who can fix my club car ds golf cart

by Mr. Vincent Wehner MD Published 2 years ago Updated 2 years ago

How do you reset a DS Club Car?

Easily Reset the Club Car Golf Cart OBCKey switch to off.Set forward/reverse to neutral.Put tow/run switch to tow.Disconnect the negative battery terminal from the battery pack.Put the tow/run switch to run.Put forward/reverse switch to reverse.Put key switch to on.More items...

What does DS mean on a golf cart?

What does DS stand for in Club Car golf carts? The Club Car DS model type, in production from 1980 to 2014, was named after Dom Saporito, a vehicle designer at Club Car in the 1980s.

How much does a solenoid cost for a Club Car golf cart?

Golf Carts Universe Club Car DS Electric 36v Solenoid 100amp 8016Was:$29.74 DetailsPrice:$22.95You Save:$6.79 (23%)

How do I test my Club Car DS controller?

To test a club car precedent controller, connect a voltmeter between the negative terminal of your cart's battery and the M terminal on the controller. Then push the pedal down and look for a clicking noise from the solenoid. Your batteries should read as full.

Do they still make Club Car DS?

The Club Car DS was released back in 1984 and discontinued production in 2011. It was designed to be a Fleet Golf Cart for Golf Courses.

What is the difference between a Club Car and a Club Car DS?

One main difference between the two is that the Club Car Precedent has several technological features that are lacking in the DS. This is especially true for the Precedent i3 model of the Club Car Precedent golf cart. Unlike the Precedent, the Club Car DS is not equipped with an electronic scorecard.

How do you test a club car solenoid?

Set your multimeter to ohms and insert a probe on each large terminal with the key off and the cart direction switch in the neutral position. Press on the accelerator with the cart's movement control in the forward position, and the key is turned on. A click should be heard first from the solenoid.

How do you troubleshoot an electric club car?

2:3915:0248 Volt Club Car Diagnostics - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure your key switch is on step on the accelerator. You should get a light here.MoreMake sure your key switch is on step on the accelerator. You should get a light here.

How do you change a solenoid on a club car?

1:305:38Replace Solenoid in Golf Cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you start by removing the bolts that actually hold the solenoid to your golf cart wherever thatMoreSo you start by removing the bolts that actually hold the solenoid to your golf cart wherever that might be. And one of the tips i also like to mention is hold up your new solenoid.

Is there a reset button on a Club Car golf cart?

It should have a small reset button (Usually it will be red) located near the main battery supply. Hit the reset button and then put the cover back on the motor. The next step would be to recharge your cart and try turning it on again.

How do I know if my electric golf cart motor is bad?

You have enough going on in your life without your golf car refusing to start when you turn the key in the ignition. If your golf car won't start, is slower than it used to be, or is experiencing other technical problems, you could have a bad motor on your hands.

How do I know if my speed controller is bad on my golf cart?

Press the accelerator and watch to see if the voltage increases. It should increase from a reading of 0 to the full voltage of the battery. If the motor is not turning, the problem may be in the directional switch or motor. If there is no voltage, the controller is bad and must be replaced.

What tools do you need to dismantle a golf cart battery?

This battery consists of various cables and wires, which are crucial for the working of your vehicle. Cutters, crimpers, nails, and a screwdriver are all essential tools you should carry in case you want to dismantle or recharge your golf cart’s battery.

Why is it important to maintain a golf cart?

Hygiene and maintenance of your golf cart are not only important for your comfort but also the regular functioning of your golf cart. The clutch is the component of your golf cart used very frequently and can be easily soiled with dirt and dust particles.

Why does my electric golf cart jerk?

1] Water-logging in some of the components of your electric golf cart can result in jerking. Sensors and micro switches installed near the vehicle’s floor mat can malfunction due to water interference, which causes jerks when you accelerate.

How much does a DS golf cart weigh?

The DS produces both battery and gas-powered golf carts. The electric DS weighs 498 pounds, whereas the Gas DS weighs 619 pounds. The speed ranges between 12-15 miles/hour for the gas model, whereas 12-19 miles/hour for the electric one. Jerks can occur in the DS Car for the following reasons.

How fast is a club car?

Club Car’s gasoline-powered Tempo golf cart is one of the most highly coveted golf carts by golfers worldwide. Its speed ranges from12-15 miles/hour. The Tempo golf cart comes with a 5-year warranty and a dynamic engine of 3.3 horsepower.

How much does a club car precedent weigh?

It costs around 11,500 USD and has a minimum horsepower of 3.7 (2.7 kW). The Precedent weighs 1176 lbs, and its speed ranges from 8-14.8 miles/hour.

Why does my DS car jerk?

Battery damage: – Jerks can occur while accelerating in a DS model if the cart’s battery and other electrical components have been damaged . Repairing or replacing these components can lessen or nullify the problem of jerking.

Why does my club car DS flood?

The carburetor of a Club Car DS may flood due to the following reasons: Dirt accumulation: With extensive usage, the carburetor tends to become dirty. As a result, the float or needle gets stuck in the dirt. You’ll need to clean the carburetor well so that the float and needle get released and allow free flow of fuel.

Why does my golf cart flood?

A Club Car golf cart carburetor can flood due to a damaged fuel pump line, or because the needle isn’t sealed.

