How does a club cart throttle work?
As the foot pedal is pressed, the impulse is read by the electric motor and works accordingly. Four types of MCOR are fitted with different models of club cart manufactured in different years. This type of throttle device was used on all Carryall and DS models cars from the year 2000 and continued till 2012.
How do you adjust the throttle cable on a DS Golf cart?
Club Car DS throttle cable adjustment 1 After setting the golf cart to neutral and maintenance mode, jack up the rear. 2 Pull the spring that is present around the plastic piece located behind the shifter. ... 3 Loosen the throttle cable present in the cable box to adjust the extent to which you can take it out of the housing. More items...
How do you fix a clogged throttle on a golf cart?
Compress the spring between the cable stop and the throttle lever to close the throttle until the pedal is away from the microswitch so that the cart can run at less speed with very less throttle. You must do the compression until your problem goes off.
How to test a club CART motor controller output regulator?
The method of testing the motor controller output regulator or the MOCR is quite simple. While testing the club cart Precedent, it is done after searching the line item or the throttle. While the cart is in a “neutral” position, pressing the pedal will gradually move the throttle from 0% to 100% and be steady.
How do you adjust the throttle on a Club Car golf cart?
Loosen the throttle cable present in the cable box to adjust the extent to which you can take it out of the housing. Press the accelerator so that the golf cart starts up and begins to idle. Check the cable tension to make sure that it's still loose. The idle screw can be used to adjust the idling if it's very fast.
Where is the speed sensor on my Club Car golf cart?
The speed sensor in a Club Car Precedent golf cart is located on the back of the motor. To remove the sensor, unplug the cables behind the motor. You can use a 5/16-inch socket to remove the pigtail connector and pop off the plastic housing that encases the speed sensor.
How do you test a throttle sensor on a golf cart?
Take a digital multimeter and set it to the volts reading. Place the positive probe of the meter on the white wire terminal of the ITS. Release the accelerator pedal slowly. The reading should be in the 0.45V to 0.53V range when the micro-switch gets activated.
Where is the governor located on a Club Car golf cart?
0:061:28Where Is a Golf Cart Governor Located? - YouTubeYouTubeStart of suggested clipEnd of suggested clipWell a golf cart's governor located is actually down in the motor. Compartment. Some of them theseMoreWell a golf cart's governor located is actually down in the motor. Compartment. Some of them these electric ones nowadays. Actually the governor isn't a true governor. It is a control speed.
Where is the speed sensor located?
0:571:38Vehicle Speed Sensor Location - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo if you ever want to know where the vehicle speed sensor is this is where it is way back behindMoreSo if you ever want to know where the vehicle speed sensor is this is where it is way back behind the engine all right so that's a little look at where the VSS is located.
How do I know if my speed controller is bad on my golf cart?
When your golf cart's speed controller isn't operating correctly, your cart will show it by running erratically or failing to drive at one constant speed. If your cart starts showing these symptoms, the first thing you should look at is your speed controller.
How do I reset my club car controller?
Easily Reset the Club Car Golf Cart OBCKey switch to off.Set forward/reverse to neutral.Put tow/run switch to tow.Disconnect the negative battery terminal from the battery pack.Put the tow/run switch to run.Put forward/reverse switch to reverse.Put key switch to on.More items...
What does a throttle sensor do on a golf cart?
The inductive throttle sensor is a part installed into your cart's electrical system and is designed to control your speed. It works along with the speed controller and other similar parts to ensure that you get enough power for your cart whenever you run it.
How does the throttle work in an electric golf cart?
Just like the gas-powered car throttle, the throttle is an inductive sensor. It pushes the acceleration lever to send electricity to the solenoid and speed controller and drives the motor. Electric Motor. The electric motor requires the right amount of electricity to turn the cart's wheel.
How do you bypass the governor on a Club Car golf cart?
0:000:46How to remove governor on a Club Car golf cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the farther you bend that normally the faster it goes and then that's it basically when you wantMoreSo the farther you bend that normally the faster it goes and then that's it basically when you want to return your heart you just bend that back down and go back to normal speed.
How fast can a golf cart go without a governor?
What is the Average Golf Cart Speed? The average top speed of a typical golf cart without any upgrades is between 12 and 14 miles per hour. Without any sort of modification or upgrade on a golf cart, the top speed that you will be getting on a golf cart is about 14mph.
How do you make a Club Car golf cart go faster?
6 Ways You Can Make a Golf Cart FasterAdd More Torque to Your Golf Cart.Upgrade Your Golf Cart's Motor.Improve the High-Speed Controller of the Cart.Add Better Golf Cart Tires.Use a Higher Powered Golf Cart Battery.Watch the Weight in Your Golf Cart.
How do you bypass a speed sensor on a golf cart?
The speed sensor on the EZGO golf cart can be bypassed by unplugging it from the speed controller. By disconnecting the J5 pin on the speed controller, this will cause the golf cart to creep along as the controller will go into limp mode.
How do you remove the speed limiter on a Club Car golf cart?
