Your Yamaha golf cart probably keeps running because of loose wires, a sticking accelerator stop switch or a sticking solenoid. It could also be a problem with the engine stop relay or a problem with the voltage regulator. Your Yamaha golf cart keeps running because of loose wires.
Why does my Yamaha G1 golf cart keep running?
Why does your Yamaha G1 golf cart keep running? Your Yamaha G1 golf cart might not be able to stop and shut off properly because of loose wires, a sticky solenoid or a sticky accelerator stop switch. Look at the TCI wire connector at the front of the engine.
How to fix my Yamaha golf cart that won’t turn off?
Also check the connection of the black and blue wires at the front of your cart’s engine. If you find that the wires are just disconnected, you only need to reconnect them to get your golf cart to shut off properly. Your Yamaha golf cart has a sticking accelerator switch.
Why does my golf cart keep shutting off?
There may be various reasons of the Club Car Precedent to keep shutting off, let us discuss on few of the common ones: Check voltage of the batteries: Use a voltmeter to check if both batteries are showing the minimum voltage requirements to keep the golf cart in running condition.
Why is my Yamaha golf cart sticking accelerator switch?
Your Yamaha golf cart has a sticking accelerator switch. If your cart has problems stopping, you might have a sticking accelerator switch on your hands. This will make you need to push the gas pedal multiple times to get it to work properly.
Why won't my golf cart shut off?
Troubleshooting. Switch the car to neutral before turning the key off. The problem with shut down may have occurred from the kill circuit, which is controlled by the top microswitch. You may have to replace the microswitches or solve the problem by tightening up the circuit.
How do I reset my Yamaha golf cart?
Identify your main battery supply (usually the largest battery) on your motor. Check around this supply for a small red button that may or may not be labeled “Reset”. Press and hold this button for a few moments and then release it to reset the motor.
How do I make my Yamaha golf cart idle?
0:523:44How to get your club car to idle - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe black wires gonna be on the bottom half down here you can't see it but just disconnect it onceMoreThe black wires gonna be on the bottom half down here you can't see it but just disconnect it once you disconnect that you're gonna have to get your flat-head screwdriver and turn up the idle.
What does a stop switch do on a golf cart?
When the pedal is depressed, the switch is activated and sends a signal to the solenoid, allowing your golf cart to start. When it is released, the circuit is open and the car stopped. If your car won't start and you don't hear the solenoid click, the problem could be either this switch or the key switch.
Is there a reset button on a Yamaha golf cart?
Expose the motor (you'll probably need a screwdriver to remove the cover), and look for a red button. It is usually near the main power source, where most of the wires are connected. Once you've pressed the button to reset the motor, reassemble the cart, charge up the batteries, and give it a test run.
How do I know if my golf cart controller is bad?
X Common Symptoms of Controller FailureTop Speeds Not Appropriate for Your Cart. Golf carts are designed to reach pretty specific speeds and to not go over them or beneath them. ... Sudden and Unexpected Slowing. ... Shuttering or Shaky Driving. ... Stalling Out and Refusing to Start. ... Surges in Speed When Driving.
Why does my golf cart keep running?
Yamaha golf carts can keep running and not stop for many reasons. It's usually loose wiring, a sticking accelerator stop switch, a sticking solenoid or issues with the engine stop relay or the voltage regulator.
How do you adjust the governor on a Yamaha golf cart?
0:005:15Yamaha G29 Drive Golf Cart Governor Adjustment - MORE SPEED!!YouTubeStart of suggested clipEnd of suggested clipItself by tightening this nut down you're putting more pressure on the spring. So that the governorMoreItself by tightening this nut down you're putting more pressure on the spring. So that the governor has to work harder to pull back on the throttle.
How do you take the governor off a Yamaha golf cart?
General InstructionsDetach the cable from the carburetor. The cable is about the width of a straw. ... Follow the disconnected cable up to the governor. ... Disconnect the gas pedal cable from the governor and reroute it to the carburetor. ... Using your wrench, remove the bolt on the gas pedal shaft.
What does a Yamaha stop switch do?
The Yamaha Stop Switch for select G models is what every other manufacturer calls an accelerator pedal microswitch. Yamaha, for some reason, had to have a different name and an over-engineered product to do the same job. This is a plunger-style switch that helps route the activation voltage through to the solenoid.
Where is the micro switch on a Yamaha golf cart?
In a golf cart, you're going to find a large number of these switches throughout its build. For example, there is a micro switch located on the accelerator pedal. This switch activates when you push the pedal and sends a signal to the solenoid.
Where is the solenoid located on a Yamaha golf cart?
0:095:38Replace Solenoid in Golf Cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipCart um your solenoid could be located in a bunch of different places but almost always underneathMoreCart um your solenoid could be located in a bunch of different places but almost always underneath the seat.
