The most common reason why your golf cart is stalling is due to a bad solenoid or a faulty speed controller. Batteries have lost charge Faulty ignition Problem with the direction switch Faulty speed controller Bad solenoid The solenoid wears out every time the gas pedal is pressed down. The solenoid gets pressed down to a thin plate.
Full Answer
Why does my golf cart turn off randomly?
Low battery voltage: Sometimes a dip in the minimum voltages of both batteries causes the Golf Cart to turn off randomly. It is best to use a voltmeter and check if the voltages of both batteries are reaching the bare minimum mark.
Why is my golf cart battery draining so fast?
You would have charged up your cart fully but after driving it around for an hour or two, the power would have got drained off completely. If this is a frequent occurrence with your cart, then you will need to take a look at the batteries. Also, you might notice that the batteries charge very quickly.
Why does my golf cart stall when I go up hills?
The first thing you need to check is the brake hub. It might be spinning out. The brake bub will spin out when there is too much load to prevent any damage to the rear axles, causing the golf cart to stall on hills. Remove the covers from the rear wheel.
What are the symptoms of an electric golf cart not starting?
On a gas golf cart, the most common symptom is the starter failing to engage – so the engine doesn’t turn over – while all you hear a series of very futile clicking sounds. On an electric golf cart, the most common symptom is the solenoid is not delivering electricity to the controller when the vehicle’s ignition is turned on.
Why does my golf cart go then stop?
In some cases, this happens because the coil of the battery is worn out or is too old. It can also be a sign of a faulty battery or even loose connections within the solenoid. Additionally, you could be dealing with overheated contacts. This is an issue you need to take seriously.
Why does my gas golf cart hesitation?
If your cart does not start smoothly, hesitates before starting, or does not gain speed properly, these are all signs of a bad or damaged accelerator.
Why does my golf cart chug?
A Club Car golf cart jerking from the front end of the golf cart occurs due to poor quality of tires. If the tires are worn out or loose, the golf car can start jerking. The uneven height of your front tires can also cause jerking.
How do you know if you have a bad solenoid on a golf cart?
If your golf cart fails to turn on when you turn the key on, this is the most obvious sign of solenoid failure. The solenoid clicks a little with the ignition system in regular operation; in most cases, a failing solenoid will not snap.
What is an MCOR on a golf cart?
Club Cars use an MCOR throttle device. This translates your foot movement at the pedal into electric impulse that the motor controller reads. MCOR stands for "Motor Controller Output Regulator".
Why do electric golf carts chug?
The most common reason for your golf cart jerking is often the battery terminal connections are loose and/or corroded. A poor connection prevents the correct amount of current from flowing through the set of batteries to your speed controller (or resistor coil), and ultimately to your electric motor.
Why is my golf cart sputtering?
Golf carts can spit and sputter for several reasons, but mainly due to worn out spark plugs or dirty filters inside the fuel system. There might be something wrong with the fuel system of your cart. You could be having a spit and sputter problem because the filter, pump and injectors in your golf cart are very dirty.
Should you charge a golf cart after every use?
Yes. New golf cart batteries should be charged every time they are used as this will extend their lifespan, help them retain their capacity for longer, and prevent discharge. It is vitally important to charge new golf cart batteries, even after their first use.
How do you diagnose a golf cart problem?
There are a few simple problems that you can fix yourself that will not necessitate professional maintenance.Test the wall socket where you charge your cart. ... Expose your golf cart batteries. ... Test the batteries for voltage. ... Replace dead batteries. ... Expose the motor for inspection. ... Reset the motor. ... Test the cart.
Will an electric golf cart run with a bad solenoid?
The ability of your golf cart to function properly depends largely on the solenoid. If the solenoid is broken and not working correctly, you may notice your golf cart won't start, picking up speed, or even working at all (issues with acceleration could also be caused by a bad speed controller).
Where is the reset button on a golf cart motor?
First, you'll want to reset your motor. It should have a small reset button (Usually it will be red) located near the main battery supply. Hit the reset button and then put the cover back on the motor. The next step would be to recharge your cart and try turning it on again. If it starts up then you're in luck!
How do you test a golf cart coil?
Attach the red lead to the positive terminal. Select the "Ohm" setting on your volt/ohm meter and read the display. The golf cart coil should register as more than 3.7 ohms, but less than 5.2 ohms. If the coil registers outside this range, replace the coil with a new unit.
Why does my golf cart spin out?
The brake bub will spin out when there is too much load to prevent any damage to the rear axles, causing the golf cart to stall on hills. Remove the covers from the rear wheel. Notice the castle nuts that are holding the hub to the axles. Apply the brakes.
Why does my golf cart stall?
The most common reason why your golf cart is stalling is due to a bad solenoid or a faulty speed controller. Batteries have lost charge. Faulty ignition. Problem with the direction switch. Faulty speed controller. Bad solenoid. The solenoid wears out every time the gas pedal is pressed down. The solenoid gets pressed down to a thin plate.