0:040:46How to remove governor on a Club Car golf cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou open up this box lap. Here. It looks up look inside. There's 12 cable down right here this leverMoreYou open up this box lap. Here. It looks up look inside. There's 12 cable down right here this lever you want to lift up and Bend and that pulls on the cable a little more.
What controls the speed on a golf cart?
Essentially, your golf cart's speed controller sends its current and battery voltage to its motor. This process depends on your golf cart's input device, which includes its throttle. That's how your golf cart's speed controller lets you operate its acceleration rate, as well as its deceleration rate.
How does a speed sensor work on a golf cart?
Magnetic Style Many golf cart motor speed sensors employ an electromagnetic power to “read” the motor rpm. Generally, there is a magnet present in the closed end of the motor as well as the sensor itself which reads how the magnet is reacting with the magnetic field inside the motor.
What does it mean when a club cart is bad?
The club cart bad MCOR symptoms are commonly diagnosed as a erratic throttle jump. While pressing the pedal, if the club cart’s throttle moves smoothly from 0% to 100%, then the MCOR is ok.
How does a club car MCOR work?
The club car MCOR or the motor controller output regulator works like a dimmer in the headlight. It determines how much power is needed to get the desired speed by modulating the voltage.
What is the difference between MCOR and Club Car Precedent?
There is not much difference between installing MCOR on Club car DS and Club car Precedent. Club cart DS has MCOR1 or Carryall type controller, and the mounting is a bit different. However, this model of MCOR is not available anymore or sparingly available. Other types of MCOR are used while charging, and it needs to change ...
What does it mean when the MCOR on a golf cart is not working?
If the on/off positions are not working, then the MCOR on the club cart Precedent golf cart is not working or malfunctioning and needs repairing or replacement.
What is a MCOR in a club car?
What is an MCOR in a club car? The throttle device of any club cart is known as MCOR or motor controller output regulator. As the foot pedal is pressed, the impulse is read by the electric motor and works accordingly.
How to tell if a golf cart is bad?
Club Car golf cart bad MCOR symptoms 1 However, if there are erratic movements, say like 20%, then 60%, and then 15%, and likewise despite keeping the pedal pressed with uniform pressure, the MCOR is giving trouble. It will never reach 100%. 2 If it takes too much time for the MCOR reading to move up, the MCOR is malfunctioning. 3 The cart will not get enough speed as the motor will not move as per requirement and movement hiccups of the cart indicate that the motor is not getting enough or erratic power signals. It is a sign of a bad motor controller output regulator or the MCOR.
What happens if you don't press the accelerator on a MCOR?
However, if the desired speed is not reached despite pressing the accelerator, the MCOR causes problems. One needs to change or repair the MCOR if no other trouble is detected for the cart’s power loss. The MCOR may have corroded over time and require replacement.
How does a golf cart speed controller work?
The golf cart's speed controller sends its current and battery voltage to its motor. This entire process depends on your golf cart's input device, which includes its throttle. That's how the golf cart's speed controller allows you to operate its acceleration rate, as well as its deceleration rate.
Why replace club car speed controller?
There are several reasons why you might want to replace or repair your Club Car speed controller, including customization of Club Car, adjustment or upgrade of the motor, or upgrading Club Car controller to better fit your needs.
How many amps does a club car need?
If the cart is mainly used to transport 1 to 2 people or light loads on smooth roads, a small 2-5 horsepower and lower controller around 200-300 Amps will work best.
How to control a cart's speed?
In addition to controlling the cart’s speed, there are a few other functions that speed controllers can offer. Limit the current to the motor to protect both engine and controller in case of overloading. Determine the battery current so that battery is protected from excessive discharging. Monitor battery health and charge.
How to adjust low idle air on golf cart?
Position the golf cart to idle mode and set the low idle air adjustment according to your preference, for the engine to be able to pick up properly. This adjustment can be found on top of the carburetor. Often, two turns outward from the seated position is a good starting option.
Where is the main jet on a 4-cycle engine?
The main jet in the carburetor diagram of a 4-cycle engine is located below the carburetor while the pilot jet is present on top of it. The needle valve and float pin are also housed under the carburetor.
Why Do Carburetors Flood?
The reason why a carburetor floods on a golf cart is usually due to a faulty fuel pump.
What causes a carburetor to produce a lean mixture with insufficient fuel?
The engine starts overheating or backfiring that causes the carburetor to produce a lean mixture with insufficient fuel .
How to adjust valve clearance?
Do a valve clearance adjustment starting with the cold valve. The valves can be adjusted using a flat screwdriver, a feeler gauge and a 10mm wrench. The two inner exhaust valves and the outer intake valves must have a clearance of 0.004 mm.
Why change intake manifold?
Change the intake manifold so that the metering or fuel pump system gets powered.
What clearance do you need for an intake valve?
Do a valve clearance adjustment for both the outer intake valves and the inner exhaust valves. The inner exhaust valves and the outer intake valves must have a clearance of 0.004 mm.
