Removing length from the butt end of the shaft also removes weight from that end and changes the swing weight and balance of the club. Cutting a shaft from one end or the other also changes the kickpoint of the shaft–lowering it if you cut from the butt end or raising it if you cut from the tip.
How do you shorten a golf club shaft?
With steel shafts, use a tubing cutter to trim the shaft; with graphite shafts, shorten using a hacksaw. Re-install a grip on the newly shortened shaft. And, most importantly, Wishon says, add weight to the clubhead in some manner to restore the swingweight feel of the club.
Why do golfers cut down shafts and reinstall them?
But some do-it-yourself golfers also cut down golf shafts, then reinstall them in their clubs. They do this to make their clubs better fit their swing, which might mean cutting the shaft simply to change length, or to change swingweight, flex or other playing characteristics.
Should I shorten or lengthen my club?
The advantage of shortening the club (over lengthening it) is that if the feel isn't ideal, then the process of 'correcting' it is pretty simple! Lead tape can be used initially, then the change can be made 'permanent' with Tungsten powder down the shaft jammed in with a cork. Thanks again Foxholer!
What does taper mean in golf shafts?
All golf shafts taper; that is, their circumference is greater at the grip end than at the tip end. That means that the grip end is the strongest part of the shaft and the tip end the weakest, which, Wishon says, leads trimming to have different effects:
Can golf club shafts be shortened?
With steel shafts, use a tubing cutter to trim the shaft; with graphite shafts, shorten using a hacksaw. Re-install a grip on the newly shortened shaft. And, most importantly, Wishon says, add weight to the clubhead in some manner to restore the swingweight feel of the club.
Can you shorten a golf driver shaft?
Shortening the shaft will make the club shorter but it will also make the shaft stiffer and adjust the swing weight as well. Plus, the more length you remove, the less flex your club will have. Depending on how much you cut it down, it could move a regular flex to a stiff or a stiff to an extra stiff.
How can I shorten my golf clubs at home?
Cut down one side of the old grip with a utility knife. Roll back the edges to peel the grip away from the tape on the club shaft. If the tape is still sticky, use a solvent to break down the adhesive as you pull up on the grip. Use your utility knife to scrape off the layer of tape.
Does shortening a golf club make it stiffer?
A shorter shaft is typically stiffer than a longer one. Although a shorter golf club shaft tends to be firmer than a longer one, it is important to understand the changes trimming a shaft will make to a club before making such a permanent change.
What happens if driver shaft is too long?
“If a driver shaft is too long for the player, they can struggle to find the middle consistently. Off-centre hits not only drastically reduce ball speed and distance, but have a big impact on accuracy.”
How much can you cut off a driver shaft?
Any amount of cutting will slightly stiffen the club. It will probably go unnoticed if you take 1 inch or less off the club. Taking 2 inches off will change the flex of the club. If you are shortening irons, every 1 inch you shorten the club will make the iron effectively play 2 degrees flatter.
Can you adjust golf club length?
To avoid cutting the shaft or adding an attachment, purchase a new shaft at your desired length. Cut the ferrule and remove the clubhead from the old shaft as you did before trimming the tip. If you wish to keep the original grip, use an air compressor to separate it from the old shaft, then pull the grip off.
How much does it cost to shorten golf clubs?
How much does it cost to shorten golf clubs? On average, it will cost $3-5 per club plus the cost of a new grip to shorten your clubs. If you're looking to save your old grips, you won't have to pay for new grips, but you'll have to pay a save grip fee of around $10 per club.
Can I cut my irons to one length?
Every ONE Length iron has been re-engineered to match 7-iron head weight, therefore, any custom shaft (cut to 7-iron length) can work with any of the ONE Length heads.
What happens when you butt trim a shaft?
1:363:54How Does Butt Trimming a Golf Shaft Affect Playability? - YouTubeYouTubeStart of suggested clipEnd of suggested clipChange when cutting one inch or less or or more off of the butt end probably. The biggest downsideMoreChange when cutting one inch or less or or more off of the butt end probably. The biggest downside of cutting. Or making a closed shoulder is the effect that it has on swing weight.
How much does it cost to shorten a driver shaft?
Generally, this fee will be about $15 to $35 depending on where and when you get the work done. Replacing a shaft on a driver is a bit more work than regripping a club.
How long should your driver be based on height?
Tony Finau is one of the tallest golfers on the PGA Tour at 6'4″, and his driver's length is usually around 45 inches. Both Finau and Fowler are two of the longest drivers on the PGA Tour....Driver Shaft Length Based Solely on Height.Height (feet/inches)Driver Shaft Length5'0″-5'2″44.5″4'10”-5'0″44″< 4'10”43″7 more rows•May 9, 2021
How much does it cost to shorten a driver shaft?
