The absence of a spin in this test could mean your Yamaha golf cart’s battery pack is failing. The controller is one major component that may have to be replaced. A faulty controller can stall the cart and the click you hear must be from the solenoid.
Full Answer
Why does my Yamaha golf cart controller keep dying?
The controller on a Yamaha golf cart can die when the battery voltage is too high, or because of loose wiring in the charger. The batteries’ voltage: This is one of the primary reasons for your golf cart controller’s death. There are times when the battery voltage is too low or too high.
Why is my Yamaha golf cart clicking but not moving?
The main cause of a Yamaha golf cart clicking but not moving, is a faulty controller or solenoid. The battery has to be checked first to see if it’s delivering the right voltage while in the idle state as well as when the pedal is pressed. There can be other reasons for the Yamaha golf cart not moving though you hear the click.
What are some of the problems with the 1996 Yamaha Ydre?
Generally, defective batteries and the motor are major causes of all the problems of a speed controller on a Yamaha YDRE. The 1996 Yamaha golf cart can also encounters controller problems. Remove the controller and check for defects, as mentioned in the previous sections. If you find any defects, get a new controller.
How to troubleshoot the Yamaha G29 golf cart controller?
The troubleshooting process for the Yamaha G29 controller is almost the same, as discussed in the previous sections. Examine the voltage levels of the batteries to check if the controller receives enough voltage. Next, examine all the wired connections of the controller to detect the problem. Yamaha YDRE golf cart controller troubleshooting
How do I know if my golf cart controller is bad?
X Common Symptoms of Controller FailureTop Speeds Not Appropriate for Your Cart. Golf carts are designed to reach pretty specific speeds and to not go over them or beneath them. ... Sudden and Unexpected Slowing. ... Shuttering or Shaky Driving. ... Stalling Out and Refusing to Start. ... Surges in Speed When Driving.
How do I test my Yamaha golf cart speed controller?
How do I test my Yamaha g16 speed controller?Keep the key on.Press down the accelerator.If you hear a clicking noise, the solenoid is working. Otherwise, there is a problem.Next, examine the controller for defects. ... If the wires are damaged, replace them to get back the speed.
What does a golf cart controller do?
The controller meters out current and voltage on your battery based on user input, whether that be a gas pedal, a throttle, or even pedals on a bicycle. With the controller you are able to control your acceleration and deceleration, as well as the speed at which your vehicle moves.
How do you test a golf cart controller?
To test a club car precedent controller, connect a voltmeter between the negative terminal of your cart's battery and the M terminal on the controller. Then push the pedal down and look for a clicking noise from the solenoid. Your batteries should read as full.
How do I reset my Yamaha golf cart remote?
Identify your main battery supply (usually the largest battery) on your motor. Check around this supply for a small red button that may or may not be labeled “Reset”. Press and hold this button for a few moments and then release it to reset the motor.
Where is the reset button on a Yamaha golf cart motor?
Expose the motor (you'll probably need a screwdriver to remove the cover), and look for a red button. It is usually near the main power source, where most of the wires are connected. Once you've pressed the button to reset the motor, reassemble the cart, charge up the batteries, and give it a test run.
How do you bypass a golf cart controller?
1:594:09electric golf cart, simple Motor and controller bypass key hotwire direct ...YouTubeStart of suggested clipEnd of suggested clipSo let's just go ahead and bypass the solenoid by putting one alligator clip on that bolt.MoreSo let's just go ahead and bypass the solenoid by putting one alligator clip on that bolt.
How much is a golf cart speed controller?
Each Controller is completely epoxy potted, which eliminates all controller failures due to vibration and water corrosion. These controllers produce up to 60% less heat than many competing controllers....Part #Series ControllersAmpsPrice400$565500$649600$6802 more rows
How do I test my Club Car speed controller?
0:002:12How to bench check curtis controller and golf cart motor - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay guys i'm going to show you right quick how to easily bench check your club. Car actually anyMoreOkay guys i'm going to show you right quick how to easily bench check your club. Car actually any golf cart. That's got one of these curtis controllers in it you just simply want to take that
How do I fix my golf cart controller?
Here are 5 steps you should follow for a DIY fix to your golf cart's speed controller.Flip the maintenance switch. ... Reset the battery cable. ... Check your connections. ... Test the solenoid. ... Check your controller's power output.
How do you test a motor controller?
How to Test an Ebike Controller at HomeStep 1: Connect your controller to the battery.Step 2: Set the multimeter reading. ... Step 3: To test for continuity, set your multimeter to continuum. ... Step 4: Test every line that comes out of the controller. ... Step 5: Set your multimeter to resistance mode to test for resistance.More items...•
Where is the reset button on an electric golf cart motor?
First, you'll want to reset your motor. It should have a small reset button (Usually it will be red) located near the main battery supply. Hit the reset button and then put the cover back on the motor. The next step would be to recharge your cart and try turning it on again. If it starts up then you're in luck!