Where is the reset button on golf cart motor?
First, you'll want to reset your motor. It should have a small reset button (Usually it will be red) located near the main battery supply. Hit the reset button and then put the cover back on the motor. The next step would be to recharge your cart and try turning it on again. If it starts up then you're in luck!
Where are the fuses on a Yamaha golf cart?
Yamaha Golf Cart Fuse Box Location The fuse box in a 2014 Yamaha golf cart is located on the left side of the controller. The wires are tied to the roof drain. In a G2 electric cart, the fuses are present on the rear inner fender. This is on the front of the driver's side of the cart.
How do you reset golf cart batteries?
Step 1: Tip the battery on its edge: Allow approximately half the battery acid to run out of each cell and into a plastic container. ... Step 2: Mix 8 ounces of Epsom salts into 2 quarts of warm distilled water: Stir thoroughly. ... Step 3: Put the battery or batteries on a charger.
Why does my electric golf cart not move?
When the cart won't move, you have to be sure that the batteries are sending sufficient power to the circuit. You must check the fuse. Use the voltmeter to check the voltage at the key switch. In a cart with batteries rated at 48V, it must show 48V at the key switch.
What is a gas club car?
Gas club cars are mostly used for maneuvering rolling hills, rougher terrain, and for transportation of heavy payloads. Here I have mentioned a few troubleshooting steps which can help to shut off your car, and also, they are necessary when you are using the vehicle regularly.
How to turn off a car with a key?
Switch off the car with your key. Set forward or reverse to neutral. Now find out the run or tow switch and put it to tow. If the negative battery terminal is connected to the battery pack, disconnect it. Now put the switch from tow to run and the forward or reverse switch to reverse. Then turn the key switch on.
Can you fix a 2003 club car golf cart?
There are a few things you need to do to fix the shutdown issue of the 2003 club car golf cart. If your car is new and still facing such problems, then do not worry. It’s just a matter of minutes, as there will be no bigger issues. They can be fixed easily.
Can you fix a faulty solenoid?
You cannot fix the solenoid; in case of the faulty solenoids, replacement is the only option.
Why is my Yamaha golf cart not moving?
The main cause of a Yamaha golf cart clicking but not moving, is a faulty controller or solenoid. The battery has to be checked first to see if it’s delivering the right voltage while in the idle state as well as when the pedal is pressed. There can be other reasons for the Yamaha golf cart not moving though you hear the click.
What to do if your G9 golf cart is not clicking?
If you find your G9 Yamaha golf cart not starting nor clicking, check the key components for damage. If you find the parts to in good condition, check the brushes in the starter/generator.
Why is my solenoid not clicking?
The reason why the solenoid is not clicking could be that it is faulty or has no grounding. Experts recommend checking all wiring and cable connections to rule out this possibility. Batteries on your G16 Yamaha golf carts should raise sufficient power to reach the solenoid and the starter/generator.
What is a faulty controller?
The controller is one major component that may have to be replaced. A faulty controller can stall the cart and the click you hear must be from the solenoid. Test the solenoid to see if it is functioning properly. You will require a multimeter, preferably a digital one, or a DVM for this.
How to check solenoid on G9 Yamaha?
The solenoid can be checked using an old screwdriver to jump the terminals. Your G9 Yamaha golf cart’s key must be in the start position. If the starter turns when you do this, your solenoid needs to be replaced. You must be careful while doing this crude test; there could be sparks when the two terminals touch.
Why does my golf cart keep powering off?
If the cart starts powering off after a new installation, then you will know that the issue is caused due to errors with the installation.
Why does my golf cart cut out?
Another reason why golf carts can cut out is due to problems with the battery voltage or water levels.
How to check battery water level in golf cart?
How to Check Battery Water Levels in a Golf Cart. Check if the voltages in both the batteries are at the designated levels. Also, if the water in the batteries has dried up, it could cause this issue. Check for the electrolyte and water levels in the batteries. Make sure that you are not overcharging or undercharging your batteries as these could ...
Why does my cart have a loose solenoid?
If the connections from the solenoid have become loose or if there is some other loose contact, the cart might behave in this manner. It can also be caused by a faulty motor or a faulty key switch.
What happens if you charge your golf cart?
You would have charged up your cart fully but after driving it around for an hour or two, the power would have got drained off completely. If this is a frequent occurrence with your cart, then you will need to take a look at the batteries.
Can you fix a golf cart on your own?
Under NO circumstances should you attempt to fix your golf cart on your own. Doing so is dangerous and could result in serious bodily harm. The information on this website has not been verified for accuracy and should only be used for general information purposes only. Use this information at your own risk.
Is my speed sensor broken?
