Full Answer
What is a whipping on a golf club?
This would be the equivalent of the hosel area on today’s modern clubs. The whipping acts both a joint stabilizer as well as providing a finished appearance. This is an “old school” manual hand process, but at Better Golf Shot, we do replace old brittle and frayed whipping. Turnaround time is usually one day.
How long does it take to replace whipping on a club?
This is an “old school” manual hand process, but at Better Golf Shot, we do replace old brittle and frayed whipping. Turnaround time is usually one day. The wooden club shown on the left is without whipping.
Do Your hickory golf clubs have “whipping”?
If you have older Hickory true wooden clubs from the early days of golf up through the 1980’s – the clubs likely have what is termed “whipping” over the joint where the club shaft (wood or steel) meets the club head. This would be the equivalent of the hosel area on today’s modern clubs.
How did golf clubs get so widely used?
As the sport of golf developed, a standard set of clubs began to take shape, with different clubs being fashioned to perform different tasks and hit various types of shot. Later, as more malleable iron became widely used for shorter-range clubs, an even wider variety of clubs became available.
Are golf club ferrules necessary?
Does Every Club Need Them? Almost all modern clubs are designed to require a ferrule. Any club that has a clubhead with a neck that ends abruptly, almost all clubs have this, require a ferrule. Some older clubs have a tapered neck which means they fit the shaft in a really flush way.
When did they stop using wooden shafts for golf clubs?
Hickory became the standard material for golf club shafts until steel shafts were introduced in about 1925 in the US, and became standard everywhere from the mid 1930s. They had the advantage as they did not break like the hickory shafts and could be produced reliably with uniform feel in matched sets.
Are 60 year old golf clubs worth anything?
Many clubs produced as recently as the 1950s and '60s are considered "classics." Some are worth $1,000 a set, and the right kind of sand wedge can bring $500 or more all by itself.
How can you tell if a golf club is vintage?
Common golf clubs can be identified by these traits:Aluminum caps on the end of the handles.Nickel, chromed or stainless steel heads.Dots, lines, hyphens or other face scorings.Stamps on the back for yard ranges.Phrases on the back such as accurate, superior, aim-rite, and other common sounding names.
When did golf clubs get metal shafts?
1925The first few decades of the 1900's saw a lot of experimentation and innovation in the club design. Around 1925 the steel shaft was introduced in the United States, although blacksmiths had experimented with them since the late 1890's.
When did they stop using hickory shafts?
1935With the arrival and eventual legalization (1929) of steel shafts, the demand for hickory's started to diminish, by 1935 the production of hickory clubs had stopped.
Are 20 year old irons too old?
There is no evidence that golf clubs deteriorate over time. Well maintained clubs will last a lifetime. 10+ year old clubs should be checked for better options but clubs less than 5 years old do not need replacing except for wear and tear issues to which wedges and forged irons are most vulnerable.
Do irons lose distance over time?
As we mentioned, truly worn out irons can be hard to come across, it would take me back to the days of using my dad's old clubs that were well past their sell by date. However, if you have truly worn your clubs out, you can lose about 7-10 yards on them.
What is the hardest club to hit in golf?
A 1-iron is the hardest iron to hit because it is the longest and has the lowest loft of between 14° and 16°. The rise of hybrid clubs to replace long irons however means in the modern game 1-irons and 2-irons are very rare indeed resulting in 3-irons and 4-irons in reality being the most difficult irons to hit.
What are the most valuable vintage golf clubs?
What Are The Most Valuable Vintage Golf Clubs?Long Nosed Scraped Golf Club: this vintage club was sold at a Sotheby's auction in 2007 for $91,000.Square Toe Light Iron Golf Club: this club was auctioned at the Sotheby's 2007 auction for $151,000.More items...
Does anyone want old golf clubs?
There are plenty of places to donate your unbroken used equipment. Charitable organizations such as Goodwill, The Salvation Army, Savers, and a host of others accept such equipment and sell them in their stores.
What golf club is a niblick?
9-irons16. Pitching Niblick – this is the old way to refer to a golf club which achieved the same function as the modern 8-iron, or short iron. 17. Niblick – the old name for a sort of golf club which corresponds to the 9-irons golfers around the world use nowadays.
What were the names of the golf clubs after World War II?
