Golf cart drive belts are designed to last at least 4 years of normal use or around 90,000 miles. They’re durable and resistant to damage, so you shouldn’t need to replace a golf cart belt very often, particularly if you’ve purchased a new cart. However, on older carts that have been well used, you might decide that it’s time to replace the belt.
Full Answer
How do you tighten the drive belt on a Yamaha golf cart?
0:002:03How to tighten a loose Starter Belt on Yamaha Golf Cart YDRA. G29YouTubeStart of suggested clipEnd of suggested clipAll right my 12 mil uh socket here grab that loosen that up 17 mil wrench here wrap this down. ThereMoreAll right my 12 mil uh socket here grab that loosen that up 17 mil wrench here wrap this down. There you go.
How do you put a drive belt on a Yamaha golf cart?
0:152:32HOW TO CHANGE A DRIVE BELT ON YAMAHA GOLF CART ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust put the lever in front halfway from reverse and forward. Once it's in reverse and you can spinMoreJust put the lever in front halfway from reverse and forward. Once it's in reverse and you can spin the back off.
How do you change a drive belt on a 2007 Yamaha golf cart?
0:462:46Yamaha Drive Belt | How to Install on G29 Golf Cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow to wet do this on the back clutch or the secondary clutch take the belt and slowly lay it overMoreNow to wet do this on the back clutch or the secondary clutch take the belt and slowly lay it over the top of this outer chief like this just slowly roll it over. And. It will come right.
How tight should the drive belt be on a golf cart?
The reason for a Club Car drive belt being too tight can be because the drive belt is too small for the golf cart. The way to check if the belt is fitted correctly is to push the belt down with one finger at the center between the clutches. It should not deflect more than 1.5inches. It should not be less as well.
What is a drive belt in a golf cart?
The golf cart drive belt is the larger (1" to 1 3/16" wide), longer and usually looser belt on gas golf cars. It connects the drive clutch (on the engine) to the driven clutch (on the differential) and transfers the power of the engine to the rear wheels.
How wide is a Yamaha golf cart belt?
1-3/16″ wideBelt size is 1-3/16″ wide x 39″ long.
How do you install a secondary clutch on a Yamaha golf cart?
6:1216:27Yamaha Drive G29 and Drive 2 Clutch Kit Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut i have seen a lot of guys just make something with stuff that they have laying around the garageMoreBut i have seen a lot of guys just make something with stuff that they have laying around the garage. Now it can be as simple as just using a piece of angle iron. And a piece of all thread.
How does a golf cart clutch work?
0:463:28How a golf cart CVT slip drive clutch works - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd the rear drive clutch actually separates it widens causing the belt to drop down into the clutchMoreAnd the rear drive clutch actually separates it widens causing the belt to drop down into the clutch.
How do you remove a starter from a Yamaha golf cart?
How to Remove, Wire & Test a Golf Cart Starter Generator Disconnect the negative battery cable. Loosen and then remove the top and bottom bolts of your starter generator. Remove the belt of your starter generator and leave it around the engine. Loosen all of the wiring and remove them each by hand.More items...
How do I know if my golf cart belt is bad?
0:152:00How to Check the Belts in your Gas Golf Cart | Golf Cars UnlimitedYouTubeStart of suggested clipEnd of suggested clipDown below and you don't want to press the moderate pressure on that belt you're gonna want to seeMoreDown below and you don't want to press the moderate pressure on that belt you're gonna want to see about 3/16 to 1/4 inch of deflection. There no more than that that'll be your proper.
How do you measure golf cart belts?
0:002:04How to measure for a go-kart drive belt. - YouTubeYouTubeStart of suggested clipEnd of suggested clipCover. Now the first measurement we're going to take on this is we're going to measure from theMoreCover. Now the first measurement we're going to take on this is we're going to measure from the centerline of the crankshaft. To the centerline of the jack shaft.
How do you tighten a clutch belt on a Club Car golf cart?
Slide the old drive belt off the front drive clutch pulley, and then the rear clutch pulley. Slip the new belt around the golf cart's clutch pulley, and then stretch it out over the front pulley. Pull the front pulley forward slightly to increase the belt tension, and then tighten the tension bolt with the wrench.
How do you install a secondary clutch on a Yamaha golf cart?
6:1216:27Yamaha Drive G29 and Drive 2 Clutch Kit Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut i have seen a lot of guys just make something with stuff that they have laying around the garageMoreBut i have seen a lot of guys just make something with stuff that they have laying around the garage. Now it can be as simple as just using a piece of angle iron. And a piece of all thread.
How do you tighten the belt on a Club Car golf cart?
Slide the old drive belt off the front drive clutch pulley, and then the rear clutch pulley. Slip the new belt around the golf cart's clutch pulley, and then stretch it out over the front pulley. Pull the front pulley forward slightly to increase the belt tension, and then tighten the tension bolt with the wrench.
How do I replace the belt on my electric golf cart?
Answer provided byFirst, raise the golf cart engine cover to access the drive belt inside the engine compartment. ... Next, loosen the drive belt tension bolt with an open-end wrench on the front pulley. ... Finally, pull the front pulley to increase the belt tension. ... MORE: Average car insurance cost in 2021.
How do you remove a starter from a Yamaha golf cart?
How to Remove, Wire & Test a Golf Cart Starter Generator Disconnect the negative battery cable. Loosen and then remove the top and bottom bolts of your starter generator. Remove the belt of your starter generator and leave it around the engine. Loosen all of the wiring and remove them each by hand.More items...