Why do you need to clean carburetor wells?

You’ll need to clean the carburetor well so that the float and needle get released and allow free flow of fuel. Crack in the float: The float may develop a crack or hole and get filled with gas. As a result, it will not float but will be pushed down. Changing the complete float setup is a good idea.

Why does my 2002 Club Car flood?

The most common reasons for flooding in a 2002 Club Car are improper float operation, faulty needle/seat, a soft intake hose, clogged plastic vent hose connected to the carburetor or a damaged air filter. Improper float operation: The float may malfunction because it’s damaged or dirty. In case of damage, do a replacement.

What to do if your fuel tank is not venting?

If so, a filter replacement is needed. The fuel tank is not venting and air suction takes place when you try to unscrew a hot cap . Replace the old fuel tank grommet and vent with a new set. Consider changing the fuel filter as well. The fuel pump or fuel lines are damaged because of the ethanol in the fuel.

Why is my fuel pump corroded?

As a result, the pump exerts too much pressure that overcomes the needle valve of the carburetor. When the fuel pump is replaced and good quality fuel is used, the flooding is arrested.

What to do if you don't get readings on golf cart?

If you are not getting these readings, change your batteries. You must keep in mind that there are differences between the various models of golf carts. Each model may have a different component and you have to be careful while handling them. Wrong handling can cause problems and the golf cart can get damaged.

Why won't my golf cart move?

A Club Car golf cart will not move if power from the battery pack is not reaching the motor. Faulty parts such as the solenoid, OBC and wiring can also cause a golf cart to not move.

How to know if a cart won't move?

When the cart won’t move, you have to be sure that the batteries are sending sufficient power to the circuit. You must check the fuse. Use the voltmeter to check the voltage at the key switch. In a cart with batteries rated at 48V, it must show 48V at the key switch.

How to check if a controller is corroded?

To check the controller, these are the steps: You will need a digital voltmeter (DVM) to check the 16-pin connector at the controller. Lift one wheel of the cart on a jack. The black probe from the DVM should be on the pack negative post.

How many batteries are in a golf cart?

Batteries: Some golf cart batteries are designed and structured in such a way that in a pack containing six batteries, #1, #2 and #3 will service the forward movement of the cart and #4, #5, #6 take over when the cart is reversed. So, if one of the batteries were to fail then the movement in that direction will be curtailed.

Where is the Delphi fuse holder on a 2010 Club Car?

For this, the first place you must check is the main fuse. In the 2010 Club Car Precedent, the Delphi fuse holder is located near the solenoid. There are standard operating procedures to be followed while working on your golf cart. The Run/Tow switch must be on Tow and preferably you should disconnect the batteries.

Is the Ping G25 adjustable?

Is the Ping G25 driver adjustable? The Ping G25 driver is adjustable. It’s possible to do four adjustments using the hosel adapter of the driver apart from the stated loft setting and...

How to troubleshoot a golf cart?

GOLF CART CONTROLLER TROUBLESHOOTING 1 Make sure it isn’t your batteries! If your batteries are old and dead, then your golf cart will not operate. Charge them fully first and attempt to drive the unit. 2 If your batteries are fully charged and your vehicle won’t run, when you press on the accelerator pedal, then you should hear a clicking sound which will indicate the solenoid is engaging and allowing power to flow to your controller. If there is no distinct clicking sound, then check your solenoid. Also, it could have to do with something in the accelerator device as well. But, we can eliminate the controller as being defective. 3 If your batteries are fully charged and you get a clicking sound ensuring the solenoid is allowing power to flow to the controller, then you can begin inspecting the controller 4 Check all the wiring and signs of disconnection or damage. Also, most controllers will have an operation light that will begin to flash a morse code that will unveil the secrets of the problem. If that is the case and all of the above have been eliminated, then you are getting closer to determining it is the controller.

Why won't my club car run?

Due to their expense, you want to be sure your controller is the major reason and problem with your Club Car. First off, if your controller is bad, your vehicle won’t run. However, there are other reasons that could lead to your vehicle not running. Here are a few quick troubleshooting tips.

What does it mean when there is no controller?

When there is no controller, it means batteries drainage is at its peak, as motors can operate independently at their high speed, which would gradually increase stress on the mechanical and electrical components and let motors and batteries degrade quicker.

Does a golf cart controller degrade?

As a controller in the Club Car or golf cart is made up of electrical and electronics components, it degrades gradually over time with the frequency of usage. But usage is not the only factor, controllers and the Club Car parts may also degrade in case of non-usage. For example, if a golf cart is left for no use for a longer period, ...

Can you trust aftermarket controllers?

price difference. Generally, Club Cars are made with highly precise and quality ensured engineering practices, so you can easily trust the aftermarket controllers if you don’t want to spend much.

Do golf carts have solenoids?

In the old days of golf carts, a series of solenoids were used which was not an efficient means for battery management. As today’s technology does not use full-on DC Motors, instead there exist Brushless DC Motors and AC Motors by way of which operators have the option to drive the Club Car at varying speeds.

Can you fry a controller?

Power may be disconnect ed, however it is not worth the additional risk to fry a controller. Lastly, when tightening the wires back onto the controller, do not use power tools. Use hand tools so that you don’t over tighten and potentially strip the connection.