
Apply epoxy all around the inside of the hosel. Then, apply epoxy all around the bottom of the shaft, as well. Gently, push the shaft into the hosel and twist it a bit to make sure the shaft is all the way down in the hosel. Use acetone
Acetone
Acetone, or propanone, is the organic compound with the formula₂CO. It is a colorless, volatile, flammable liquid and is the simplest and smallest ketone. Acetone is miscible with water and serves as an important solvent in its own right, typically for cleaning purposes in laboratories. About 6.7 …
How do you replace a golf club shaft?
How To Re-Shaft Your Steel Golf Clubs
- Carefully clamp the shaft into a vise using a Shaft Vise Clamp. ...
- When removing steel shafts from clubheads, use a torch to heat the hosel. ...
- After 30 seconds of heating, with your gloved hands grasp the head and twist/pull the head. ...
- Using a wire brush remove excess epoxy from the inside of the hosel.
How do you shorten a golf club shaft?
To do that, the DIY golfer will have to:
- Remove the existing grip.
- With steel shafts, use a tubing cutter to trim the shaft; with graphite shafts, shorten using a hacksaw.
- Re-install a grip on the newly shortened shaft.
- And, most importantly, Wishon says, add weight to the clubhead in some manner to restore the swingweight feel of the club. ...
How to install a new Golf Club shaft by yourself?
putters)
- Pro-Fix 20/20 Long Cure Epoxy
- Ferrule Make sure you purchase the correct size! ...
- Drill Driver and Small Drill Bit (for removing old epoxy inside the shaft)
- Epoxy Board (or some smooth surface to mix the epoxy on)
- Something to mix the epoxy with (end of a paintbrush, nail, screwdriver)
- Coarse Sand Paper (80 Grit works fine)
How to replace a golf club shaft?
Steps to Replace a Golf Club Shaft at Home
- Choosing the Right Golf Club Shaft. To begin with, you will need to get your hands on a golf club shaft. ...
- Cleaning the Club. Now, take out your utility knife. ...
- Taking the Shaft Out. It is now time to release the head from the shaft. ...
- Scrapping off Any Residuals. ...
- Installing a New Shaft. ...
- Finishing Touches. ...

Can you change golf shafts yourself?
Shafts can be replaced at golf pro shops and most golf stores, but it is also a fairly easy project to do yourself. Replacing your own shaft can save time and money, and allow you to try a new shaft without purchasing new clubs.
How do you Reshaft a golf club at home?
2:2522:36GOLF CLUB BUILD - How to reshaft your irons Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipUp the house'll. Pull the shafts you don't need a shaft puller. Anything like that you can just heatMoreUp the house'll. Pull the shafts you don't need a shaft puller. Anything like that you can just heat them up and twist them off because it's a steel shaft.
Can you Reshaft a driver yourself?
Replacing your old shaft can be a relatively painless process for you or your local repair shop. If your favorite old driver seems to have run out of quality hits, you might want to refresh it by adding a new shaft to the club.
How do I change a golf club shaft?
1:465:54Golf Equipment : How to Change a Golf Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipUp as that shaft heats the epoxy starts to break down. And then the shaft the head of the club willMoreUp as that shaft heats the epoxy starts to break down. And then the shaft the head of the club will come will pull off of that shaft. Once that epoxy gives way then you can turn your heat gun.
How much does it cost to get clubs Reshafted?
The average cost to reshaft your golf clubs is $24 per club plus the cost of the shaft and grip. A new iron shaft and grip can range between $10 and $95 while a new driver shaft and grip can range between $18 and $440. The majority of the cost comes down to what type of shaft you want and what grips you like.
Is it easy to Reshaft irons?
Golf irons can be a bit easier to reshaft than a driver. If you are reshafting with steel irons, it is usually pretty straightforward. However, you will need the proper tools and space to complete this project.
Do all shafts fit all heads?
Yes, most golf Driver shafts are interchangeable. Golf driver shafts can be replaced as long as the new shaft is the same length and made by the same brand of golf club.
How long does it take to Reshaft a golf club?
If in stock, our Certified club repair technicians can have your new shaft installed and ready for play within 48 hours.
What flex should I use golf?
– Golf Shaft Flex ChartCarry DistanceSwing SpeedFlexUnder 200 yardsUnder 75 mphLadies or Senior200 to 240 yards75 to 95 mphRegular240 to 275 yards95 to 110 mphStiffOver 275 yardsOver 110 mphStiff or Extra StiffOct 15, 2019
How much does it cost to Reshaft a driver?
