
Faulty parts such as the solenoid, OBC and wiring can also cause a golf cart to not move. You must check your battery pack thoroughly. A 36V battery must show 38.3V on a full charge, while e a 48V battery reading must be 50.3V.
Why is my electric golf cart not working?
When there is a disruption in the flow of the electrical current, your cart will not operate. A common reason for current disruption is solenoid wear. Each time the solenoid activates as you press down on the gas pedal, the solenoid compounds down onto a thin metal contact plate.
What to do if your golf cart won’t move?
When the cart won’t move, you have to be sure that the batteries are sending sufficient power to the circuit. You must check the fuse. Use the voltmeter to check the voltage at the key switch. In a cart with batteries rated at 48V, it must show 48V at the key switch.
Why won't my golf cart go forward or reverse?
If the contact studs on the cam in the forward and reverse switch aren't aligned properly the solenoid will click but the golf cart won't move. I've seen quite a few new forward and reverse switches with the contacts installed wrong. Here's a link with more pictures of a EZGO forward and reverse switch and proper alignment of the contact studs.

What would cause an electric golf cart not to move?
Solenoid Wear When there is a disruption in the flow of the electrical current, your cart will not operate. A common reason for current disruption is solenoid wear. Each time the solenoid activates as you press down on the gas pedal, the solenoid compounds down onto a thin metal contact plate.
Why does my golf cart click but not move?
A Club Car golf cart can start clicking but not move, due to dust accumulating inside the battery ports. Opening the battery ports and checking whether there is any dust accumulation can tell you if this is the case. Cleaning it thoroughly with a cloth can resolve the problem.
Why won't my EZGO golf cart go forward or reverse?
For example, if your run/tow switch has malfunctioned, your cart won't go forward or backward. This switch is designed to change your cart's operating mode from normal operation to increased power for towing. Check the switch to make sure that it isn't “stuck” between the two modes.
How do you reset an electric golf cart?
First, you'll want to reset your motor. It should have a small reset button (Usually it will be red) located near the main battery supply. Hit the reset button and then put the cover back on the motor. The next step would be to recharge your cart and try turning it on again. If it starts up then you're in luck!
How do you fix a golf cart that won't move?
When the cart won't move, you have to be sure that the batteries are sending sufficient power to the circuit. You must check the fuse. Use the voltmeter to check the voltage at the key switch. In a cart with batteries rated at 48V, it must show 48V at the key switch.
What do you do if your golf cart won't go?
Press the button and put your cart back together before hooking it up to charge. In many cases, this will solve the problem. If it doesn't, try removing the motor and testing it with a separate, fully charged battery. If nothing happens, the motor is probably burned out.
How do you troubleshoot an electric EZGO golf cart?
Things to Keep in Mind Before TroubleshootingEZGO golf cart batteries aren't perfect right away.Sticky accelerators are perfectly normal and can be fixed easily.Keep your cart stable.Make sure your charging wall socket isn't faulty.Keep your tire pressure stable.Troubleshooting the speed controller.
How do you make a golf cart go forward?
0:5911:38Golf Cart Forward Reverse Switch - YouTubeYouTubeStart of suggested clipEnd of suggested clipMost likely that your forward reverse switch. Which is located right there. This is what makes yourMoreMost likely that your forward reverse switch. Which is located right there. This is what makes your golf cart go forward or reverse.
How do you test a golf cart controller?
How to Test a Club Car Golf Cart Speed Controller? The simplest test to ascertain your golf cart controller's performance is to to watch whether it runs when the batteries are fully charged with a slight push of the pedal. If you hear a distinct clicking noise, then your golf cart is running correctly.
Where is the reset button on an electric Club Car golf cart?
It should have a small reset button (Usually it will be red) located near the main battery supply. Hit the reset button and then put the cover back on the motor. The next step would be to recharge your cart and try turning it on again.
Do all electric golf carts have a reset button?
Electric golf cart motors have a reset button on their chassis which is designed to put your motor back into its original factory state. While it doesn't repair damage that may have occurred to the motor over the years, obviously, it does help to overturn any changes to the operation which may have occurred.
How do you know if your golf cart motor is bad?
You have enough going on in your life without your golf car refusing to start when you turn the key in the ignition. If your golf car won't start, is slower than it used to be, or is experiencing other technical problems, you could have a bad motor on your hands.
