:275:31The most important thing to remember about this install is to find a stable mounting location forMoreThe most important thing to remember about this install is to find a stable mounting location for each tube that ensures none of the lead power wires get caught in any moving.
How do you install a voltage reducer on a golf cart?
0:553:33Clean the mounting location. And the reducer with an alcohol prep. Pad. Use double-sided adhesive toMoreClean the mounting location. And the reducer with an alcohol prep. Pad. Use double-sided adhesive to mount the reducer to the location you just clean. The voltage reducer has two sets of wires.
Beginning Steps
The first thing you should do before installing a new light kit on your golf cart is to unplug the original source. You must unplug the negative terminal connected to the battery to ensure safety. Once everything’s been unplugged, think about where you want to place the headlights on your cart.
Final Points
The final tip for how to wire golf cart lights is to secure everything. Place the correct wires in the hole you drilled earlier. Then, grab some tape to secure every wire. Finally, plug in the negative terminal and flip the toggle switch to see if the lights turn on. If headlights beam the path in front of you, you’re golden.
How to test if your lights are working?
Test your lights by flipping the toggle switch back and forth. If your lights work, you’ve successfully set them up. If not, check your work again to identify the issue.
Where should I mount my headlights on my golf cart?
Mount the headlights as high as possible on the golf cart using the mounting brackets. It’s best to mount the headlights either on the front bumper or rollbar on the top of your vehicle.