What Is Pureing A Golf Shaft
- Remove Grooves In Shaft. Pureing a golf shaft is necessary to restore its original condition and make it playable again. ...
- Put Pure Grains Into Shaft. Putting pure grains into your golf shaft can make a difference on the course. ...
- Run Heat Through Pureed Shaft. ...
- Install New Golf Club. ...
Full Answer
What does it mean to "pure" a golf shaft?
Pureing a golf shaft is when a golf shaft is taken out of the golf club, analyzed, and then placed back in at a strategic angle. Many golf clubs, when they come from a manufacturer, could have small imperfections in the shaft. This is not usually an issue, but for some players, it can be. Yes, this means there could be a scientific reason why six iron is your nemesis!
Does Puring a golf shaft really work?
Mar 06, 2022 · What Is Pureing A Shaft? Essentially, Briand explains, the idea of a golf shaft purying helps identify inconsistencies with one’s intended design; as such, an alternate design can be used to choose a golf shaft. Thus, it is only by ensuring that certain info is gathered that one can build the club most consistently and in an overall stable state.
How do you replace a golf club shaft?
Pureing a golf shaft is the process of removing grooves and putting pure grains into the shaft. It is then run through a heat source in order to soften the grains and remove any impurities. Finally, the new golf club can be installed. Remove Grooves In Shaft. Pureing a golf shaft is necessary to restore its original condition and make it playable again.
How to install a shaft in a golf club?
Jan 25, 2016 · SST PURE Shaft Alignment finds the most stable bending plane or “Neutral-Axis” of the shaft. SST claims that when the club head is installed in the proper orientation with the “Neutral Axis,” golfers will see improved consistency. …
What is club champion Puring?
0:052:04Club Champion - SST Puring - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what happens is it tries to bend around it and so it'll actually throw the club head in or out ofMoreSo what happens is it tries to bend around it and so it'll actually throw the club head in or out of plane. That you're trying to get back to square at impact.
What is prepping a golf shaft?
Shafts: Lightly sand shaft from tape to tip with 150 grit or finer sand paper to remove the polyurethane finish and all the paint. This operation is "prepping" the shaft and can be done by The GolfWorks (PREP).
What happens when you soft step a golf shaft?
Soft stepping is the term used to indicate changing flex of a taper tip shaft by adjusting the stiffness of a set of irons by putting the lower numbered iron shaft throughout the set. For example, the 8 iron shaft is put in the 9 iron, the 7 iron shaft in the 8 iron and so on through the set.Oct 4, 2013
What does shortening a golf shaft do?
1:403:54How Does Butt Trimming a Golf Shaft Affect Playability? - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst thing is if you cut in one inch off you shorten the beam of the club. Which physics will tellMoreFirst thing is if you cut in one inch off you shorten the beam of the club. Which physics will tell you that would make it stiffer. Although in a golf club.
How do you prepare the tip of a golf shaft?
0:445:49Golf Repair - How to Prep a Graphite Shaft Tip for Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow I typically use 180 grit sandpaper or 120 it's a little bit me this would be medium this wouldMoreNow I typically use 180 grit sandpaper or 120 it's a little bit me this would be medium this would be fun. And this ensures that we don't start to dig too far into the removal.
How do you tip a shaft?
1:0911:44The Purpose of Shaft Tipping - YouTubeYouTubeStart of suggested clipEnd of suggested clipSection we take away. The more we get into the more we expose this wider. Section from from here onMoreSection we take away. The more we get into the more we expose this wider. Section from from here on up. So we we take the soft part away we leave the stiffer part which is up in this butt. Section.
Should I soft step my iron shafts?
Regular flex shafts are easier to hit and are for slower swing speeds. Some players want to change their shafts to be between the two for their swing speed and style. Soft stepping golf shafts is a way to do this.Jun 30, 2020
Should I hard step my irons?
"Hard stepping" would make a shaft stiffer, "soft stepping," more flexible. The effective change in flex between immediate lofts from stepping is 1/3, or 5 cycles per minute, a practically negligible change in performance for most golfers.
How much should I tip my driver shaft?
The average tip on drivers is about an inch, although some players go to greater lengths. Back when Tiger Woods was using a 42.5-inch True Temper X-100 steel shaft in his driver, all of the extra length (more than three inches) was cut off the tip to achieve the proper flex.Mar 4, 2014
What happens if your golf clubs are too short?