The traditional names of the clubs, like “niblicks” and “spoons”, were replaced by the standard numbering system used to this day. There was little development and advancement for the next few decades. After World War II development of golf clubs were influenced by research into synthetic and composite materials.
When did the R&A golf club come out?
Around 1925 the steel shaft was introduced in the United States, although blacksmiths had experimented with them since the late 1890’s . The R&A, named from The Royal and Ancient Golf Club of St Andrews, is the governing body of the game of golf.
What wood is used for golf clubs?
Hickory quickly became the standard wood of choice for club-makers due to its availability and better durability. In 1848 the “guttie” ball was introduced by Rev. Adam Paterson, which quickly made the “longnoses” or drivers obsolete. Bulgers emerged to replace the longnoses which had a bulbous head, resembling modern woods.
How many clubs can you carry in a golf bag?
Up until 1939 it was common for a golfer to carry 20-30 clubs in their bag. However with the advancement of the steel shafted clubs the R&A introduced the 14 club rule in 1939, which limited players to only be allowed to carry 14 clubs. The traditional names of the clubs, like “niblicks” and “spoons”, were replaced by the standard numbering system used to this day.
What were the clubs made of in the 1500s?
In the 1500s a set of clubs consisted of: a set of play clubs, “longnoses”, for driving; fairway clubs or “grassed drivers”, for medium range; “spoons” for short shots; “niblicks” similar to wedges; and a putting “cleek”. These golf clubs were made up of wood with the shafts being made from ash or hazel and the club heads being made ...
What is the evolution of golf?
The Evolution of the Golf Club. Since the inception of the game of golf, players have continually tried to improve upon their equipment. The earliest golf clubs were initially carved by the golfer themselves and typically out of wood. Golfers soon turned to skilled craftsmen to produce higher quality equipment.
What is the R&A golf club?
The R&A, named from The Royal and Ancient Golf Club of St Andrews, is the governing body of the game of golf. The R&A finally legalized the use of steel shafted clubs after the Prince of Wales used them on the Old Course at St Andrews in 1929. The steel shaft provided for greater accuracy and durability.
Who said there are too many clubs in the bag?
In one of the more curious rules violations in major championship history, Woosnam had just moved into a share of the lead when, as Peter Shuttleworth of BBC Sport wrote, "Byrne, the recently appointed caddie, then uttered those fatal words that will haunt Woosnam for the rest of his days: "There's too many clubs in the bag."
Did Tiger throw his club?
Technically, Tiger didn't throw his club. He did, however, give it a healthy boot. The incident was evidence of two things: Woods' disgust with his own inability to execute in majors, and the golfer's total disregard for decorum when he's upset...even at the Cathedral of Golf. His tantrum on the 16th was presaged by a loose shot and customary profane outburst on the previous hole.
Is Michael Phelps a good swimmer?
It's quite safe to say that Michael Phelps is a much better swimmer than he is a club thrower. This left-handed overhead toss on The Haney Project displayed the Olympian's inexperience in the finer points of on-course emotional outbursts.
Why is the Allan Lard golf shaft called a whistling shaft?
To reduce its weight, it was drilled with hundreds of small holes. The perforations helped enhance club head speed and reduced torque significantly. When swung, these holes caused a whistling sound, hence the "Whistler" nickname. But like the other steel shafts, they never caught on. Allan Lard's perforated steel shaft.
What wood was used for golf shafts in the 17th century?
The golf shafts in the 17th and 18th centuries were not yet made of hickory, but rather from ash and hazel or whatever hardwood was available locally including wood from trees such as danga wood, ironheart, purpleheart, greenheart, bloomahoo and bulletwood. The US used other woods from what was being used in Great Britain, ...
Why are Spalding clubs painted tan?
The clubs had steel shafts which were painted tan to give the impression of hickory. This practice was also done by other. manufacturers to help influence golfers to make the transition from hickory to steel. Spalding's steel shaft, painted to look like hickory.
What is a whistler shaft?
Nicknamed the "Whistler", Lard's shaft was made from a solid steel bar that was bored out and milled to form 6 sides. To reduce its weight, it was drilled with hundreds of small holes.
What wood was used for the club heads?
