Why does my golf cart idle rather than shut off?
The golf cart will idle rather than shut off. Make sure you tell people before they drive the golf cart that you removed the safety feature. The relay on the throttle valve is a safety feature in place to prevent accidents. Use care and be aware of your surroundings.
Why won't my motor hold the speed at idle?
The carburetor is usually the culprit when a motor will not hold the speed or idle to which it is set. Check the carburetor to make sure it is clean and free of impurities.
Should the idle be set while the motor is in neutral?
In some models, setting the idle while the motor is in neutral will allow it to idle in neutral, but not hold an idle while engaged. In those models, you must set the idle while the motor is engaged. The carburetor is usually the culprit when a motor will not hold the speed or idle to which it is set.
Do you have to turn off the engine on a golf cart?
Security guards at airports who shuttle passengers back and forth, for example, have no need to have the engine shut off. Having the golf cart idle makes their job faster and easier. Remove the speed governor to shut this safety feature off on a golf cart.
What causes a gas golf cart to stop running?
Your golf cart may stop frequently while running in case of a faulty spark plug, defective TCI/carburetor, or improperly seated internal baffles and airbox lid. Sometimes, an empty or close-to-empty fuel filler, low battery charge, a binding linkage, or a bad fuel pump can cause a golf cart to stop running.
How do you adjust the carburetor on a Yamaha golf cart?
How to Adjust Yamaha Golf Cart CarburetorPull out the pilot adjustment screw. ... Rethread the screw back until it's slightly seated.Turn the screw outwards by 1-1/2 turns.Push the throttle stop screw backward until the throttle shaft is closed completely.Turn the screw in by a 1/4 turn.
How do you adjust the carburetor on a gas golf cart?
Find the pilot adjustment screw on the edge of your carburetor. Pay attention to this screw – it should be a sharp point and not flat. Carefully remove this screw and then carefully screw it back. Turn this screw out one and one-half turns to adjust it properly.
Why does my 2 stroke golf cart backfire?
Engine backfiring occurs when there is an air leak within your golf cart or sometimes when there is too much fuel inside. This can cause the piston to slam against the cylinder head and cause a tapping sound. An essential component of any golf cart is the drive belt.
How do you clean the carburetor on a Yamaha golf cart?
2:1217:47How to Take Apart and Clean a Carburetor - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf there's some little crevices with gunk in it and so what I do after I take time to clean it is IMoreIf there's some little crevices with gunk in it and so what I do after I take time to clean it is I use some brake cleaner.
How do you adjust the throttle cable on a Yamaha golf cart?
0:005:15Yamaha G29 Drive Golf Cart Governor Adjustment - MORE SPEED!!YouTubeStart of suggested clipEnd of suggested clipItself by tightening this nut down you're putting more pressure on the spring. So that the governorMoreItself by tightening this nut down you're putting more pressure on the spring. So that the governor has to work harder to pull back on the throttle. Cable.
How do you adjust a 2 stroke carburetor?
0:5014:002 Stroke Carburetor | How to Tune | How it Works | Basic PrinciplesYouTubeStart of suggested clipEnd of suggested clipAnd screw these right in until they can't go in anymore. So that will set them at ground zero if youMoreAnd screw these right in until they can't go in anymore. So that will set them at ground zero if you like and then we turn them out. One. Full turn each. And we can go from there.
How do you take the governor off a Yamaha golf cart?
General InstructionsDetach the cable from the carburetor. The cable is about the width of a straw. ... Follow the disconnected cable up to the governor. ... Disconnect the gas pedal cable from the governor and reroute it to the carburetor. ... Using your wrench, remove the bolt on the gas pedal shaft.
How do you take the governor off a gas golf cart?
0:000:46How to remove governor on a Club Car golf cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou open up this box lap. Here. It looks up look inside. There's 12 cable down right here this leverMoreYou open up this box lap. Here. It looks up look inside. There's 12 cable down right here this lever you want to lift up and Bend and that pulls on the cable a little more.
How do you stop a Yamaha golf cart from backfiring?
One simple way to stop the golf cart from backfiring is to use good quality fuel. Once this is done, ensure that the throttle plate is closed by adjusting the accelerator cable at the plate.
How do I stop my golf cart from backfiring?
Start by carefully removing the drive belt with the engine off and then tweaking the adjustment screw as the engine is running. Adjust the screw until the engine is running as smoothly as possible. Now, you can fully tighten the screw, turn off the engine, and replace the drive belt to start your cart up again.
Why does my Yamaha golf cart backfire?
In almost all cases, whether it is a 2 cycle or 4 cycle engine, golf cart backfiring is caused by the accelerator cable being out of adjustment at the throttle plate of the carburetor. This problem has a relatively simple cure.
How to fix a carburetor so idle speed will reduce?
