Tap the center pins of the rivets so they are flush with the rivet body. Use #10 x 1/2" Stainless Steel Screws to affix the plate to the mounting bracket. You can see slight indentations where the screws are to go.
Full Answer
How do you mount a front license plate?
They are right-angle metal brackets that screw into a downward-facing part of your car's nose and then offer a forward-facing metal plate to attach your plate to. If you remove the mount later, no holes will be visible. A right angle bracket allows you to drill unseen holes in your car to mount a front plate.
How many holes does a front license plate holder have?
Original owners state was rear plate only. Looking at the OE holder, seems to require 5 holes. Most holders just need a pilot hole and the screws hold it on. This holder has sort of a plastic molly/ anchor thing going on.
What is a right angle bracket for front license plate?
A right angle bracket allows you to drill unseen holes in your car to mount a front plate. Don't be fooled by these; they aren't meant for the kind of license plate mounting you're trying to do. These are temporary mounts for car dealers and test drives.
Do I need a front plate holder on my sport wagon?
My new to me 14 sport wagon needs the front plate holder installed. Original owners state was rear plate only. Looking at the OE holder, seems to require 5 holes. Most holders just need a pilot hole and the screws hold it on.

How do you put a front license plate on a Volkswagen?
0:445:09How To Install a Front License Plate - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust go ahead and go down into the center from that point i've already drilled the holes in here butMoreJust go ahead and go down into the center from that point i've already drilled the holes in here but i'll tell you how i went about doing it all you want to do is get a little bit of masking tape.
How do you attach a front license plate?
Drive screws clockwise through the bracket into the bumper. Screw the license plate onto the bracket. After mounting the bracket, line the holes at the corners of the license plate with those at the bracket's corners. Drive screws clockwise through the holes to secure the license plate and complete installation.
How do you mount a front license plate without drilling holes?
0:506:10Don't drill your bumper to attach that plate. Easy method. - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut what we have is two pieces of sticky. Back velcro. We're going to stick these on the licenseMoreBut what we have is two pieces of sticky. Back velcro. We're going to stick these on the license plate and then we'll peel the other side off and put it on the car.
How do you mount a front plate holder?
0:463:31How to Install a Removable Front License Plate Bracket - YouTubeYouTubeStart of suggested clipEnd of suggested clipThese are the tools you need to install it a 10 millimeter socket with ratchet Phillips screwdriverMoreThese are the tools you need to install it a 10 millimeter socket with ratchet Phillips screwdriver 10 millimeter wrench non permanent marker and 1/8 inch drill bit and drill.
What screws for front license plate?
The standard license plate screw size for many vehicles is 1/4-14-3/4-inch self-tapping screws that especially fit vehicles with plastic or nylon screw retainers.
How do you put a license plate back on without screws?
0:286:58attach License plates / Number plates with no holes DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhat it is is it's a double-sided tape. But it's a Velcro as such it's a matching velcro. So you donMoreWhat it is is it's a double-sided tape. But it's a Velcro as such it's a matching velcro. So you don't need one loop side and one hook side it's essentially two of the same.
Will Velcro hold a license plate?
To answer your question, the Velcro WILL hold up fine BUT you may have a problem if you ever want to get the part attatched to the paintwork back off again. However if you have the clearbra then that wouldn't be a problem as the clearbra would come off instead.
How do you install a license plate bracket?
0:342:15Simple front license plate bracket install! - YouTubeYouTubeStart of suggested clipEnd of suggested clipBecause it's Texas. So first thing we're gonna do is we're gonna get measured out where the licenseMoreBecause it's Texas. So first thing we're gonna do is we're gonna get measured out where the license plate bracket is gonna go on the car. Get some tape on there get the holes marked out and get them
How do you drill a number plate without cracking it?
Drill Holes Carefully Start the drill and gently begin to make a hole. Allow the bit to do the work, avoid applying to much pressure. Remember: Drill from the rear of number plate to the front. Placing wood underneath the number plate might help avoid damage.
Step 2
Position the license plate frame and center it on the VW emblem and parking camera (below, if installed). You can use the vertical supports in the lower grill (hard to see in this pic) to assist in alignment.
Step 5
Tap the center pins of the rivets so they are flush with the rivet body.
Why do we need front plates?
Front plates can also help the average person ID a car behind them in their mirror, or one that is otherwise only seen from the front, like a car turning across you in an intersection.
What does the California front plate say?
We can't cover every state's statutes, but in California, the state with the most cars, the vehicle code says a front plate must be: Securely fastened. Clearly visible. (Those two alone will likely get you a ticket if you try the common trick of just tossing your plate on your dash.)
Why are front plates hated?
Why front plates are hated. The reasons are many: Carmakers seldom create a nice well for a front plate the way they do for rear plates. As a result the front plate usually looks tacked on. The Honda HR-V offers a clean, well-lighted place for a rear license plate. On the front, nothing.
What is a right angle mount?
Right-angle mount. These still require you drill holes in the front of your car, but not in a place that will be seen. They are right-angle metal brackets that screw into a downward-facing part of your car's nose and then offer a forward-facing metal plate to attach your plate to. If you remove the mount later, no holes will be visible.
Do you have to drill holes in your bumper?
Here are the US states where you don't need an ugly front license plate. Everyone else, read on. Mapchart.net. Now playing:
Is the adhesive plate real?
The adhesive plate, shown below the original metal one, does a good job of looking just like your real plate, but it isn't. Since they are the correct size, an exact replica of your state's plate design, and carry your license plate number, they might fool a lot of people from 20 feet away.
Do front plates have registration stickers?
Front plates often don't carry registration stickers, so many drivers find them superfluous. Some cars are designed so that a front plate must be mounted smack over the grille of the car, looking ugly and disturbing airflow.