Generally, this fee will be about $15 to $35 depending on where and when you get the work done. Replacing a shaft on a driver is a bit more work than regripping a club.
Should I shorten the length of my driver?
When fitting a driver, it's important to get loft, lie, shaft, and grip sorted, but better driving may be hiding in a shorter shaft. In fact, a shorter shaft should help you find the sweet spot more often and may even add distance.
How long should your driver be based on height?
Tony Finau is one of the tallest golfers on the PGA Tour at 6'4″, and his driver's length is usually around 45 inches. Both Finau and Fowler are two of the longest drivers on the PGA Tour....Driver Shaft Length Based Solely on Height.Height (feet/inches)Driver Shaft Length5'0″-5'2″44.5″4'10”-5'0″44″< 4'10”43″7 more rows•May 9, 2021
How do you cut down a driver shaft?
1:144:01How to Cut Golf Shaft DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo for the first step you have to remove your old grip. I find the easiest way to do this is toMoreSo for the first step you have to remove your old grip. I find the easiest way to do this is to literally just cut a line all the way down your club.
How to measure for a new grip on a golf club?
That will tell you how much tape you need to apply to the shaft in order to get maximum adhesion without having any extra sticking out of the bottom of the grip. Once you know how much tape you’ll need on the shaft, measure the shaft, and make a mark a little short of the full length of the grip.
What to do when cutting a golf club down?
The first thing that you need to do when you’re cutting a club down is to get the old grip out of your way. In order to do that safely, you need to have plenty of space to work in and a way to hold the club steady while you’re cutting. That’s where the prepared workspace and the vice come in.
How to get adhesive off of golf club?
Heating the tape up will soften the adhesive and make this step easier. Heat the adhesive with a heat gun or a hairdryer. Peel the tape off until you have removed it all from the shaft of the club.
What tape do you use to secure a golf grip?
Adhesive Tape (for securing the new grip – purchase from a pro shop) (the amount you’ll need depends on how many clubs you’re planning on cutting down)
What happens if you cut too much off a golf club?
If you cut too much off of a club, you’ll be making the shaft a lot more rigid. You’ll also be getting into a skinnier section of the shaft, and that might affect the possibility of finding a grip that will fit appropriately. You don’t want to find out that you took too much by watching your club fly out of the grip on the follow-through of the first shot that you hit with it.
How to cut graphite shafts?
Once you have marked the spot where you want to cut the shaft, reposition the shaft in the vice so that you can cut it comfortably and safely. Be sure to set the club in the vice in a way that will protect it from getting bent under the pressure you apply during cutting if you are using a hack saw. For steel shafts, a hack saw is the best option for a clean cut. For graphite clubs, you will need to use a rotary tool with a cutting wheel to get the best cut possible.
How long does it take for a golf club to cure?
Once you have the new grip in place, you will need to let the adhesive dry and cure. It will take approximately 6-8 hours for a full cure. It’s probably best to let the club dry overnight before you take it out for practice swings.
How to shorten a golf club shaft?
To do that, the DIY golfer will have to: 1 Remove the existing grip. 2 With steel shafts, use a tubing cutter to trim the shaft; with graphite shafts, shorten using a hacksaw. 3 Re-install a grip on the newly shortened shaft. 4 And, most importantly, Wishon says, add weight to the clubhead in some manner to restore the swingweight feel of the club. "If clubs are shortened and no weight is added back to the clubhead, the chances of the length reduction having the desired effect are somewhere between slim and none."
What is the difference between a golf shaft and a tip?
All golf shafts taper; that is, their circumference is greater at the grip end than at the tip end. That means that the grip end is the strongest part of the shaft and the tip end the weakest, which, Wishon says, leads trimming to have different effects: "Cutting more of the tip will have the effect of getting rid of some of the weaker end ...
Why add weight to a clubhead?
And, most importantly, Wishon says, add weight to the clubhead in some manner to restore the swingweight feel of the club. "If clubs are shortened and no weight is added back to the clubhead, the chances of the length reduction having the desired effect are somewhere between slim and none."
Do all golf shafts have to be cut down?
Did you know that almost all golf shafts are cut down to size before being installed in golf clubs? It's part of the manufacturing and club-building process for new clubs.
Should the reduction in length be made from the grip end only?
"If the goal in making the clubs shorter in length is a desire to gain an improvement in accuracy, the reduction in length should be made from the grip end only ," Wishon said.
