In gas golf carts, a micro switch located on the accelerator pedal triggers a signal that will start the cart’s engine. The cart will run without any problem as long as this micro switch remains active. Moves the golf cart in forward and reverse
How does a micro switch work on an electric golf cart?
A micro switch on the accelerator pedal gets activated once the pedal is pushed. This sends a signal to the solenoid and in turn more power to your wheels to make them move faster. These micro switches are more common in electric golf carts.
How does a gas golf cart start?
In gas golf carts, a micro switch located on the accelerator pedal triggers a signal that will start the cart’s engine. The cart will run without any problem as long as this micro switch remains active.
Why does my golf cart run when I hold the wire?
If the cart runs when you hold the wire on the solenoid posts, then the issue is with the cable connection. You should check this in both the Forward and Reverse position of the F & R switch.
How to fix a Yamaha G29 golf cart pedal switch problem?
In the G29 Yamaha golf cart, the pedal switch could be the issue. You should check it thoroughly. One quick way to do this is to press the pedal right up to the floor and remove your foot in a quick motion allowing the pedal to spring back to its original position in one stroke. Sometimes, this action can sort out the issue.
What does a micro switch do on a gas golf cart?
Microswitches are used in many golf cart applications. They are used at the accelerator pedal to provide a signal to the solenoid that you have depressed the pedal and are ready to go. In an electric golf cart, the solenoid sends power to the controller to move the cart.
How does a micro switch work?
Micro Switches have an actuator which, when depressed, lifts a lever to move the contacts into the required position. Micro switches often make a “clicking” sound when pressed this informs the user of the actuation. Micro switches often contain fixing holes so that they can be easily mounted and secured into place.
How do you test a micro switch on a gas golf cart?
Again, leave your black probe on the battery negative terminal and use your red probe for testing. With the key switch ON, you should read battery voltage at the common terminal (C or COM), but not the other terminal. Once the micro switch is activated, you should read voltage on both terminals.
How do you bypass a micro switch?
2:273:45How to create a jumper wire and bypass a safety switch in your Pellet ...YouTubeStart of suggested clipEnd of suggested clipSo I'm just going to use my jumper wire. And we're just going to plug in each end of the leads thatMoreSo I'm just going to use my jumper wire. And we're just going to plug in each end of the leads that went to the vacuum. Switch. Just like that. So now I have successfully bypassed my vacuum switch.
How do you test a micro switch?
2:134:10Electric shower problems: How to test a microswitch. - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is the normal micro switch and normally. The power comes in the top connection. Here and whenMoreThis is the normal micro switch and normally. The power comes in the top connection. Here and when the buttons pressed it goes out here and off to the elements or whatever.
How do you hook up a micro switch?
1:155:14How to Wire up a Micro Switch - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe negative of the power source should then go to the other end of the component. To turn somethingMoreThe negative of the power source should then go to the other end of the component. To turn something off when the switch is pressed the power source wire should go to the normally closed.
How do you bypass a micro switch on a golf cart?
You can bypass the reed switch in an EZGO golf cart by connecting the red wire of the reed switch to the white wire from the charger receptacles and to the red wire from the FRN micro switch.
Where is the micro switch on a Yamaha golf cart?
In a golf cart, you're going to find a large number of these switches throughout its build. For example, there is a micro switch located on the accelerator pedal. This switch activates when you push the pedal and sends a signal to the solenoid.
What does the reed switch do on a golf cart?
Reed Switches are used to prevent cart operation with the charger plugged in. They have become increasingly expensive and they are very fragile. this component is used to eliminate the reed switch from the electrical system.
Why do micro switches fail?
The faults that can affect a micro switch are components getting burnt, low quality components/parts, depreciation, when the switch works and stops suddenly. Although there are other faults, it has been discovered that over 70% of micro switches usually experienced these issues.
What does a micro switch look like?
0:224:00Understanding a Microswitch - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's better known as a snap action switch. Because it uses a spring to open and close connectionsMoreIt's better known as a snap action switch. Because it uses a spring to open and close connections inside of it if you move the lever on a good switch you can hear the spring snap back and forth.
How do you bypass a momentary switch?
You should try this first: keep the middle button pressed all the time, then switch the power on. Then, with the middle button still pressed, check if the other buttons still work.
What is a golf cart go switch?
On your golf cart, this high powered circuit is either your ignition on a gas golf cart or your electrical motor power circuit for an electric golf cart. Basically it’s your golf cart’s go switch, and it’s absolutely essential to your golf cart’s ability to do its job. Golf cart solenoids are also typically one of the first components ...
What is a micro switch on a gas pedal?
This switch is what sends the low power to the solenoid. The solenoid uses this to create a circuit between the battery and the starter, thus starting your motor and getting you grooving.
Why does my golf cart have no solenoid?
Golf cart solenoids are also typically one of the first components to fail in your golf cart, because they work very hard, turning on and off every time you stop and go in your golf cart. If you have an issue with no start or no go then your solenoid should be pretty high on your list of things to check.
