Golf-FAQ.com

where do the coil wires go on a golf cart

by Akeem Keebler Published 2 years ago Updated 2 years ago
image

The location of the pulser coil is under the cart’s seat and is near the engine. It is better to use a user manual to locate the coil so that it can be tested or replaced. If there is no spark, there is always a requirement to check if the coil is working fine.

Full Answer

How do you find the ignition coil on a golf cart?

Locate the ignition coil in the golf cart by getting the seat of the golf cart raised to, as would be mentioned in the owner’s manual. It is shaped cylindrically with a metal sink on both sides. It will have a thin, wire coming out from one end and another wire, a relatively thicker one from the other end.

How do you hook up a golf cart ground wire?

Here are some steps to help you get started: Always attach your ground wire to the frame, negative post on your solenoid, or the negative post of a 12 Volt battery. For gas and electric golf carts with 48 volts, always connect your ground wire to either the frame or the negative terminal on their controller.

Where is the solenoid on a golf cart?

Most golf cart solenoids will be found under the seat with four wires connected to it. It should look like this. So now that you found your solenoid, it’s time to find out if it needs replacement. The first step will be disconnecting the high side wires.

Where is the pulser coil on a golf cart?

The location of the pulser coil is under the cart’s seat and is near the engine. It is better to use a user manual to locate the coil so that it can be tested or replaced. If there is no spark, there is always a requirement to check if the coil is working fine. Use a grounded HEI model and mount it properly in the place.

image

Where does the wire go to a coil?

0:203:01Wiring an external battery coil to your engine - YouTubeYouTubeStart of suggested clipEnd of suggested clipYour negative directly to your points contact. When I say directly to your points contact you'reMoreYour negative directly to your points contact. When I say directly to your points contact you're going to have a wire coming out of your points connector box that wire tells the coil when to fire.

What are the terminals on a ignition coil?

In the case of a conventional cylinder ignition coil, the electrical connections are designated as terminal 15 (voltage supply), terminal 1 (contact breaker), and terminal 4 (high-voltage connection). The primary winding is connected to the secondary winding via a common winding connection to terminal 1.

What would cause a gas golf cart not to fire?

Check the area for loose wires or any broken pieces. You'll also want to look at your forward and reverse switch, which is also prone to wearing out after long-term use. This is an easy fix — replacing the forward/reverse switch is a generally inexpensive and quick repair.

Why does my golf cart have no spark?

If there is no spark, unplug the white plug with blue and black wires that are at the bottom of the engine under the valve cover. Check for spark once again. If there is a spark, the coil is in good condition and the ignition kill relay or its wiring is at fault.

How is a coil wired?

2:073:22Coil Induction & Wiring Diagrams - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe magnetic field actually induces the voltage in the secondary. Drawing. Actual electrons from theMoreThe magnetic field actually induces the voltage in the secondary. Drawing. Actual electrons from the tip of the spark plug to the positive side of the engine electrical.

Is there a positive and negative on a coil?

The polarity of the coil should match that of the battery by connecting it so (+) goes to (+) and (-) connects to (-). But don't worry about which way you install the battery (positive or negative ground) or which way you install the coil (regardless of coil markings) it will automatically adjust itself.

How do you test a golf cart coil?

Take the voltmeter's black and red probe and place it on the –ve and +ve terminal of the coil. Take the readings. It should be between 3.7-5.2 ohms. If outside the range, the coil should be replaced.

What would cause a golf cart not to run?

As the main source of power to your electric golf cart, the batteries are commonly the cause for why your electric golf cart won't start. Acid-based batteries are typically used for electric golf carts and must be recharged in order to work properly.

How do you fix a golf cart that won't move?

The problem could be with either the Run/Tow switch or Forward/Reverse switch or both. Check the switches to ensure that they aren't stuck midway. If they are, getting them released should help. However, if they show signs of wear and tear, you must get them replaced.

How do you test a golf cart Ignitor?

Testing Your IgnitorPark your cart and put bricks behind the wheels to keep it from moving.Open up your cart engine and attempt to identify the ignitor using your cart engine schematic.Trace the ignitor back to the pulsar to see where they are connected together on your cart.More items...

What does a pulser coil do?

A Pulser coil is used for Generation of pulse (spark) to initiate the ignition of a vehicle. The Pulser Coil is an important component in an engine's timing & ignition system.

How do you check for spark on a golf cart?

0:4816:08Got Burned...by a GOLF CART?!? (EZ-GO No-Start) - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou just plug in a test light instead of the ignition coil just to check if we have power andMoreYou just plug in a test light instead of the ignition coil just to check if we have power and control so we expect a blinking test light when we crank the engine. Over.

What side of a coil is positive?

Crank the engine over (do not start it) and the needle of the voltmeter should show an upward swing to the plus or positive side (do not worry about taking a reading). If volt the needle swings down to the negative side and gives a negative reading, your coil is hooked up backwards.

How many terminals does a coil have?

There are many different wiring configurations for such coils. They may have one or two primary terminals (or wires), and one or two secondary terminals (or wires).

Does it matter which way an ignition coil is wired?