Why won't my golf cart move?
A Club Car golf cart will not move if power from the battery pack is not reaching the motor. Faulty parts such as the solenoid, OBC and wiring can also cause a golf cart to not move.
How to know if a cart won't move?
When the cart won’t move, you have to be sure that the batteries are sending sufficient power to the circuit. You must check the fuse. Use the voltmeter to check the voltage at the key switch. In a cart with batteries rated at 48V, it must show 48V at the key switch.
How to check if a controller is corroded?
To check the controller, these are the steps: You will need a digital voltmeter (DVM) to check the 16-pin connector at the controller. Lift one wheel of the cart on a jack. The black probe from the DVM should be on the pack negative post.
How many batteries are in a golf cart?
Batteries: Some golf cart batteries are designed and structured in such a way that in a pack containing six batteries, #1, #2 and #3 will service the forward movement of the cart and #4, #5, #6 take over when the cart is reversed. So, if one of the batteries were to fail then the movement in that direction will be curtailed.
What happens if one of the batteries fails?
So, if one of the batteries were to fail then the movement in that direction will be curtailed. Checking individual batteries is very important to avoid such a situation. Controller: The design and functioning of the controller are similarly divided into forward and reverse movements of the golf cart.
What to do if you don't get readings on golf cart?
If you are not getting these readings, change your batteries. You must keep in mind that there are differences between the various models of golf carts. Each model may have a different component and you have to be careful while handling them. Wrong handling can cause problems and the golf cart can get damaged.
Where is the Delphi fuse holder on a 2010 Club Car?
For this, the first place you must check is the main fuse. In the 2010 Club Car Precedent, the Delphi fuse holder is located near the solenoid. There are standard operating procedures to be followed while working on your golf cart. The Run/Tow switch must be on Tow and preferably you should disconnect the batteries.
Why won't my golf cart move?
Loose or corroded cable connections or a faulty controller can also cause the golf cart to not move. Malfunctioning microswitch. Faulty solenoid. Defective ignition switch. Loose or corroded cable connections. Faulty controller.
What happens if your golf cart battery doesn't charge?
Look out for a closed pedal switch that could be restricting the movement of the golf cart. When this is released, the cart will start moving properly .
Why won't my EZGO go forward?
The main reason why a EZGO gas golf cart will not go forward is because of a locked up brake, or a faulty solenoid and accelerator. A defective Run/Tow or Forward/Reverse switch can also cause a EZGO to not move forward. You can check out the steps given below to address this problem. Check if the brakes are performing as desired ...
What happens if a golf cart solenoid is defective?
When defective, the solenoid fails to transfer current from the battery to other parts of your golf cart.
How to check if ignition switch is working?
You can do this by hooking the wires present under the dash, connecting it to the battery, an ohmmeter, and check the reading. If you don’t get any reading, change the switch.
Is the Ping G25 adjustable?
Is the Ping G25 driver adjustable? The Ping G25 driver is adjustable. It’s possible to do four adjustments using the hosel adapter of the driver apart from the stated loft setting and...
Why won't my EZGO golf cart start?
EZGO golf carts may not start due to a transmission problem, corroded battery terminals or a faulty wiring coming from the ignition. Transmission Problem For safety reasons, many EZGO golf carts won’t start if its transmission is not in the Park position. Check and make sure the gear is in the Park position.
Why is my golf cart ignitor failing?
The most common reason for a failed ignitor is a bad voltage regulator. Therefore, when you replace or fix the ignitor on your golf cart, make sure you also check the voltage regulator and see if it needs to be replaced. There have also been cases where the battery has switch polarity for some reason.
Why won't my EZGO RXV move?
Brake Problems: Many times the reason your RXV won’t move is because of brake problems. The RXV is designed to be disabled when there is a problem with the break. Many times, the wiring that connects the brakes to the controller gets loose or is damaged. This can disable your EZGO RXV.
Why does my golf cart make a clicking noise?
When you press your golf cart pedal you should hear a clicking noise, if you don’t hear a clicking noise there might be a problem with the solenoid. To make sure your solenoid is functioning properly check it with a voltmeter. If you hear a click then you need to check its power with the voltmeter.
How to check if golf cart battery is corroded?
Also, make sure the golf cart is turned off. Start checking the battery by twisting the battery connector back and forth and then try and start the golf cart. If the golf cart almost starts or starts successfully then it’s highly likely that the battery terminals are corroded.