The first step in correcting a carburetor so the idle speed will reduce is to properly start the engine. Move the throttle to the "Start" position, and then press the primer bulb three times to introduce fuel mixture into the carburetor for starting.
What is a 2 cycle engine?
Two-cycle engines are common features on mowers and trimmers, such as the Lawn-Boy model 10201 walk-behind mower. Two-cycle engines require that 2-cycle engine oil be mixed with gasoline instead of adding gas and oil separately. The carburetor on 2-cycle engines comes pre-set from the factory for optimal performance.
Why does my lawn mower lurch forward?
On self-propelled models, such as the 10201, a rear bar mounted on the handlebar is pressed to engage the self-propelled drive system. A high idle speed can cause the mower to lurch forward when the drive wheels are engaged , resulting in the operator potentially losing control.
How to fix a carburetor?
The first step in correcting a carburetor so the idle speed will reduce is to properly start the engine. Move the throttle to the "Start" position, and then press the primer bulb three times to introduce fuel mixture into the carburetor for starting. The blade control bale, or lever, should be pulled up against the handle bar at which point the starter rope can be pulled. When the engine starts, move the throttle lever to the "Run" position and let the engine warm up for three minutes or so.
What does opening the throttle plate do?
Opening the throttle plate increases the idle speed, and closing the throttle plate reduces the idle speed. Excessive idle is typically noticed when the throttle trigger is released and the engine does not idle down but instead remains at a higher speed.
Can carburetor settings change over time?
The carburetor on 2-cycle engines comes pre-set from the factory for optimal performance. However, as the result of normal use, the idle settings can change over time, resulting in issues like excessive idle speed.
What to do when gasoline sits idle?
When a gasoline engine of any kind will sit unused for any length of time, drain the fuel from the tank and run the engine until all remaining fuel in the system has been burned through the engine. This prevents gums and varnishes from closing off small openings. Ask Question.
How to tighten carburetor?
First check the mounting screws for the carburetor and tighten them. Then go to the screws that hold the cylinder head to the crankcase body and those that cover the end where the crankshaft comes out of the engine . See the yellow circles on this photo of a weed whacker engine.
How to clean exhaust ports?
Step 1: Clean the Exhaust Ports, Too. Remove the muffler. The exhaust ports are under it. In time carbon residue from the burned oil in the fuel mixture begins to close off the exhaust ports. An engine is an air pump.
How to troubleshoot a 2 stroke engine?
Basic 2 Stroke Engine Troubleshooting And Tips 1 You have fuel in your fuel tank. 2 You remembered to "turn on the gas" (your fuel shutoff valve is "on"). 3 Your engine kill switch is in the "run" position.
What do 2 stroke engines need to run?
There are really only 3 things your 2 stroke engine needs to run: Air. Spark. Fuel. Yep, it's that simple. Now this is of course providing your engine isn't blown up with a hole in the piston or something. Typically if you can "feel" resistance in the form of compression as you kick or pull your engine over, and it's not making any horrible banging ...
Why do we check spark plugs?
There are 2 reasons that we are going to check spark before we see if your engine is getting fuel: To check spark, we are going to pull the spark plug, if the spark plug is wet, there is a good indication we ARE getting fuel. If the plug is dry and we have spark, we are not getting fuel.
How to check if gas is flowing out of carburetor?
One quick check you can do is to pull the fuel line off your carburetor , turn the gas on for a second and see if fuel is flowing out the fuel line.
Where is the drain plug on a 2 stroke carburetor?
Most 2 stroke engine carburetors have an access plug or drain plug in the bowl on the bottom of them. Remove this plug (you may have to loosen the carb and tilt it to access this, or even remove the carb from the machine in some cases).
Can you put water in your car's fuel tank?
Go to your nearest gas station and grab a bottle of isopropal heet, yes the stuff you put in your car gas tank in the winter. Add a bit of this to your new fuel to wick the remaining moisture out of your fuel system.
What was the first Yamaha cart?
Yamaha’s premiere cart in 1979 was the G1A Model J10 Gas-powered vehicle that featured an Autolube Oil Injection System to supply oil to the engine in precise oil-to-gas ratios. This eliminated the premixing of the oil and gas and improved combustion, oil consumption, and carbon buildup. In 1980, Yamaha introduced the G1E 36 volt Electric J14 series.
What is a golf cart?
Golf carts are also known as golf cars. The term "cart", in its purest sense, refers to a vehicle that does not travel under its own power. Golf cars, however, are most commonly referred to as golf... link to Club Car DS Wiring Diagrams 1981 To 2002.
What is an electric cart solenoid?
The first generation electric cart had solenoids (or relays) that had all terminals on one end of the unit. These solenoids are no longer available and are replaced with a model with terminals on both ends. Below is the retrofit for replacing these with a contemporary solenoid.