Golf-FAQ.com

where is the accelerator microswitch located on a fairplay golf cart

by Evelyn Ledner Published 2 years ago Updated 2 years ago
image

In a golf cart, you're going to find a large number of these switches throughout its build. For example, there is a micro switch located on the accelerator pedal. This switch activates when you push the pedal and sends a signal to the solenoid.

Where is the accelerator micro switch on a golf cart?

Refer to the user manual of your golf cart and locate the position of the accelerator micro switch. In most of the EZGO models, it is located on the bottom side of the cart near the accelerator pedal. Unscrew the outer covering and access the two terminals of the micro switch.

What is a microswitch on a golf cart?

As the name implies, a microswitch is a small switch. Microswitches are used in many golf cart applications. They are used at the accelerator pedal to provide a signal to the solenoid that you have depressed the pedal and are ready to go.

What happens when a micro switch goes bad on a golf cart?

A defective micro switch disturbs the overall power flow in the golf cart. A faulty micro switch leaves the nearby components damaged due to a low or unrated power supply. A dislocated micro switch can disturb the normal operation of other components.

How does a gas golf cart start?

In gas golf carts, a micro switch located on the accelerator pedal triggers a signal that will start the cart’s engine. The cart will run without any problem as long as this micro switch remains active.

image

How do you test a golf cart microswitch?

Using a jumper wire, jump the power from the 48V positive terminal to the small positive terminal on the solenoid. Turn the key of the cart to the ON position and press the accelerator. Check if the wheels are turning normally. If the wheels aren't turning, recheck the jumper connections and try steps 3 and 4 again.

What is a microswitch in a golf cart?

Microswitches are used in many golf cart applications. They are used at the accelerator pedal to provide a signal to the solenoid that you have depressed the pedal and are ready to go. In an electric golf cart, the solenoid sends power to the controller to move the cart.

How do you fix a golf cart accelerator?

Open up your cart hood and find the wires connected to your controller. Check to make sure each of these wires is properly screwed down and held in place. Inspect all other wires throughout your engine and accelerators. Tighten the connections on these wires to ensure that they run smoothly.

How do you test a micro switch on a gas golf cart?

Again, leave your black probe on the battery negative terminal and use your red probe for testing. With the key switch ON, you should read battery voltage at the common terminal (C or COM), but not the other terminal. Once the micro switch is activated, you should read voltage on both terminals.

What is the MCOR on golf cart?

Club Cars use an MCOR throttle device. This translates your foot movement at the pedal into electric impulse that the motor controller reads. MCOR stands for "Motor Controller Output Regulator".

How does a micro switch work?

Micro Switches have an actuator which, when depressed, lifts a lever to move the contacts into the required position. Micro switches often make a “clicking” sound when pressed this informs the user of the actuation. Micro switches often contain fixing holes so that they can be easily mounted and secured into place.

Why does my golf cart click but not move?

A Club Car golf cart can start clicking but not move, due to dust accumulating inside the battery ports. Opening the battery ports and checking whether there is any dust accumulation can tell you if this is the case. Cleaning it thoroughly with a cloth can resolve the problem.

Why does my gas golf cart not move?

A EZGO golf cart may not go forward or reverse because of a malfunctioning microswitch, solenoid, or ignition switch. Loose or corroded cable connections or a faulty controller can also cause the golf cart to not move.

What causes a gas golf cart to stop running?

Your golf cart may stop frequently while running in case of a faulty spark plug, defective TCI/carburetor, or improperly seated internal baffles and airbox lid. Sometimes, an empty or close-to-empty fuel filler, low battery charge, a binding linkage, or a bad fuel pump can cause a golf cart to stop running.

How do you test a gas solenoid on a golf cart?

Set your multimeter to ohms and insert a probe on each large terminal with the key off and the cart direction switch in the neutral position. Press on the accelerator with the cart's movement control in the forward position, and the key is turned on. A click should be heard first from the solenoid.

Where is the solenoid located on a golf cart?

0:095:38Replace Solenoid in Golf Cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipCart um your solenoid could be located in a bunch of different places but almost always underneathMoreCart um your solenoid could be located in a bunch of different places but almost always underneath the seat.

What is a microswitch?

As the name implies, a microswitch is a small switch. Microswitches are used in many golf cart applications. They are used at the accelerator pedal to provide a signal to the solenoid that you have depressed the pedal and are ready to go. In an electric golf cart, the solenoid sends power to the controller to move the cart.

What is a golf solenoid?

In an electric golf cart, the solenoid sends power to the controller to move the cart. In a gas golf cart, the solenoid sends power to the starter/generator to start spinning the engine. Microswitches also serve a purpose as part of the forward and reverse direction selector switch on many golf carts. In this application, they can be used ...

Why is my golf cart not accelerating?

When your electric golf cart does not accelerate, the first thing you need to keep in mind is that it is not a regular vehicle like your car . That's why the methods and solutions you use to get your car to start are not the same as the solutions you can apply to your cart.

Why is my golf cart speed controller not working?

There are many reasons behind a speed controller malfunction. The most common problem that happens in the controller has aged due to infrequent use. These are just some of the issues that could be affecting your vehicle's acceleration. If you have trouble finding the issue of your golf cart accelerator, don't be afraid to take it to the mechanic.

How does a golf cart solenoid work?

The golf cart speed controller and solenoid are both controlled by the accelerator. The pedal is connected to the potentiometer. That means when you are pressing the pedal for acceleration, you are actually going through the potentiometer by pushing a rod. The potentiometer works as a communicator and tells the speed controller how much voltage it ...

What happens if your golf cart doesn't accelerate?

Bad Solenoid. If your golf cart does not accelerate, there is a possibility of the damaged solenoid. The solenoid is basically an electrical switch that enables the battery's flow from the battery into the motor. Check out the signs of the bad solenoid.

What is a speed controller?

Speed Controller. The speed controller manages the speed of the golf cart. There are some situations when the speed controller fails, but the cart will still start and move ahead. But, as it runs for a while, it will start malfunctioning.

How does a potentiometer work?

The potentiometer works as a communicator and tells the speed controller how much voltage it has to consume. The more voltage means the more speed and vice versa (Check out our resource on golf cart speed ).

What is a microswitch?

As the name implies, a microswitches is a small switch. Microswitches are used in many golf cart applications. They are use at the accelerator pedal to provide a signal to the solenoid that you have depressed the pedal and are ready to go. In an electric golf cart, the solenoid sends power to the controller to move the cart.

What is a golf solenoid?

In an electric golf cart, the solenoid sends power to the controller to move the cart. In a gas golf cart, the solenoid sends power to the starter/generator to start spinning the engine. Microswitches also serve a purpose as part of the forward and reverse direction selector switch on many golf carts. In this application, they can be used ...

Nivel

Plunger Style Micro Switch for 1963 to 1992 gas and electric Harley Davidson / Columbia Par Car Golf Carts. (Verify Fitment Below)

Product Overview

Plunger Style Micro Switch for 1963 to 1992 gas and electric Harley Davidson / Columbia Par Car Golf Carts. (Verify Fitment Below)

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9