What happens if a solenoid reads infinity?
If it reads infinity or open lead, then the solenoid has an internal fault and requires replacement. Your solenoid should also have a range that it operates in, and if the resistance reads outside of that range, you should replace the solenoid even if it works to avoid damaging other components.
What is a solenoid on a golf cart?
A solenoid, for our purposes, is a type of relay. A relay is a type of switch that uses a low power circuit to operate a high power circuit. A solenoid uses a magnetic coil (the actual solenoid) on a low power circuit to push a rod that closes a high power circuit. On your golf cart, this high powered circuit is either your ignition on ...
What is the most important part of a golf cart?
One of the most important components of your golf cart is the solenoid. It is one of the main components of your golf cart that allows it to move. Whether you have a Yamaha, E-Z-GO, or Club Car golf cart, and no matter if it is an electric or gas golf cart, you need a properly operating solenoid to get anywhere. Contents [ show]
How does an inductive throttle sensor work?
So you push the pedal down, and your inductive throttle sensor makes its first signal. This will activate the speed controller and solenoid. The way this works is a relatively low powered circuit is made with the low side of the solenoid.
Why does my golf cart micro switch stop working?
A bumpy ride, a wrong wiring or a defective component can cause the micro switch to stop performing as expected. A list of common problems associated with micro switches in a golf cart is given below. The mechanical switch gets stuck and doesn’t turn over when charged.
Where are the switches on an EZGO golf cart?
Most of the micro switches on EZGO golf carts including the EZGO TXT, EZGO RXV, and EZGO Express are located beneath the cart near the chassis. You have to unscrew the cover and access the switches.
How to bypass a reed switch on an EZGO golf cart?
To bypass the reed switch, remove the reed switch and install an eyelet on the white wire that was cut short in step 3. Connect the new eyelet to the A+ terminal of the charger receptacle which was opened in step 2. The above steps ensure that the reed switch is safely bypassed on your EZGO golf cart.
What is a forward neutral reverse switch?
The forward-neutral-reverse switch on a golf cart is a micro switch that is triggered when the golf cart is supposed to move in the reverse direction. It will trigger a buzzer that will indicate the golf cart’s reverse movement.
Why does my EZGO golf cart stop?
EZGO golf carts tend to stop and start while running when there is a problem with the micro switch. In case you face any of these troubles in your golf cart, the first thing you should do is test the micro switches in your golf cart and have them fixed at the earliest.
How does a golf cart accelerator work?
Accelerates the golf cart. A micro switch on the accelerator pedal gets activated once the pedal is pushed. This sends a signal to the solenoid and in turn more power to your wheels to make them move faster. These micro switches are more common in electric golf carts.
What is a micro switch?
The micro switches on a golf cart are used to control and protect the components through electrical signals. Micro switches play a critical role in the acceleration and reversing of a golf cart. To make the golf carts lightweight, most of the makers including Club Car, EZGO, and Yamaha have increased the usage of micro switches in their golf carts.
Why is my Yamaha golf cart not moving?
The main cause of a Yamaha golf cart clicking but not moving, is a faulty controller or solenoid. The battery has to be checked first to see if it’s delivering the right voltage while in the idle state as well as when the pedal is pressed. There can be other reasons for the Yamaha golf cart not moving though you hear the click.
What to do if your G9 golf cart is not clicking?
If you find your G9 Yamaha golf cart not starting nor clicking, check the key components for damage. If you find the parts to in good condition, check the brushes in the starter/generator.
How to check solenoid on G9 Yamaha?
The solenoid can be checked using an old screwdriver to jump the terminals. Your G9 Yamaha golf cart’s key must be in the start position. If the starter turns when you do this, your solenoid needs to be replaced. You must be careful while doing this crude test; there could be sparks when the two terminals touch.
Why do you need a wiring diagram?
A clear wiring diagram will help in ensuring that the cables are properly reconnected if you remove them for testing. In the solenoid, for example, the contacts inside can get jammed over a period. These have to be checked, cleaned, and re-fixed. If it still doesn’t work it has to be replaced.
Loose Cables
Loose power cable connections are the primary culprit in the failure of traditional mechanical rotary style forward reverse switches. Power cables are the thicker, usually 6-gauge, cables that connect the forward reverse switches to the starter generator, in the case of 2-cycle gas golf carts.
OEM 6 Gauge
For most golfing applications 6-gauge cabling is adequate to the task of carrying two golfers and their two golf bags around the course, stopping every 200 yards or so while they play their next shot.
Upgrades
The larger diameter tires require more current (amps) to simply get the cart rolling. Added passengers mean more pay load demanding still more amps through the electrical system. Add a hilly or mountainous terrain and the amp draw just keeps getting higher.
Sepex Controllers
Many modern golf carts have an electronic speed controller that handles the forward and reverse switching function internally. These carts have a toggle switch of some design to change direction rather than the older mechanical rotary forward reverse switches common to many golf carts.