Why does my EZGO golf cart hesitate?
The main reason why an EZGO Gas golf cart hesitates while accelerating, is because of a dirty carburetor. A dirty carburetor causes this hesitation. Regular cleaning can prevent this problem. Check the rubber boot and clean if you spot any dirt. In case it has worn out too much, you can replace the carburetor.
How to check for leaks in golf cart?
You can check for any leaks by following these steps: Crank up the golf cart and check every seal for leakage. You can also spray wd40 at the clutch to find leaks. When the cart becomes hot, the voltage also drops. So, make sure you provide enough voltage to the batteries so the cart can run.
Why is my EZGO RXV hesitation?
In most cases, the hesitation problem occurs due to bad batteries. If you have bought new batteries for your EZGO RXV, make sure to fully charge them before the first use. Batteries should then be charged after every use. To keep the batteries in check, get a Digital MultiMeter to measure the individual voltage.
Why does my cart stutter?
If you change the battery, change the charger as well; otherwise, the battery will keep running down. If your cart seems to run fine for a few feet, and then it stutters, it is most likely the batteries. If it is not the battery, then check if it is the speed controller or the resistor.
What causes a cart to heat up?
Weak batteries. Bad connection between the batteries. If there are loose connections, it will cause heating in the battery. To check, you can drive your cart for a while and feel the temperature in the cables and connections. If there is no heating, then check the individual voltages.
Why does my golf cart keep turning off?
When a Golf Car is shutting off without warning, it’s because of low battery voltage, dead batteries, or because the solenoid coil is overheating. Low battery voltage: Sometimes a dip in the minimum voltages of both batteries causes the Golf Cart to turn off randomly. It is best to use a voltmeter and check if the voltages ...
Why does my golf cart cut out?
A golf cart may cut out at full throttle due to a faulty solenoid that needs replacing, or having too low of a battery voltage. Solenoid needs replacing: It may be that the solenoid of the Golf Cart may have developed some glitches due to which it is not responding at full throttle.
Why does my Yamaha G2 keep shutting off?
Yamaha G2 golf cart keeps shutting off: The Yamaha G2 Golf Cart may keep shutting off due to one of the following reasons: Loose solenoid wiring: The first check should be done whether the wiring on the golf cart is in right condition.
How to fix an EZGO golf cart?
The ways to fix a EZGO are stated below: Check the Solenoid contacts: The wires connecting the solenoid may not have electricity flowing due to which the Golf cart is getting abruptly shut off. It is recommended to change the wires connecting the solenoid and check if the problem gets sorted.
What happens if the voltage goes down on a golf cart?
Again, when the voltages go down, it will hit minimum and all the power that is gained shall be lost.
Why is my controller not connecting to the solenoid?
It is advisable to check the connections out there to check if the wires are getting disconnected.
Can you replace solenoid on golf cart?
Replacing the solenoid helps in most cases but it is advisable to get it checked at an authorized service center. Battery voltage is too low: In many instances, the batteries may not be carrying adequate amounts of voltage to keep the Golf Cart in running order. The voltages of the batteries should be checked via a voltmeter to see ...
Why does my EZGO golf cart stop?
Why your EZGO golf cart stops suddenly? The main reason why a EZGO golf cart stops suddenly is because of a bad solenoid or low voltage levels causing a thermal cut.
What is the red wire on a golf cart?
The red wire with the connector is the bypass. Ensure that the solenoid gets started at one go and all wirings connected to it are in perfect order. In case of any sort of loose wirings or broken wires, that may cause the golf cart to malfunction and it may come to sudden halts at frequent intervals.
Do you need a key switch on a golf cart?
The key switch or the solenoid should be in perfect order to ensure the golf cart is working perfectly. Ensure there are no loose wirings in the solenoid, if the wirings get damaged then it is recommended to change the wirings. The RXV has been known to be very sensitive to battery voltage.
Can you remove plastic wiring from an EZGO RXV?
The plastic wiring can be removed by getting those untapped from the wires and inspecting those.
Why does my golf cart jerk?
The most common reason why are golf cart jerks could be that the water has entered some of the components . There are a sensor and a micro-switch under the driver’s side floor mat. If water enters these components, especially the switch, it could cause the cart to jerk while starting.
What happens if your golf cart clutch is bad?
If the clutch is bad, you could experience some jerking movement during the start or stopping stage of the golf cart. Consider getting the clutch checked and possibly replaced if any issues are there. This should help resolve the problem of the cart jerking when accelerating or taking off.
Why is my cart bouncing?
If the cart is still bouncing, you will know that the problem is not with the tire. Instead, the issue could be due to a bent wheel. In this case, you will just have to get the wheel replaced. If both these cases do not seem to be the cause, then it could be due to the axle or the wheel bearing.
Why does my clutch jerk?