What to do if replacing ignition wire doesn't work?
To check the continuity of the ignition wire you’ll need to use an ohmmeter or a continuity tester. To do this, set the switch to off and set your ohmmeter to X1.
Why is my golf cart not accelerating?
When your electric golf cart does not accelerate, the first thing you need to keep in mind is that it is not a regular vehicle like your car . That's why the methods and solutions you use to get your car to start are not the same as the solutions you can apply to your cart.
What happens if your golf cart doesn't accelerate?
Bad Solenoid. If your golf cart does not accelerate, there is a possibility of the damaged solenoid. The solenoid is basically an electrical switch that enables the battery's flow from the battery into the motor. Check out the signs of the bad solenoid.
Why is my golf cart speed controller not working?
There are many reasons behind a speed controller malfunction. The most common problem that happens in the controller has aged due to infrequent use. These are just some of the issues that could be affecting your vehicle's acceleration. If you have trouble finding the issue of your golf cart accelerator, don't be afraid to take it to the mechanic.
How does a golf cart solenoid work?
The golf cart speed controller and solenoid are both controlled by the accelerator. The pedal is connected to the potentiometer. That means when you are pressing the pedal for acceleration, you are actually going through the potentiometer by pushing a rod. The potentiometer works as a communicator and tells the speed controller how much voltage it ...
Why is my golf cart not moving?
The golf cart will not be able to move at a steady or constant speed and that is one of the first warning signs of a problem with the speed controller of the vehicle. Here are a few things you can do to fix the issues associated with your speed controller.
Why won't my golf cart work?
The golf cart will not function if the transfer of electric current is disrupted. Current gets disrupted when the solenoid gets worn out or damaged. When you press the pedal, the solenoid gets activated and compounded into a metallic contact plate.
What happens if oxygen sensor is damaged on Yamaha G29?
Therefore, if the oxygen sensor is damaged, the engine of the Yamaha G29 golf cart will be oblivious to any information about the air-fuel mixture. This will, invariably, cause acceleration problems.
How does a speed controller work on a golf cart?
Once you do this, the brake should release and the cart will start accelerating once again. The speed controller works towards regulating the speed of the golf cart. There are instances when the speed controller fails but the vehicle will still start and move ahead.
Why is my golf cart solenoid not working?
If you encounter a problem with the solenoid of your golf cart, then you must know that it could be because of a faulty speed controller. To check the condition of your vehicle’s solenoid, you will be required to take a reading of the voltage and check if it is the same as the reading from the battery.
What is the function of a golf cart solenoid?
Its main function is to enable the flow of electricity from the battery into the motor. When you press the gas pedal and hear a sound that resembles a tap, you must know that the solenoid has been activated. The golf cart will not function if the transfer of electric current is disrupted.
What happens when a golf cart is not working?
When the speed controller malfunctions or does not work properly, the cart will move but with several breaks in between. The golf cart will not be able to move at a steady or constant speed and that is one of the first warning signs ...
Why is my Yamaha golf cart not moving?
The main cause of a Yamaha golf cart clicking but not moving, is a faulty controller or solenoid. The battery has to be checked first to see if it’s delivering the right voltage while in the idle state as well as when the pedal is pressed. There can be other reasons for the Yamaha golf cart not moving though you hear the click.
What to do if your G9 golf cart is not clicking?
If you find your G9 Yamaha golf cart not starting nor clicking, check the key components for damage. If you find the parts to in good condition, check the brushes in the starter/generator.
Why is my solenoid not clicking?
The reason why the solenoid is not clicking could be that it is faulty or has no grounding. Experts recommend checking all wiring and cable connections to rule out this possibility. Batteries on your G16 Yamaha golf carts should raise sufficient power to reach the solenoid and the starter/generator.
What is a faulty controller?
The controller is one major component that may have to be replaced. A faulty controller can stall the cart and the click you hear must be from the solenoid. Test the solenoid to see if it is functioning properly. You will require a multimeter, preferably a digital one, or a DVM for this.
Why do you need a wiring diagram?
A clear wiring diagram will help in ensuring that the cables are properly reconnected if you remove them for testing. In the solenoid, for example, the contacts inside can get jammed over a period. These have to be checked, cleaned, and re-fixed. If it still doesn’t work it has to be replaced.