The US used other woods from what was being used in Great Britain, including ash and lancewood. Club heads were made from tough woods such as beech, holly, apple and pear. These were connected to the shaft using a splint and then bound using leather straps.
What is Spalding's shaft?
Spalding's steel shaft, painted to look like hickory. It was not until some advances were made in the raw steel material and new manufacturing processes were developed, enabling the production of a stepped-down shaft, that steel started showing signs of becoming a clear favorite.
When did steel shafts become legal?
In 1924, the USGA finally legalized steel shafts, although the R&A continued to ban them until the Prince of Wales used a set at St. Andrews in 1929 which helped force a rule change. In 1924, the first steel shafts were allowed in the US Open, They were allowed in putters only. The winner, Cyril Walker, used one.
How many times should I wrap a golf club shaft?
Wrap around the shaft about 5 times over the end to keep it secure. Now, continue wrapping by using your right hand to guide the whipping while the left hand twists the club head to rotate the shaft in the clamp/vise. Continue wrapping the whipping tightly until you are about five wraps from the end.
How to use a rubber golf club?
First put your club in a rubber golf club clamp and gently tighten so that the club is secure but can still be spun easily in the club. This is important to make winding the whipping easier. Next, grab your whipping. You can remove and reuse the old whipping or you can use new whipping.
Feedback
Hi I have a bunch of modern woods that will need there whippings replaced after restoration (Mizuno and Ping) and want some thing as close to original as possible. Does anyone know what the thread was used on them? I know it is not linen but more of a nylon or polyester. Any ideas on a supplier in the UK would be greatly apreciated too
Feedback
Many thanks Kelso that is the sort of stuff I am after. Charley I wish we had the surplus of clubs over here to break down for parts but alas we dont, our charity shops dont take in sporting goods as there is no market for them, ebay does have wooden clubs but with the postage as high as it is also makes it a no go. Many thanks Chris
Feedback
Rather than sully up a couple of threads currently running, thought I'd resurrect this one. I've been using the Crawford Threads Ltd. Linen (18) Thread, 4 Cord, 50 grams on a couple of hickory's. An easy to use waxed linen thread. While it looks fine on those, not so much on persimmon clubs that are more contemporary (i.e MT 693T 3W).
Feedback
Rather than sully up a couple of threads currently running, thought I'd resurrect this one. I've been using the Crawford Threads Ltd. Linen (18) Thread, 4 Cord, 50 grams on a couple of hickory's. An easy to use waxed linen thread. While it looks fine on those, not so much on persimmon clubs that are more contemporary (i.e MT 693T 3W).
Feedback
The aforementioned waxed linen thread works good. Has some tack to it so as one proceeds, the thread stays in place Just to thick of a finished look. And the unwaxed variety easily comes unwound unless you keep constant pressure while wrapping (PITA). Never had whipped a club before until two weeks ago. A bud showed me how.
Feedback
Thanks Wrigs, and for the pic. Obviously didn't get the right kind of thread when there. But was sort of out of my element, asking the ladies about thread to wind golf clubs with. They didn't really know what I was talking about. LOL.
Feedback
Your post triggered a memory Randy. Bought a Heathkit tube amp kit from a H.S. buddy that never got around to building it. Needed a stereo rig on the cheap (not unlike golf clubs). Heathkits had great "how-to" assembly instructions. Little soldering, put it together. Never could get it to stop "humming". Really was annoying.
What was the Whipping of Slaves?
Whipping of Slaves. The law provided slaves with virtually no protection from their masters. On large plantations this power was delegated to overseers. These men were under considerable pressure from the plantation owners to maximize profits. They did this by bullying the slaves into increasing productivity. ...
Why did Elizabeth Keckley get whipped?
However, he arranged for her to be whipped in order to subdue what he called her "stubborn pride".
Who laid on the stripes?
The Negroes from the neighbouring plantations were summoned to witness the scene. A powerful blacksmith named Hewes laid on the stripes. Fifty were given, during which the cries of my father might be heard a mile away, and then a pause ensured.
How did the slaves punish the poor?
The usual mode of punishing the poor slaves was, to make them take off their clothes to the bare back, and then tie their hands before them with a rope, pass the end of the rope over a beam, and draw them up till they stood on the tips of their toes. Sometimes they tied their legs together and placed a rail between.