If it is a pure coil with no electronics or diodes etc, then it shouldn't matter which way around it is connected. Traditionally you get a better spark with a negative polarity (i.e. negative HT voltage w.r.t. ground), since it's easier for a spark to initiate from the hotter centre electrode.

What is SW and CB on an ignition coil?

SW stands for switch. The contact breaker is CB. The negative wire went to the SW terminal when cars were positive ground.

What is the purpose of a golf cart pulser coil?

The purpose of the Pulser coil is to give ignition signals to the engine and ignition system. The resistance categorizes pulser coils.

How to remove coil from flywheel?

To remove the coil, the flywheel needs to be detached. Use a balance styled puller and attach the same to the threaded holes. Now add some pressure and let the puller do its job by removing the flywheel.

How to adjust a pulser coil?

The screws should be attached centrally. To adjust the coil stability, replaced the coil wire or the coil. Switch the coil wires to adjust the pulser.

Where is the pulser coil located?

The location of the pulser coil is under the cart’s seat and is near the engine. It is better to use a user manual to locate the coil so that it can be tested or replaced. If there is no spark, there is always a requirement to check if the coil is working fine.

Is the Ping G25 adjustable?

Is the Ping G25 driver adjustable? The Ping G25 driver is adjustable. It’s possible to do four adjustments using the hosel adapter of the driver apart from the stated loft setting and...

What is a golf cart?

Golf carts are also known as golf cars. The term "cart", in its purest sense, refers to a vehicle that does not travel under its own power. Golf cars, however, are most commonly referred to as golf...

When did golf carts evolve?

Club Car Golf carts have evolved many times since 1975, and although the basic electrical design has stayed close to the same, there are small differences. These differences are important when troubleshooting your cart.

What is a golf cart go switch?

On your golf cart, this high powered circuit is either your ignition on a gas golf cart or your electrical motor power circuit for an electric golf cart. Basically it’s your golf cart’s go switch, and it’s absolutely essential to your golf cart’s ability to do its job. Golf cart solenoids are also typically one of the first components ...

What is the most important part of a golf cart?

One of the most important components of your golf cart is the solenoid. It is one of the main components of your golf cart that allows it to move. Whether you have a Yamaha, E-Z-GO, or Club Car golf cart, and no matter if it is an electric or gas golf cart, you need a properly operating solenoid to get anywhere. Contents [ show]

Why does my golf cart have no solenoid?

Golf cart solenoids are also typically one of the first components to fail in your golf cart, because they work very hard, turning on and off every time you stop and go in your golf cart. If you have an issue with no start or no go then your solenoid should be pretty high on your list of things to check.

What happens if a solenoid reads infinity?

If it reads infinity or open lead, then the solenoid has an internal fault and requires replacement. Your solenoid should also have a range that it operates in, and if the resistance reads outside of that range, you should replace the solenoid even if it works to avoid damaging other components.

What is a solenoid on a golf cart?

A solenoid, for our purposes, is a type of relay. A relay is a type of switch that uses a low power circuit to operate a high power circuit. A solenoid uses a magnetic coil (the actual solenoid) on a low power circuit to push a rod that closes a high power circuit. On your golf cart, this high powered circuit is either your ignition on ...

What to do if your solenoid doesn't work?

Before you run out and get a solenoid, you’ll have to test the entire ignition system this way to find out what’s not working, and it is a bit of a pain.

What is a micro switch on a gas pedal?

This switch is what sends the low power to the solenoid. The solenoid uses this to create a circuit between the battery and the starter, thus starting your motor and getting you grooving.

Why do golf carts have solenoid?

The solenoid is simply there to allow electricity to flow freely to the controller and motor which will result in a running golf cart. RELATED: 4 Signs you need to Replace your Golf Cart Batteries.

How to check if a golf cart solenoid is silent?

On an electric golf cart, if the solenoid is silent – no clicking – use the setting voltmeter to DC volts using the 200 range. First, turn on the ignition while looking for a reading on the smaller terminals. If nothing is appearing, then press on the accelerator. If the needle doesn’t move, then the problem is not with the solenoid.

Why is my golf cart not clicking?

On an electric golf cart, the most common symptom is the solenoid is not delivering electricity to the controller when the vehicle’s ignition is turned on. In normal operating conditions, the solenoid clicks on and off with the ignition switch. A failing solenoid will generally not click. Two things could be going on here.

What does it mean when a golf cart solenoid goes bad?

Technically, in fact, a solenoid is a shape – a shape in which the length of something coiled is longer than the diameter of the coils. In engine starters, this refers to the smaller motor ...

What does a solenoid do when you turn the ignition?

Step by step, it looks like this: When you turn the ignition key, a small amount of electricity goes to the solenoid. The solenoid uses that small amount of juice to close two heavy-duty contacts that allows a large jolt of electricity to pass through the starter. The solenoid also sends a pinion gear forward, which is the device ...

Why do you use electrical tape on a solenoid?

When you do this, use electrical tape to seal the cable ends, so they won’t form a circuit by accidentally touching each other or connecting through a metal conductor inadvertently. Doing this will ensure the vehicle will not run while testing the solenoid.

Why won't my solenoid click?

The solenoid might not be getting enough electricity to do its work – which could be caused by loose connections, a weak battery or the coil wearing out.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9