How can I test my speed controller?
0:395:30Testing controller for blown mosfetts - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe start by connecting one of the probe to the ground wire of the controller. And you take theMoreWe start by connecting one of the probe to the ground wire of the controller. And you take the positive probe.
How do you test a speed controller on a Club Car golf cart?
0:002:12How to bench check curtis controller and golf cart motor - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay guys i'm going to show you right quick how to easily bench check your club. Car actually anyMoreOkay guys i'm going to show you right quick how to easily bench check your club. Car actually any golf cart. That's got one of these curtis controllers in it you just simply want to take that
How do you test a speed sensor on a golf cart?
What is this? Activate the Run/Tow switch of the golf cart by keeping it in Run position and try to push the cart. If your speed sensor is good, you should hear a beep and experience resistance to the pushing action by slowing down. If the sensor is bad, your cart will start rolling.
Where is the reset button on an electric golf cart motor?
First, you'll want to reset your motor. It should have a small reset button (Usually it will be red) located near the main battery supply. Hit the reset button and then put the cover back on the motor. The next step would be to recharge your cart and try turning it on again. If it starts up then you're in luck!
Where is the controller on a golf cart?
This controller is typically located under the seat on your golf cart. Determining if the controller is bad is a relatively simple procedure. Lift the golf cart's bench seat to gain access to the engine. Locate the governor on the engine. This is the small “T”-shaped metallic rod around the top of the golf cart’s motor.
How fast does a golf cart go?
The speed controller, also known as the “governor,” generally keeps a golf cart from exceeding 10 miles per hour.
How to find the governor on a golf cart?
Locate the governor on the engine. This is the small “T”-shaped metallic rod around the top of the golf cart’s motor. Look for the carburetor in the engine. The carburetor is the cylindrical shaped object in the engine that has valves pointing up and out of the motor. Pull on the governor closer to the carburetor.
Why is my Yamaha golf cart not clicking?
Check the controller if you find that your Yamaha golf cart’s solenoid is not clicking after you have installed a new set of batteries. This can happen and you must first check the controller.
What does absence of spin mean on Yamaha golf cart?
The absence of a spin in this test could mean your Yamaha golf cart’s battery pack is failing.
Why My Yamaha Golf Cart Solenoid Clicks but Won’t Move?
The main cause of a Yamaha golf cart clicking but not moving, is a faulty controller or solenoid.
Why is my G29 not moving?
Some experts think that faulty batteries are the main reason for G29 Yamaha golf carts not moving when started. With the batteries, there can be multiple issues. Keeping them charged to the full is important.
Why is my solenoid not clicking?
The reason why the solenoid is not clicking could be that it is faulty or has no grounding. Experts recommend checking all wiring and cable connections to rule out this possibility. Batteries on your G16 Yamaha golf carts should raise sufficient power to reach the solenoid and the starter/generator.
How to check solenoid on a G9 golf cart?
The solenoid can be checked using an old screwdriver to jump the terminals. Your G9 Yamaha golf cart’s key must be in the start position. If the starter turns when you do this, your solenoid needs to be replaced. You must be careful while doing this crude test; there could be sparks when the two terminals touch.
How to connect a battery to a solenoid?
Take a jumper cable and connect them from the positive and negative posts of the battery pack to the two posts on the solenoid that you just disconnected.
What does it mean when a golf cart solenoid goes bad?
Technically, in fact, a solenoid is a shape – a shape in which the length of something coiled is longer than the diameter of the coils. In engine starters, this refers to the smaller motor ...
What are the symptoms of a bad solenoid on a golf cart?
In addition, the spring that pulls the pinion back to its resting position could wear down leaving the starter engaged continuously. (Starters are supposed to get the flywheel moving, then back out of position – disengage.)
Why does my golf cart make clicking sounds?
On a gas golf cart, the most common symptom is the starter failing to engage – so the engine doesn’t turn over – while all you hear a series of very futile clicking sounds.
Why does my solenoid wear out?
Like any switch that relies on wiring, the solenoid could also just wear out due to overheating. This might cause it to fail to retrieve the pinion gear.
What does a solenoid do when you turn the ignition?
Step by step, it looks like this: When you turn the ignition key, a small amount of electricity goes to the solenoid. The solenoid uses that small amount of juice to close two heavy-duty contacts that allows a large jolt of electricity to pass through the starter. The solenoid also sends a pinion gear forward, which is the device ...
Why do starter contacts wear out?
Secondly, the contacts could begin to wear out from overheating or exposure to high levels of current. This needs to be fixed right away if possible, because this causes continuous use of the starter. If not caught in time, the solenoid and the starter will both need replacement.
Why won't my solenoid click?
The solenoid might not be getting enough electricity to do its work – which could be caused by loose connections, a weak battery or the coil wearing out.