The cost of reshafting a golf driver is between $15 and $45 USD. The labor cost of reshafting is usually around $20 USD. However, the actual overall cost can also depend on the materials used as well as the type of grip and shaft you are looking at.
How do you cut a graphite golf shaft at home?
1:2914:05Golf Club Repair - How To cut a Golf Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you're gonna if this is going to be your primary cutting tool don't skimp alright I'm a big toolMoreIf you're gonna if this is going to be your primary cutting tool don't skimp alright I'm a big tool nut don't skimp even if it's a hand tool.
How do you pull a golf shaft?
6:2514:27pulling a golf shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd I like to do is I like to pinch. Down. And then pull back pinch down and then pull back. AndMoreAnd I like to do is I like to pinch. Down. And then pull back pinch down and then pull back. And this way you don't scrape a shaft.
How to remove a broken shaft from a vise?
Step 1. Insert the broken shaft into the vise and remove the shaft by using the heat gun to warm up the hosel and loosen the adhesive that holds the shaft in place. Use medium heat for graphite shafts and higher heat for steel shafts. Once the adhesive has started to melt, pull the broken shaft from the hosel, which is where the shaft meets ...
Can you replace a golf club shaft?
Once a golf club shaft has been broken, it cannot be repaired, but it can easily be replaced. Shafts can be replaced at golf pro shops and most golf stores, but it is also a fairly easy project to do yourself. Replacing your own shaft can save time and money, and allow you to try a new shaft without purchasing new clubs.
How to remove ferrules from hosel?
Use the utility knife to cut off the ferrule, which is the small plastic piece by the hosel. A little heat may be necessary if the ferrule is difficult to take off. If so, put the butane torch near it.
How to clean a hosel?
If so, follow the instructions for this. Apply epoxy all around the inside of the hosel. Then, apply epoxy all around the bottom of the shaft, as well. Gently, push the shaft into the hosel and twist it a bit to make sure the shaft is all the way down in the hosel. Use acetone to clean off any excess epoxy on the shaft or hosel.
Do putter shafts wear down?
By Tami Fisher. Even putter shafts can wear down over time. People often like to change the shaft in their golf club, whether it's because the current one broke or because they want to try out the newest one on the market without purchasing a new club.
How to remove a broken shaft from a golf club?
If there is an existing or broken shaft on the club, the first step is to remove it. You need to break down the epoxy bond between the shaft and the head. To do this, you need to provide even heat to the hosel (where the club head attaches to the shaft). This can be achieved by using either a torch or a heat gun.
How to remove old epoxy from hosel?
There are two ways to remove the old epoxy: hosel cleaner or a round file (hosel cleaner is less time consuming). Once you've cleaned the hosel, apply some acetone to the inside of the hosel to remove grease and debris.
How often should I replace my golf grips?
Typically the rule of thumb is that you can replace your grips about every 18 months if you play 1-2 times a week, and live in a cold-weather climate.
How long does it take to regrip golf clubs?
The whole process of regripping golf clubs is probably going to take you somewhere between 1 to 2 hours. I wouldn’t call it an easy project, but once you do it once you’ll probably be comfortable doing it forever.
What happens if you don't get the grip on your grip?
You absolutely want to get that grip on quickly and aggressively. If you don’t get the grip all the way down and it gets stuck, then you will likely be throwing that grip away. For you beginners out there, I would expect to possibly botch one or two attempts, which is why I recommend buying a couple of extra ones.
Can you regrip golf clubs at home?
Since I am not the most “handy” person in the world, and don’t have much experience regripping golf clubs , I decided to enlist the help of my friend Nick Banks who actually knows what he is doing since he is a PGA professional.
Can you spray a grip with solvent?
You almost can never have enough grip solvent! If you have a spray bottle or a tube, the first step is to place your finger over the small hole at the butt of the grip (this will prevent it from leaking out). Then you apply a generous amount of solvent to the inside of the grip.
Can you spray paint on a grip?
This is another step where you want to be generous with the solvent. You can even spray some extra solvent on the tape afterwards, it’s only going to make it easier to apply the grip.
Step 1: Remove the old grips
First, cut or peel off the old grips, which may or may not be straightforward depending on how long they’ve been on.
Step 2: Preparation
Next, starting at the butt end, wrap the double-sided tape round the grip working downwards and allowing sufficient space so that it doesn't start overlapping lower down as the grip gets narrower.
Step 3: Fitting the new grips
Place the club in the vice with the head pointing up, taking care to use a shaft protector (or similar) to avoid damage as you tighten.
