Why is my EZGO carburetor smoking?
The exhaust emanates black smoke because the engine utilizes excess fuel or runs rich. The golf cart experiences hard starting because of an improper air-fuel ratio. The table given below offers some tips to troubleshoot your EZGO golf cart carburetor.
How do you adjust the carburetor on a Yamaha golf cart?
How to Adjust Yamaha Golf Cart Carburetor Yamaha G9 Carburetor Adjustment. Pull out the pilot adjustment screw. It must be present at a sharp point and not a flat spot. Rethread the screw back until it’s slightly seated. Turn the screw outwards by 1-1/2 turns. Push the throttle stop screw backward until the throttle shaft is closed completely.
How to troubleshoot golf cart carburetor problems?
Troubleshooting Golf Cart Carburetor Problems 1 Dirt in carburetor 2 Block in gas or air filter 3 Contamination in filter, hoses or gas tank 4 Clean up carburetor 5 Replace filter 6 Replace or clean components
How do you adjust the carburetor on a 2004 ezgomci engine?
2004 EZGOMCI Engine Carburetor Adjustment Adjust the jet pilot screw on the carburetor by doing a 1/4 turn on it. Do a valve clearance adjustment for both the outer intake valves and the inner exhaust valves. The inner exhaust valves and the outer intake valves must have a clearance of 0.004 mm.
How do you adjust the throttle cable on a golf cart?
Loosen the throttle cable present in the cable box to adjust the extent to which you can take it out of the housing. Press the accelerator so that the golf cart starts up and begins to idle. Check the cable tension to make sure that it's still loose. The idle screw can be used to adjust the idling if it's very fast.
How do you hook up battery cables to a golf cart?
The main positive lead for the battery bank coming from the frame of the cart will connect to the positive terminal of the first battery in the bank. Then, connect a cable from the negative terminal of the first battery to the positive terminal of the subsequent battery in the bank.
How do you hook up a golf cart engine?
4:155:58EZGO RXV Golf Cart Motor Removal & Installation How-To - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst we're going to run our main drive wires back to the front of the golf cart and the controller.MoreFirst we're going to run our main drive wires back to the front of the golf cart and the controller. Next we'll install our cable. Connectors. Not forgetting our motor.
How do you adjust the carburetor on a EZ Go golf cart?
2 Cycle engine: The adjustment screw is on the side of the carburetor and is parallel to the ground. You can identify it by the lock nut at the base of the screw. Loosen this and turn the screw all the way into a soft seat, then back it out one and a half (1-1/2) turns.
How do you hook up 12 volt batteries in a golf cart?
1:193:39Using 12v Batteries in a 48v Golf Cart, instead of 8 / 6 volt ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then positive to negative positive to negative positive to negative and then positive to theMoreAnd then positive to negative positive to negative positive to negative and then positive to the motor and by hooking them up in series you simply add up the volts.
How are electric golf carts wired?
Technically, most electric golf cart battery banks use series wiring. The 36-volts club car golf cart wiring requires a set of six batteries of 6 volts capacity each. You will also need five equal size connection cables.
What are the 4 terminals on a golf cart motor?
If you're unsure if it is working, it is simple to test. There are four terminals on a solenoid: usually two large and two small. The small terminals are connected to the battery, and the large terminals are connected to the motor. Disconnect all wires from the two large terminals.
How do you fix a gas golf cart that won't start?
First, try this: turn the key switch on, hit the accelerator, and check for a clicking noise. If you don't hear clicking, it's time to take a look at your cart's batteries. Make sure the battery is fully charged and the terminals are cleaned and secure. Next, see how the water level in the battery is holding up.
What causes a golf cart not to start?
As the main source of power to your electric golf cart, the batteries are commonly the cause for why your electric golf cart won't start. Acid-based batteries are typically used for electric golf carts and must be recharged in order to work properly.
Why does my golf cart only run with the choke on?
Dwight Coleman there are usually only a few possibilities if it only runs with the choke. One cause could be an air leak on the carb, head gasket, crankshaft seal. The other could be a clogged low speed and idle circuit.
How do you adjust a carburetor on a gas golf cart?
Find the pilot adjustment screw on the edge of your carburetor. Pay attention to this screw – it should be a sharp point and not flat. Carefully remove this screw and then carefully screw it back. Turn this screw out one and one-half turns to adjust it properly.
How do I speed up my EZ Go gas golf cart?
One way to increase the speed of EZ Go golf carts is to incorporate an octane booster when you fill the tank. The cart will have more pick-up, and it could gain as much as 5 mph. A different approach is to take out the throttle linkage governor on the carburetor.
Special offers and product promotions
Amazon Business: Make the most of your Amazon Business account with exclusive tools and savings. Login now
Have a question?
There was a problem completing your request. Please try your search again later.
How to adjust carburetor on golf cart?
In most cases, you’ll need to adjust the jet pilot screw, perform a valve clearance adjustment and then clean the carburetor.
How to remove cable from carburetor?
Remove the cable from the carburetor and cover its sheath opening using duct tape. To do this, make a small funnel with the tape and ensure that the wire sticks out from its middle. Loosen the nut that fixes the cable on to the mount housed on the motor just before its entry into the carburetor.
How to replace carburetor float?
Remove the carburetor and turn it upside down. Remove the nut that is used to secure the bowl on. Check the float for a puncture as this prevents the activation of the fuel cut-off needle valve. Replace the float if there is a puncture. Check for dirt accumulation in the needle valve.
Why does an EFI carb require more maintenance than an EFI?
The carb requires more maintenance than an EFI because of the cleaning and rebuilding of the carburetor involved.
Why does my carburetor flood on my golf cart?
The reason why a carburetor floods on a golf cart is usually due to a faulty fuel pump. The pump must be repaired or replaced accordingly. Seek professional assistance if required. This is usually due to the proximity of the fuel line to an exhaust manifold, a radiator hose or a heat source.
How to cool down a golf cart?
Procedure. Turn off the golf cart engine and allow it to cool for a couple of hours before you start working. This cooling down prevents damage to the cart and injury to yourself when you’re at work. Turn off the fuel-supply valve and remove the fuel line to prevent flooding of the fuel and other complications.
Which is more powerful, carb or EFI?
The carb model is more powerful as well as starts and goes faster when compared to the EFI. The EFI experiences delay to start moving when the pedal is pressed.
For the 295cc or a 350cc twin-cylinder OHC engine. 1991 – Present
Tools required: Ratchet with 6″ extension, 10mm socket, 10mm socket wrench, flat blade screwdriver, and a feeler gauge. Note: if the screw (C) has a square head instead of a flat blade slot, this takes a tool designed just for this purpose.
For the Kawasaki FJ400 401cc 4-cycle Single Cylinder 1996 – Present
Tools required: Ratchet with 6″ extension, 10mm socket, 3mm hex wrench, feeler gauge.