Well, the issue could be related to the clutch. The primary clutch weights could be broken, which might be causing the jerks. It would be a good idea to get your clutch checked to help resolve the problem. Another cause of this issue could be the accumulation of dirt or dust particles in the clutch.
Can you use an ohmmeter to calibrate a cart?
In such cases, you will have to use an ohmmeter to calibrate the readings and make the necessary adjustments. Any technical manual of your cart model will have details about the various parts. You can either use them to recalibrate it or take your cart to a service center. They can easily fix it for you.
Why is my golf cart not clicking?
On an electric golf cart, the most common symptom is the solenoid is not delivering electricity to the controller when the vehicle’s ignition is turned on. In normal operating conditions, the solenoid clicks on and off with the ignition switch. A failing solenoid will generally not click. Two things could be going on here.
What does it mean when a golf cart solenoid goes bad?
Technically, in fact, a solenoid is a shape – a shape in which the length of something coiled is longer than the diameter of the coils. In engine starters, this refers to the smaller motor ...
How to check if a golf cart solenoid is silent?
On an electric golf cart, if the solenoid is silent – no clicking – use the setting voltmeter to DC volts using the 200 range. First, turn on the ignition while looking for a reading on the smaller terminals. If nothing is appearing, then press on the accelerator. If the needle doesn’t move, then the problem is not with the solenoid.
Why do golf carts have solenoid?
The solenoid is simply there to allow electricity to flow freely to the controller and motor which will result in a running golf cart. RELATED: 4 Signs you need to Replace your Golf Cart Batteries.
Why won't my solenoid click?
The solenoid might not be getting enough electricity to do its work – which could be caused by loose connections, a weak battery or the coil wearing out.
What does a solenoid do when you turn the ignition?
Step by step, it looks like this: When you turn the ignition key, a small amount of electricity goes to the solenoid. The solenoid uses that small amount of juice to close two heavy-duty contacts that allows a large jolt of electricity to pass through the starter. The solenoid also sends a pinion gear forward, which is the device ...
Why does my golf cart backfire?
Golf Cart Backfires Because Fuel Mixture Is Too Rich. Always check the air and fuel ratio to make sure your engine is not receiving too rich of a fuel mixture. The following adjustments are an example of most carburetors, but you should look up the proper number of screw turns your model requires.
How to adjust a golf cart?
Adjustment is made by loosening the nut or screw, pressing the throttle closed, and then retightening the nut. Some golf carts may not have accelerator cables but instead will have a series of rods between the gas pedal and the carburetor.
What happens when the throttle cable is out of adjustment?
When the throttle cable is out of adjustment, the throttle plate never completely closes, allowing unburned gasoline to accumulate in the exhaust system before the spark plug fires. Here are a few tips for adjusting your golf cart engine to keep it from backfiring.
Why is my throttle plate not closing?
If none of these accelerator cable adjustments solve the problem, then the throttle plate may not be closing all the way due to an obstruction or internal mechanism being bent. Unfortunately, the only way to find out if this is true is to remove the carburetor and inspect it.
What is the ignition system on a golf cart?
Older golf carts used a set of points and a condenser to produce the spark needed to run the engine, but the more modern carts have a solid-state ignition system . The solid-state system utilizes an internal magnetic pickup device inside the engine that sends an electrical signal down the line to the igniter.
What is a golf cart?
Golf carts are also known as golf cars. The term "cart", in its purest sense, refers to a vehicle that does not travel under its own power. Golf cars, however, are most commonly referred to as golf... Continue Reading.
How long does it take for a muffler to burn off?
It sounds crazy, but the common method of un-coking a muffler is to remove it from the cart and barbecue it over a fire for about half an hour. This will burn off all of the debris inside the muffler and turn it to ash.
Why does my golf cart beep?
Golf carts are designed to carry a specific load for a distance. Replacing the tires may put them under a great deal of pressure for their torque. If all of these efforts fail, you can inspect the batteries or the motor. If any of these have malfunctioned, then you may hear the beeping sound.
Why does my golf cart make a grinding noise?
If your golf cart is making a grinding noise while running, the issue could be due to the bearings. The grinding noise is very irritating, and the problem is generally with one of the physical or mechanical parts.
Why does my washing cart make a buzzing noise?
If the buzzing noise is coming right after you washed your cart, it could be because of the water getting under the floorboards. The best solution is to let the water dry well before using the cart.
How long does it take for a bearing to go bad?
This is because, once bearings start to go bad, they often fail almost entirely and can become almost unusable in just a few hours.
Can you leave water in a F&R switch?
However, you may also have some water left in your F&R switch, or it could be because of water on the battery wires. This water-related danger is one you need to take very seriously.
Is it dangerous to drive a golf cart?
Golf carts sometimes make some weird noises, and most golf cart owners have experienced it. While these noises may not be dangerous, they can be irritating and a sign of damage.