In essence, the ignitor works to improve the quality of electrical signals and to provide a greater flow of energy to the coil, which in turn assists your spark plug in operating properly. Thus, it is a necessary component on gas-powered golf carts, but it is rarely present on electric golf carts because there is no need for it.
What does ezgo ignitor do?
EZGO Ignition Switch, Ignitor, Coil Parts Ignition coils transfer voltage from your battery into spark for your engine to fire. We carry ignition coils for EZGO TXT, RXV, Marathon, and ST350 Workhorse golf cart models.
What does an ignitor do on a golf cart?
The ignitor boosts the signal and sends it to the ignition coil. The coil then creates the large spark that goes to the spark plug and fires the gas mixture in the cylinder. Ignitors can be the cause of a weak spark or they may fail completely and then the coil cannot create any spark at all.
What does an ignitor do?
The ignition ignitor is the component that is responsible for sending a signal from the key's ignition switch to the electrical system to supply power to the spark plugs and start your engine.
How do I test my EZ Go golf cart Ignitor?
Take the voltmeter's black and red probe and place it on the –ve and +ve terminal of the coil. Take the readings. It should be between 3.7-5.2 ohms. If outside the range, the coil should be replaced.
What would make a gas golf cart not start?
First, try this: turn the key switch on, hit the accelerator, and check for a clicking noise. If you don't hear clicking, it's time to take a look at your cart's batteries. Make sure the battery is fully charged and the terminals are cleaned and secure. Next, see how the water level in the battery is holding up.
Why does my golf cart have no spark?
If there is no spark, unplug the white plug with blue and black wires that are at the bottom of the engine under the valve cover. Check for spark once again. If there is a spark, the coil is in good condition and the ignition kill relay or its wiring is at fault.
How do you know if your ignitor is bad?
Here are a few indications that you have a faulty ignitor.No Cold Air. ... The Furnace Won't Come On. ... The Furnace Suddenly Stops Blowing. ... Starts, Then Stops, Then Starts Again. ... Tripping the Breaker More Than Once. ... I Hear the Click, But Nothing Happens. ... Flame Sensor Problems. ... Short Circuit.More items...•
What are the symptoms of a faulty ignition module?
a faulty ignition module can affect ignition timing, resulting in an engine that misfires and runs rough. the engine may also run well at low speed, but won't accelerate well. 3. stalling: a failing ignition module can occasionally prevent the engine from getting spark, causing it to stall.
How do you test a spark igniter?
1:052:23Lennox # 73K38 - Continuity Test (Gas Furnace Ignitor) - YouTubeYouTubeStart of suggested clipEnd of suggested clipAlso set the dial to the lowest ohms of resistance to test for continuity take the probe from theMoreAlso set the dial to the lowest ohms of resistance to test for continuity take the probe from the multimeter. And touch it to one of the terminals. Now touch the second probe to the remaining.
Where is the igniter on a ezgo gas golf cart?
0:001:15EZGO igniter location - YouTubeYouTubeStart of suggested clipEnd of suggested clipNot the ignition coil which is that right here igniter it's underneath this cover right here. ThisMoreNot the ignition coil which is that right here igniter it's underneath this cover right here. This is the cover but to get to it you need to remove the battery.
Why does my ezgo golf cart not move?
The main reason why a EZGO gas golf cart will not go forward is because of a locked up brake, or a faulty solenoid and accelerator. A defective Run/Tow or Forward/Reverse switch can also cause a EZGO to not move forward.
How do you test a golf cart ignition coil?
Attach the red lead to the positive terminal. Select the "Ohm" setting on your volt/ohm meter and read the display. The golf cart coil should register as more than 3.7 ohms, but less than 5.2 ohms. If the coil registers outside this range, replace the coil with a new unit.