What does a speed sensor magnet do on a golf cart?
A golf cart speed sensor magnet increases the speed by up to 21mph on a 48V Precedent IQ and Club Car DS golf carts that use ADC motors without any loss of torque. With a slight reduction in torque, the speed can be increased further up to 28mph. The speed sensor magnet can be replaced easily in the speed sensor.
What happens if the magnet on a golf cart goes bad?
Also, if the magnet is broke and/or the speed sensor is bad the cart will go into “limp-mode”. Make sure the car isn’t in sleep mode. This can be accomplished by driving the cart a few feet. Just make sure the cart is running.
What size magnet do I need for my club car?
Stock magnets for Club Car IQ, Excel carts, EZ-GO 36/48 volt PDS carts and Yamaha G19, G22 and G29 carts are 8 pole. A proper speed magnet should be half count or less. To get the same result as a high speed magnet for Club Car Regen 1 and Regen 2 carts, simply unplug the speed sensor. Note: You can’t do this on the IQ and Excel controller carts.
How do you install a magnet on a golf cart?
While the instructions might be lacking a tad, it is really easy to install. Simply jack up the back of the cart, remove the rear passenger wheel, take off the two bolts that hold the existing magnet bracket on the shaft, and then swap this unit in for the old one. The old magnet will slide right off and this will slide back on on in it's place.
What does a speed sensor do on a Club Car golf cart?
A golf cart speed sensor interprets the rpm of the motor and passes on this detail to a speed controller present in the golf cart. This helps to keep control over several motor functions including roll-away protection and regenerative braking.
How do you make a Club Car golf cart go faster?
6 Ways You Can Make a Golf Cart FasterAdd More Torque to Your Golf Cart.Upgrade Your Golf Cart's Motor.Improve the High-Speed Controller of the Cart.Add Better Golf Cart Tires.Use a Higher Powered Golf Cart Battery.Watch the Weight in Your Golf Cart.
Can you adjust the speed on a Club Car golf cart?
0:131:31Club Car Precedent Speed Increase SUPER EASY!!! - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you turn it that way to the right or what appears to be counterclockwise. It slows it down. AndMoreIf you turn it that way to the right or what appears to be counterclockwise. It slows it down. And if you turn it that way or clockwise it speeds things up. Very.
How do you remove the speed limiter on an electric Club Car?
0:040:46How to remove governor on a Club Car golf cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou open up this box lap. Here. It looks up look inside. There's 12 cable down right here this leverMoreYou open up this box lap. Here. It looks up look inside. There's 12 cable down right here this lever you want to lift up and Bend and that pulls on the cable a little more.
How can I make my electric golf cart go faster without upgrading?
How to Make an Electric Golf Cart Faster Without UpgradesWash Your Cart Properly. ... Inspect the Batteries. ... Refill the Battery Water. ... Check the Gas Pedal and Linkage. ... Measure the Tire Pressure. ... Charge Up Your Battery Unit. ... Lighten Up Your Cart's Weight.
Why is my Club Car so slow?
The main reasons for a Club Car Precedent running slow is because of a weak battery, or faults with the MCOR, solenoid and throttle cable. Some of the other reasons the cart may slow down are: Solenoid contacts can get jammed as they wear out; experts call this 'welded solenoid'. The MCOR could be an issue.
What does a high speed magnet do?
This high speed motor magnet will increase the speed of your cart from 3-6 MPH based on your carts condition (This is not a guarantee). Does not matter if your Precedent speed setting is 3 or 4 you will still get results without any loss of torque.
How do I change the speed on my Club Car?
If you want to change your speed code, you will need to find a local golf cart dealer to change this speed setting for you. You could try to do this yourself, but would need an expensive Curtis handheld programmer. They usually charge a fee that can range from $75-$100.
How does an electric golf cart speed controller work?
