EZGO pulser coil location The location of the pulser coil is under the cart’s seat and is near the engine. It is better to use a user manual to locate the coil so that it can be tested or replaced.
How do I check the ignition coil on a EZGO golf cart?
To check the ignition coil on a 1991 to 2002 4 Cycle EZGO Gas golf cart you will need a multimeter capable of reading ohms Ω With the coil completely disconnected perform the following tests
What are coils on an electric golf cart?
Coils are not a part of the electrical system of electric golf carts, but rather are part of gasoline-powered carts and their ignition system for firing the spark plugs.
How to replace the igniter coil on a golf cart?
Switch the coil wires to adjust the pulser. If the pulser coil is damaged, then there is only one thing left to do, which is to replace the coil. Igniter coils can’t be repaired so removing the older ones and replacing the same with a new one is crucial. The pulser coil can be removed while the engine is still placed in the cart.
How do you mount a coil on a golf cart battery?
Golf cart manufacturers all mount their coils in slightly different locations. It is black and cylindrical with a metal heat sink on each side and will have a single, thin wire coming out of one end and a thicker wire coming out of the other end. Disconnect the negative terminal from the golf cart's battery using a wrench.
How do you check a coil on a golf cart?
Take the voltmeter's black and red probe and place it on the –ve and +ve terminal of the coil. Take the readings. It should be between 3.7-5.2 ohms. If outside the range, the coil should be replaced.
What does the igniter do on an EZGO golf cart?
This part is designed to help produce the proper electrical signal to get your cart's engine running and to keep it properly moving without any issue. In essence, the ignitor works to enhance electrical signals and produce a larger flow of electricity to the coil that helps your spark plug operate.
How do I test my EZGO coil?
Attach the red lead to the positive terminal. Select the "Ohm" setting on your volt/ohm meter and read the display. The golf cart coil should register as more than 3.7 ohms, but less than 5.2 ohms. If the coil registers outside this range, replace the coil with a new unit.
How do you remove the ignition switch on a EZGO golf cart?
How to Replace the Ignition Switch on EZGO Golf CartUse a wrench to disconnect the battery cables.You will also need a small screwdriver to remove the rivets holding the ignition console in place.Remove the face nuts with a pair of pliers. ... Install the new switch on to the plate and screw the face.More items...
What is a coil on a golf cart?
Ignition coils transfer voltage from your battery into spark for your engine to fire. We carry ignition coils for EZGO TXT, RXV, Marathon, and ST350 Workhorse golf cart models.
Why is my golf cart not firing?
First, try this: turn the key switch on, hit the accelerator, and check for a clicking noise. If you don't hear clicking, it's time to take a look at your cart's batteries. Make sure the battery is fully charged and the terminals are cleaned and secure. Next, see how the water level in the battery is holding up.
How do you test a ignition coil?
1:525:53How to Test Ignition Coils - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd simple test that can be done you use a circuit test which is also called a test lighting. AndMoreAnd simple test that can be done you use a circuit test which is also called a test lighting. And what you do you connect the negative up to the negative cable still disconnected.
Why does my ezgo golf cart not move?
The main reason why a EZGO gas golf cart will not go forward is because of a locked up brake, or a faulty solenoid and accelerator. A defective Run/Tow or Forward/Reverse switch can also cause a EZGO to not move forward.
Why wont my golf cart go forward or reverse?
If the power from the battery pack is not reaching the motor, then the Club Car golf cart won't move forward or reverse. In such cases, there are a few components in between the two that need to be checked. The solenoid is one major component. Check if the resistor between the two big terminals on the solenoid is hot.
How do you test a ignition switch?
4:076:01How to test an ignition switch - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd make sure when I ground it out and any other position besides off. So as you can see on doesMoreAnd make sure when I ground it out and any other position besides off. So as you can see on does open that connection back up as well as your starting position.
How do you bypass a solenoid on a golf cart?
Bypassing Golf Cart Solenoid Method If you do decide to bypass the solenoid, this is what you need to do: Take the two larger wires that connect to the solenoid and connect them directly (keeping all safety precautions in place). This should do the trick and if it does not work then the solenoid is not the problem.
How do you test a ezgo directional switch?
Check all the connections and make sure each part is getting power by using the multimeter. Have your foot firmly on the brake, put in the key, and the F/R switch in the forward position. When you push the go pedal if the solenoid charges up then your EZGO F/R switch is good to go.