What Happens When Golf Clubs Are Too Short? For most golfers, having clubs that are too short will be better than if they're too long, but can still result in inconsistent shots. Clubs that are too short will make you stand bent over, which can cause back pain. You'll also have the tendency to push the ball a lot.
Should short golfers use shorter clubs?
Since it is designated as a set for junior golfers, shorter golfers will benefit tremendously from the shorter clubs. If you measure between 5 feet 3 inches and 5 feet 8 inches, the length is perfect for you.Jan 9, 2022
Will shortening my driver help?
Shortening the shaft will make the club shorter but it will also make the shaft stiffer and adjust the swing weight as well. Plus, the more length you remove, the less flex your club will have. Depending on how much you cut it down, it could move a regular flex to a stiff or a stiff to an extra stiff.
How We Tested
For this test, we used two seemingly-identical six irons. The clubs had the same head, shaft, grip, loft, lie, length, swing weight, and total weight. The only difference was that one shaft has been SST PUREd and the other had not.
The Results
Our first myth is totally busted – PUREing a shaft led to significant distance increases.
Conclusion
The SST PUREing process is no placebo, it’s one of the most impactful technologies that we’ve ever tested. I entered this test as skeptical as anyone, but the data combined with my own firsthand experience proved that PUREing your clubs definitely leads to improved performance. You can expect the clubs in my bag to be SST PUREd from here out.
What is SST pure?
If you would like this service please call 1-800-848-8358. SST PURE Shaft Alignment, the leading golf shaft alignment technology on the PGA Tour and around the world, is available through The GolfWorks! SST PURE® identifies asymmetries ...
Can you align a screen logo on a golf shaft?
It is not possible to align screen logos on graphite or steel golf shafts that have received the PUREing process. PUREing may also result in screen logos not being uniform in location. This condition is a distinct indication that the golf clubs have been PUREd.
What is a Weiss-Gibson shaft puller?
The Weiss-Gibson Ultimate Shaft Puller makes club head removal as simple as 1 – 2 – 3. Let hydraulics do the work for you with this innovative new device designed to take time and effort out of club repair. The 4 ½-inch rubber clamp prevents slipping and does not mark shafts. Even first-timers can learn to extract club heads like a pro.
Why use SST Pure?
At their level, they simply cannot afford mis-hit shots caused by their equipment. SST PURE technology, which locates the most stable orientation of any golf shaft to minimize off-line bending and twisting, is now available to all golfers through a domestic and international network of licensees. If you are serious about your golf, u0003hit every shot SST PURE!
Who is Bob Dodds?
It is a must for all full-time clubmakers.” – Bob Dodds, former technical director of the Professional Clubmakers Society and former host of Golf Channel clubfitting show.
Is a golf shaft straight?
Golf shafts aren’t perfectly straight or perfectly round. Studies have shown that irregularities in a shaft’s structure cause off-line bending and twisting during the golf swing. This causes an increase in shot dispersion or, in irons, u0003inconsistent performance from club to club. The SST PURE® Shaft Alignment System analyzes the structure ...
YaBish86
Look there is a ton of confusing information out there about pured shafts and if it actually matters. If it did i would think that every tour player would have it done. I’ve seen claims of yardage increases and various other claims are there any truths to it?
cnosil
Been some discussion in this before.#N#Some say yes. some say no. Some say it used to work when shafts were not manufactured as well and had spines. Only way to tell would be to take club and pure it and capture numbers. Then turn the shaft into various orientations and capture more numbers.
CarlH
I did have my graphite iron shafts pured for my current set of irons that I ordered. Since I don't have before and after data to compare, I can't comment if it was worth the $$ or not. Here's what I do know....I don't have any doubts niggling in the back of my mind that maybe if I'd only done this....blah blah.
TR1PTIK
When I was still playing a Nike Vapor Pro driver, I purchased a different shaft and had it "pured". The club worked well, but not having anything to go off of, I don't know if it was worth the money. When I switched to my Ping G25, I purchased that same shaft without puring to try in the new head. It doesn't seem to be a good match for me at all.
perseveringgolfer
Maybe there's a difference because of the shaft's alignment, but more than likely t he difference comes from the vastly different driver head.