The golf cart's speed controller sends its current and battery voltage to its motor. This entire process depends on your golf cart's input device, which includes its throttle. That's how the golf cart's speed controller allows you to operate its acceleration rate, as well as its deceleration rate.
Why is my electric golf cart so slow?
Low Battery Usually, the most common reason golf carts slow down is when they don't get enough power output from the battery. If the battery pack charge is very low and your cart is out of power, your cart will run slow.
Why does my electric golf cart go slow uphill?
The Reason Your Electric Golf Cart Goes Slow Uphill? Your electric golf cart can struggle on inclines for a variety of reasons. Weak batteries, incorrect tires, and wear and tear to the motor and wiring are all potential causes of your cart's slow speed.
How can I make my golf cart gas faster?
Get Bigger Golf Cart Tires If you don't want to touch your golf cart motor, but want to increase the speed of your gas cart, one easy method you can try is installing larger tires on your cart. Standard golf cart tires are approximately 8 inches in diameter. However, the larger the diameter, the faster your golf cart.
Videos
I have a 2006 club car 48VDC, motor is shown in pic. Remove the passenger side rear tire then access to back of drive motor is very easy. Remove two screws then you will see original magnet, replaced with this one and done.
Top reviews from the United States
There was a problem filtering reviews right now. Please try again later.
Product Description
Installation Instructions: 1: Flip the Tow/Run Switch to the TOW position (this should be done whenever you are servicing the cart) 2: Disconnect main positive and negative battery cables to your cart 3: Remove the ADC speed sensor from the end of your cart motor 4: Now you can gain access to the magnet.
Top reviews from the United States
There was a problem filtering reviews right now. Please try again later.
How does a golf cart speed controller work?
The golf cart's speed controller sends its current and battery voltage to its motor. This entire process depends on your golf cart's input device, which includes its throttle. That's how the golf cart's speed controller allows you to operate its acceleration rate, as well as its deceleration rate.
Why is a speed controller important?
Why Club Car Speed Controllers are Important. The basic function of a speed controller is, as the name implies, to control and manage the cart's speed. If your golf cart is working on a Brushless DC or AC motor, you will not be going anywhere without a speed controller.
How many amps does a club car need?
If the cart is mainly used to transport 1 to 2 people or light loads on smooth roads, a small 2-5 horsepower and lower controller around 200-300 Amps will work best.
How to control a cart's speed?
In addition to controlling the cart’s speed, there are a few other functions that speed controllers can offer. Limit the current to the motor to protect both engine and controller in case of overloading. Determine the battery current so that battery is protected from excessive discharging. Monitor battery health and charge.
What does it mean when there is no controller?
When there is no controller, it means battery drainage is at its peak, as motors can operate independently at their high speed, which increases stress on the mechanical and electrical components. A speed controller notes the battery voltage and current to the motor based on operator input types like the throttle, twist grip, or pedal force.
Why replace club car speed controller?
There are several reasons why you might want to replace or repair your Club Car speed controller, including customization of Club Car, adjustment or upgrade of the motor, or upgrading Club Car controller to better fit your needs.
Why limit current to motor?
Limit the current to the motor to protect both engine and controller in case of overloading.
Regenerative Braking
Regenerative braking is a method used to make the motor act as a generator to governor the golf cart’s speed to a preset rpm, as well use the power generated to slightly recharge the batteries. Thus the need to know the motor rpm is evident so the controller can control such features.
Magnetic Style
Many golf cart motor speed sensors employ an electromagnetic power to “read” the motor rpm. Generally, there is a magnet present in the closed end of the motor as well as the sensor itself which reads how the magnet is reacting with the magnetic field inside the motor.
Mechanical Style
Another motor speed sensor type is mechanical based. This type of sensor uses a disk with slots in it, which passes by an eye or reader head. Depending on how many slots are read per minute translate into a calculation within the speed controller to determine motor rpm.
