How do you remove the rear end of a golf cart?
Remove the rear end from the golf cart. Remove the tires and wheels. Move the lug nuts on the studs of the passenger side of the cart backward by a few threads. Position the cart so that the rear end of the passenger side is upward. This will make the armature hang out.
How do you remove a stuck spline from a golf cart?
Stuck armature on spline: To solve this problem, apply a few coats of WD-40 or PB Blaster around the spline and spline coupler and let it stay overnight. Shake, pull and tap on the armature a few times the next day until it comes off. The other option is to remove the rear tires and axle from the cart.
How do you remove a stuck motor from a car?
The lug nuts must also be loosened to the extent that they just hold the brake drum on to the axle. Get help from someone to lift the rear end by a few feet and drop it over the drum on to a concrete surface. Depending on how tightly the motor is stuck, you might have to repeat this step.
How do you fix a stuck club car motor?
Your Club Car motor may be stuck due to a stuck armature on the spline. The motor may also be stuck on the input shaft. To solve this problem, apply a few coats of WD-40 or PB Blaster around the spline and spline coupler and let it stay overnight.
How do you remove a motor from a golf cart?
0:375:58EZGO RXV Golf Cart Motor Removal & Installation How-To - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo remove this motor with us the connectors here we get it disassemble this wire to the front hereMoreTo remove this motor with us the connectors here we get it disassemble this wire to the front here we got to take off and they will just unbolt it slide it off.
How do you remove a 48 volt golf cart motor?
0:1612:391996+ EZGO TXT 36v/48v Motor Swap / Install ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow we've got the seat off we're going to remove the motor cover which it has one two screws rightMoreNow we've got the seat off we're going to remove the motor cover which it has one two screws right there. And then three on the back. Side now that i've got all five screws.
How do you remove an electric motor from a EZ Go golf cart?
3:169:45EZGO High Torque Electric Motor Swap | How To Install Golf Cart MotorYouTubeStart of suggested clipEnd of suggested clipOff while it's up in the air let's go ahead and we want to loosen and remove the rear shock thatMoreOff while it's up in the air let's go ahead and we want to loosen and remove the rear shock that gives you direct access. So you can unbolt it loosen everything and put it right out the side.
How do you remove a electric motor from a club car?
1:0213:29Replacing The Motor On a Club Car Precedent - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's the speed sensor that plugs into the end of it and there is three seven sixteenths longMoreThere's the speed sensor that plugs into the end of it and there is three seven sixteenths long bolts here. And then underneath the bottom there's one half inch bolt that has to be removed.
What size electric motor is in a golf cart?
If you have an Electric Golf Car: Change the field coil in a 2-hp motor (a standard in golf cars) and it can become a 3.5 hp motor.
Are golf cart motors interchangeable?
The motors and controllers are in no way interchangeable between a series and separately excited system, so be sure to educate yourself prior to ordering.
What are the 4 terminals on a golf cart motor?
If you're unsure if it is working, it is simple to test. There are four terminals on a solenoid: usually two large and two small. The small terminals are connected to the battery, and the large terminals are connected to the motor. Disconnect all wires from the two large terminals.
Where is the reset button on a ezgo golf cart motor?
Locate the motor Remove the panel so the electric motor is visible. Electric motors usually include reset buttons that can perform similar to circuit breakers. Look in the area where several electrical wires enter the motor and locate a small red button. This is the reset button.
How can I make my 36 volt golf cart faster?
6 Ways You Can Make a Golf Cart FasterAdd More Torque to Your Golf Cart.Upgrade Your Golf Cart's Motor.Improve the High-Speed Controller of the Cart.Add Better Golf Cart Tires.Use a Higher Powered Golf Cart Battery.Watch the Weight in Your Golf Cart.
How do you make a Club Car golf cart go faster?
0:131:31Club Car Precedent Speed Increase SUPER EASY!!! - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you turn it that way to the right or what appears to be counterclockwise. It slows it down. AndMoreIf you turn it that way to the right or what appears to be counterclockwise. It slows it down. And if you turn it that way or clockwise it speeds things up. Very.
How can I make my Gas Club Car golf cart go faster?
Increase the RPM An increase in the input shaft rpm for all differential ratios will produce a higher speed. For a gas golf cart, other than adjusting the governor, the speed may be enhanced by replacing the engine with a higher rpm output model.
How to get the motor off a golf cart?
Use a jack and lift the golf cart on the right axle side. Slide the motor off and catch it as it reaches the end of the shaft. Remember to set the motor down lightly on the surface. Use a small standard screwdriver and pull out the middle pin of the fastener by about one-quarter of an inch.
How to remove club car armature?
You can try the steps given here to remove an armature that is stuck on to the spline. Spray some WD-40 over the spline coupler and spline a few times. Allow it to rest overnight. Shake, pull and tap the armature.
How to remove lug studs from a cart?
Also, remember to lay your hands on an old brake drum and turn it backward or remove the lug studs so that the studs remain free of damage. Remove the rear tires and axle from the cart. Flip the brake drum and put it on backward. Raise the rear of the cart and drop it on to a hard surface.
How to release a club car motor?
You can follow the steps given below to release a Club Car motor that is stuck on the input shaft. Remove the rear end from the golf cart. Remove the tires and wheels. Move the lug nuts on the studs of the passenger side of the cart backward by a few threads. Position the cart so that the rear end of the passenger side is upward.
How to fix a drum on a car?
Remove the tires and wheels. Remove the brake drum and turn it backward. Adjust the lug nuts so that they are just tight enough to keep the drum on to the axle. Get someone to help you with raising the rear end by about three to four feet and drop it on to a hard surface over the inverted brake drum.
How to pawl a motor off?
Method 2. Keep a ratchet strap surrounding the motor but avoid tightening it. Loop a second ratchet strap below the first one under both the sides of the motor. Tighten the first strap around the motor as much as you can. Connect a third ratchet strap to the strap below the motor and pawl the motor off.
How to make armature hang out?
This will make the armature hang out. Apply a lot of PB Blaster, heat or both at the point where the shaft makes contact with the armature. When applying heat, try to keep it away from the armature shaft as much as you can. Raise the armature by about a foot length and slam it downwards.