There is a magnet associated with the speed sensor. Sometimes your speed magnet may be broken but will still be clinging on; only being held by the screw. Unfortunately, you may not realize it is broken until you take the mechanism apart. The speed sensor may not even show any issues. Check if the magnet is broken and if it is, ...
Why does my golf cart stop running?
Your golf cart may stop frequently while running in case of a faulty spark plug, defective TCI/carburetor, or improperly seated internal baffles and airbox lid . Sometimes, an empty or close-to-empty fuel filler, low battery charge, a binding linkage, or a bad fuel pump can cause a golf cart to stop running. Faulty spark plug.
Why won't my Yamaha G2 golf cart run?
A Yamaha G2 golf cart may stop running if the air box is warped, if it isn’t sealing properly, if the carburetor is dirty, or if the crankcase seals are damaged. Check for improper sealing or warping of the airbox.
Why won't my golf cart run without a choke?
The golf cart may not run without choke because of a lean issue, cracked or broken crankcase seals, a clogged filter or main jet in the carburetor, a defective carburetor gasket, or unaligned timing gears and belt.
Why won't my 1996 EZGO run?
A 1996 EZGO won’t stay running if the muffler is plugged, reeds are flipped, the filter is clogged, or in case of too much or too little fuel in the fuel filter. Look out for a plugged muffler and clear it by following the steps given above in the section ’EZGO Marathon golf cart won’t stay running’.
Why won't my 1988 EZGO stay running?
A 1988 EZGO won’t stay running if the hooking of throttle cable or governor adjustment is not proper, the carburetor shaft is worn-out, or if the crank seals or a muffler is damaged. Check if the throttle cable is accidentally hooked up backward and if so, hook it in the proper direction.
Why does my 1994 EZGO stop?
A 1994 EZGO may stop frequently while running due to a dirty carburetor, a bad fuel pump, incorrect valve adjustment, loose timing pulleys, or shot intake valves. Clean the carburetor and all its parts thoroughly using a thin wire and carburetor cleaner.
How to check if muffler is blocked?
To check if the muffler is blocked, loosen the bolts present between the pipe and the muffler so that there is a gap of about an inch. If the cart runs, then it is an indication of a blocked muffler. Ensure that the oil injector is hooked up properly and that there isn’t too much oil in the mixing ratio.
Why does my golf cart keep turning off?
When a Golf Car is shutting off without warning, it’s because of low battery voltage, dead batteries, or because the solenoid coil is overheating. Low battery voltage: Sometimes a dip in the minimum voltages of both batteries causes the Golf Cart to turn off randomly. It is best to use a voltmeter and check if the voltages ...
Why does my golf cart cut out?
A golf cart may cut out at full throttle due to a faulty solenoid that needs replacing, or having too low of a battery voltage. Solenoid needs replacing: It may be that the solenoid of the Golf Cart may have developed some glitches due to which it is not responding at full throttle.
Why does my Yamaha G2 keep shutting off?
Yamaha G2 golf cart keeps shutting off: The Yamaha G2 Golf Cart may keep shutting off due to one of the following reasons: Loose solenoid wiring: The first check should be done whether the wiring on the golf cart is in right condition.
How to fix an EZGO golf cart?
The ways to fix a EZGO are stated below: Check the Solenoid contacts: The wires connecting the solenoid may not have electricity flowing due to which the Golf cart is getting abruptly shut off. It is recommended to change the wires connecting the solenoid and check if the problem gets sorted.
What happens if the voltage goes down on a golf cart?
Again, when the voltages go down, it will hit minimum and all the power that is gained shall be lost.
Why is my controller not connecting to the solenoid?
It is advisable to check the connections out there to check if the wires are getting disconnected.
Can you replace solenoid on golf cart?
Replacing the solenoid helps in most cases but it is advisable to get it checked at an authorized service center. Battery voltage is too low: In many instances, the batteries may not be carrying adequate amounts of voltage to keep the Golf Cart in running order. The voltages of the batteries should be checked via a voltmeter to see ...
Why does my EZGO golf cart stop?
Why your EZGO golf cart stops suddenly? The main reason why a EZGO golf cart stops suddenly is because of a bad solenoid or low voltage levels causing a thermal cut.
What is the red wire on a golf cart?
The red wire with the connector is the bypass. Ensure that the solenoid gets started at one go and all wirings connected to it are in perfect order. In case of any sort of loose wirings or broken wires, that may cause the golf cart to malfunction and it may come to sudden halts at frequent intervals.
Do you need a key switch on a golf cart?
The key switch or the solenoid should be in perfect order to ensure the golf cart is working perfectly. Ensure there are no loose wirings in the solenoid, if the wirings get damaged then it is recommended to change the wirings. The RXV has been known to be very sensitive to battery voltage.
Can you remove plastic wiring from an EZGO RXV?
The plastic wiring can be removed by getting those untapped from the wires and inspecting those.