Bearing Style
The last golf cart motor speed sensor type we’ll mention is both mechanical and electrical. The EZGO RXV 48V golf cart uses a 3-phase AC induction motor made by Iskra in Slovenia. In the earlier models, from 2008-2010, the motor used a bearing type sensor on the outside end plate of the motor before the motor brake disk.
What is a Golf Cart Speed Sensor?
A golf cart speed sensor interprets the rpm of the motor and passes on this detail to a speed controller present in the golf cart. This helps to keep control over several motor functions including roll-away protection and regenerative braking.
How to test a speed sensor on a golf cart?
Two methods of testing your speed sensor are the following: Activate the Run/Tow switch of the golf cart by keeping it in Run position and try to push the cart.
How to check voltage on golf cart?
Ensure that the 3-pin plug from the sensor is connected and place a wire-piercing probe on the output green wire. Lift one wheel of the golf cart and turn it one full rotation with your hand. The voltage reading should change from 0V to 5V 24 times for one full revolution.
Why does my golf cart stutter?
Your golf cart may move very slowly as if it’s creeping along or it may move at an erratic speed. You may experience stuttering in your golf cart like when you have a bad battery or there is a low voltage problem. A broken or damaged magnet on the motor can result in a bad speed sensor.
What type of motor does a golf cart use?
A golf cart uses either an AC or a DC motor. DC wound motors don’t incorporate golf cart speed motors because they don’t have many features such as roll-away protection and regenerative braking.
What happens if a motor magnet is broken?
A broken or damaged magnet on the motor can result in a bad speed sensor. If this is replaced with a new magnet, the speed sensor will begin to function properly. Alternatively, the magnet could have just come loose. If so, all that you have to do is to tighten the magnet.
Why do golf carts roll off?
Roll-away protection is essential for the safety of the golf cart. If the parking brake is not activated, the golf cart tends to roll off when it is in a neutral position and stopped in an incline.
What happens if you unplug the speed sensor on an Excel cart?
However, with IQ or Excel systems if you unplug the speed sensor this puts the cart into “ limp-mode” and will not allow the cart to run full speed. Also, if the magnet is broke and/or the speed sensor is bad the cart will go into “limp-mode”.
What is IQ on a Club Car?
It consists of a shunt wound motor/controller combination much like the older Regen 1 and Regen 2 (PowerDrive Plus) carts. All DS IQ cars have a serial number prefix of “AQ” All Precedents are equipped with either the IQ or Excel system. The Excel system functions very similar to the way the IQ system does so this information applies to them as well. If you have a Regen 1 or Regen 2 cart you can simply unplug the speed sensor and eliminate regenerative motor braking. However, with IQ or Excel systems if you unplug the speed sensor this puts the cart into “limp-mode” and will not allow the cart to run full speed. Also, if the magnet is broke and/or the speed sensor is bad the cart will go into “limp-mode”.
What does it mean when a cart pushes freely?
If the cart pushes freely with no resistance this will let you know that there is no communication from the cart speed sensor to the controller. This means you have a speed sensor failure and it needs to be replaced. There are two different motors used on these carts and each have a different speed sensor.
How many poles are in a club car magnet?
Stock magnets for Club Car IQ, Excel carts, EZ-GO 36/48 volt PDS carts and Yamaha G19, G22 and G29 carts are 8 pole. A proper speed magnet should be half count or less.
How to take the rear end off a cart?
Take the rear end out of the cart. Take the tire off the rear end on the same side the motor slides off the rear end spline, take the brake drum off, flip the brake drum around backwards and tighten the lug nuts snug enough to hold the drum to the axle, this is to protect the wheel studs.
Can you unplug the speed sensor on a Regen 1 cart?
The Excel system functions very similar to the way the IQ system does so this information applies to them as well. If you have a Regen 1 or Regen 2 cart you can simply un plug the speed sensor and eliminate regenerative motor braking.
Can you run 6 ga wire through an OBC?
You can leave the stock 6 ga. wire running through the OBC and simply route a larger gauge wire around the OBC.