Slide the caliper over the rotor and line up the bolt holes. Bolt the piston part of the caliper to the caliper bracket. Note:sometimes the rubber boot will extend the bolt and cause interference during installation. Just push the rubber boot back to allow the caliper to slide over the rotor.
Full Answer
How do you replace the rubber boot on a caliper?
0:424:22Front brake caliper rubber boot replacement quick tip - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then you got to pull this end through here. And you can push on it and help it away. So you canMoreAnd then you got to pull this end through here. And you can push on it and help it away. So you can see how that rust is in there and this thing is hardening.
How do you put a caliper pin on boots?
2:2010:17How to Replace Brake Caliper Pins and Boots - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo now these boots here this one here actually come off there's a little metal part of it. That weMoreSo now these boots here this one here actually come off there's a little metal part of it. That we need to we're going to tap right here on the caliper bracket. And we should be able to just tap.
How do you install front brake clips?
1:102:21How to Install Brake Pad Retainer Clips - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you get the one end started make sure this is pushed in now this one here I actually install itMoreOnce you get the one end started make sure this is pushed in now this one here I actually install it in the hole there. And then use you just use my finger pressure here to push it down.
How do you put a spring back on a brake pad?
1:495:33Parking Brake Shoe Spring Installation Tip - YouTubeYouTubeStart of suggested clipEnd of suggested clipGet on this side. Same thing right through there twist it real tight. As tight as you can get it.MoreGet on this side. Same thing right through there twist it real tight. As tight as you can get it. All right and then release your pliers.
Where does caliper pin with rubber go?
0:532:35What is that piece of rubber "tube" on the lower brake caliper pin? | HondaYouTubeStart of suggested clipEnd of suggested clipAnd what I've seen happen over time over the years this rubber actually will swell up and it stopsMoreAnd what I've seen happen over time over the years this rubber actually will swell up and it stops the pin from moving freely inside here.
How do caliper slide pins work?
0:362:52Disk brake / Floating caliper brake - How it works! (Animation) - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhen pressure is applied to the caliper piston the caliper piston is actually displaced when theMoreWhen pressure is applied to the caliper piston the caliper piston is actually displaced when the pressure decreases the caliper piston returns to its initial. Position.
Does the brake pad with the clip go on the inside or outside?
0:031:02Brake pad clip orientation - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you can put the pad in on either side of the springy part for these clips. So that on this oneMoreAnd you can put the pad in on either side of the springy part for these clips. So that on this one on the right hand the inner side it basically is pushing up against the rotor.
How do you install anti-rattle clips?
0:121:57How to Install Anti-Rattle Spring | Clip Securing Brake Pad to CaliperYouTubeStart of suggested clipEnd of suggested clipNow you'll take your screwdriver. And put downward pressure prying. Against the caliper. So that itMoreNow you'll take your screwdriver. And put downward pressure prying. Against the caliper. So that it bends. To where it needs to be. And. Now we just slowly massage it into.
How do you install a retaining clip on a brake line?
0:093:02Reinstalling a Brake Hose, Retaining Clip & Anti-Lock Mounting BoltYouTubeStart of suggested clipEnd of suggested clipIn this step we're going to talk about the proper service procedure for reinstalling our brake hoseMoreIn this step we're going to talk about the proper service procedure for reinstalling our brake hose retaining clip. And anti-lock wheel speed sensor cable mounting bolt.
Replacing your brake pads is a very easy job to perform on your Volkswagen GTI MkIV and a great way to get started on "Doing it yourself"
In general, you should inspect your brake pads and rotors about every 25,000 miles, and replace them if the material lining of the pad is worn down enough to trigger the pad replacement sensor or there is less than a quarter inch of material on the pad.
Project Photos
Figure 1 Before you begin working on the brakes, check your brake fluid reservoir. You will need to compress the caliper piston which will cause brake fluid to travel back up into the reservoir and you need to make sure there is room for it (red arrow).