- Determine how much of the shaft’s tip you wish to trim. ...
- Place the shaft into a rubber golf club clamp, then insert the clamp into a vise. The rubber protects the graphite from damage.
- Wrap two or three layers of masking or electrical tape around the area to be cut. The tape helps prevent the shaft from splintering.
- Measure the distance that you wish to trim from the tip, then mark the distance on the tape with a pen.
- Cut carefully along the marked line with a hacksaw, insuring your blade is perpendicular to the shaft.
- Determine how much length must be trimmed from the butt end of the club. This typically depends on the type of club you're constructing.
Full Answer
How do you glue a graphite Golf Club shaft?
Steps to Remove a Graphite Shaft:
- Keep the shaft in a graphite shaft extractor following the instructions given for the extractor.
- Apply heat on the hosel with a heat gun.
- Use a box wrench to turn the threaded bolt of the extractor without twisting the clubhead.
Which blade to cut a graphite shaft?
- Vise
- Hack Saw with Blade to Cut Graphite
- Dremel Tool
- Masking Tape
- Yard Stick, Ruler
- Marker
How to coat steel with graphite?
- Improved uniformity
- Improved material consistency
- Improved lifetime
- Higher chip yields possible through improved photoluminescence
How to trim a golf club shaft?
To do that, the DIY golfer will have to:
- Remove the existing grip.
- With steel shafts, use a tubing cutter to trim the shaft; with graphite shafts, shorten using a hacksaw.
- Re-install a grip on the newly shortened shaft.
- And, most importantly, Wishon says, add weight to the clubhead in some manner to restore the swingweight feel of the club. ...
Can graphite shafts be cut down?
Yes, it is even strong enough to cut steel. It can cut through a graphite shaft in 15-20 seconds after the shaft has been securely place in your vise. The model we sell fits on a standard 12” hacksaw frame found at any hardware store or in many home shops.
What can I use to cut a graphite golf shaft?
1:2914:05Golf Club Repair - How To cut a Golf Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipThat's what we're going to talk about so two kinds of shafts right we got steel. And we haveMoreThat's what we're going to talk about so two kinds of shafts right we got steel. And we have graphite we're going to talk about steel. First alright the the easiest most cleanest way to do it by hand
How do you shorten a graphite driver shaft?
With steel shafts, use a tubing cutter to trim the shaft; with graphite shafts, shorten using a hacksaw. Re-install a grip on the newly shortened shaft.
Can I use a pipe cutter on graphite shaft?
0:002:12HOW NOT TO CUT GRAPHITE GOLF SHAFTS / Wrong Tool for the JobYouTubeStart of suggested clipEnd of suggested clipSo i've had a few different people ask me can i use the pipe cutter that we used in the steelMoreSo i've had a few different people ask me can i use the pipe cutter that we used in the steel shafted assembly video on graphite. And the answer is emphatically no and i'm going to show you real quick
How much does it cost to cut a golf shaft?
Any amount of cutting will slightly stiffen the club. It will probably go unnoticed if you take 1 inch or less off the club. Taking 2 inches off will change the flex of the club. If you are shortening irons, every 1 inch you shorten the club will make the iron effectively play 2 degrees flatter.
How do you shorten graphite clubs?
0:394:01How to Cut Golf Shaft DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo for the first step you have to remove your old grip. I find the easiest way to do this is toMoreSo for the first step you have to remove your old grip. I find the easiest way to do this is to literally just cut a line all the way down your club.
Can I cut my driver shaft down?
Shortening the shaft will make the club shorter but it will also make the shaft stiffer and adjust the swing weight as well. Plus, the more length you remove, the less flex your club will have. Depending on how much you cut it down, it could move a regular flex to a stiff or a stiff to an extra stiff.
How much does it cost to shorten a driver shaft?
Generally, this fee will be about $15 to $35 depending on where and when you get the work done. Replacing a shaft on a driver is a bit more work than regripping a club.
How long should your driver be based on height?
Tony Finau is one of the tallest golfers on the PGA Tour at 6'4″, and his driver's length is usually around 45 inches. Both Finau and Fowler are two of the longest drivers on the PGA Tour....Driver Shaft Length Based Solely on Height.Height (feet/inches)Driver Shaft Length5'0″-5'2″44.5″4'10”-5'0″44″< 4'10”43″7 more rows•May 9, 2021
How do you cut a golf shaft?
The butt end of the shaft is grip end. If you are shortening or extending the length of a golf club, this is where you will cut. If you want to change the play-ability of the club (feel, flex to a certain extent, spin rate, dispersion), you will be cutting the tip end of the shaft.Jan 3, 2021How to cut a golf shaft | The DIY Golferhttps://www.thediygolfer.com › how-to-cut-a-golf-shafthttps://www.thediygolfer.com › how-to-cut-a-golf-shaftSearch for: Which end of a golf shaft do you cut?
What happens when you shorten a golf club?
Tipping any TPT Red Range shaft 1 inch will result in a stiffness increase of 5 cycles per minute (cpm), or one-half flex. This removes the need for half flexes in the Red Range. When a 14 Lo is tipped 1 inch, for example, it effectively becomes a 13.5 Lo.TPT Shaft Tipping 101: How And Why To Tiphttps://tptgolf.com › learn › tpt-shaft-tipping-101https://tptgolf.com › learn › tpt-shaft-tipping-101Search for: How much does tipping a shaft effect Flex?
Step 1: Prepare tools
Preparing your tools is the first step but will contribute to your success. If you prepare incorrectly or lack the tools, it will take time in the process.
Step 2: Measure and mark
Measuring and marking will help you know exactly where to cut and make them more specific. It is impossible to guarantee that you will be satisfied with the first measurement results.
Step 3: Prepare to cut
After you have determined the point you want to cut, do not rush to pick up the knife to cut it. It would help if you prepared a little more to make the cutting process more convenient and safe for yourself.
Step 4: Cut a graphite golf shaft
After a complicated preparation process, now you have come to the most critical step: cut a graphite golf shaft. However, you do not need to worry too much if you have carefully prepared the above steps.
Step 5: Check the cut
The process of cutting a graphite golf shaft is almost complete. Now you just need to double-check that the cut is exactly what you want, and you can use it.
Remove the Grip
The first things to do is to remove the grip tape from the golf club [how to remove grip tape from golf club]. This will make it easier to cut the shaft. You can use a cutter to slice the grip from the top and slowly peel it off the club. The specific process can differ, which will depend on the material of the grip.
Measure the Shaft
With the grip now off the golf club, the next step is to take the appropriate measurement. Use a measuring tape and run it from the top to the bottom of the shaft. Mark the specific spot where the measurement ends. You can do this with a marker or by wrapping the tape around the tip. The measurements should be as precise as possible.
Cut the Shaft
Now comes the most important part of the task. Before cutting the shaft, make sure that it is in a stable position. Some might think that they can cut by holding the shaft with one hand, but this isn’t the case. For your safety and to make the cut more accurate, we recommend placing the golf club in a vise.
Wrap a Grip Tape
Once you are done cutting, the next step is to wrap it using your grip of choice. Pick a material you are comfortable with. This is important since it is the part that you will be holding, and hence, it will affect how you swing the club. Also, it must absorb vibration, making sure of your highest level of comfort, even during aggressive shots.
What is the difference between a golf shaft and a tip?
All golf shafts taper; that is, their circumference is greater at the grip end than at the tip end. That means that the grip end is the strongest part of the shaft and the tip end the weakest, which, Wishon says, leads trimming to have different effects: "Cutting more of the tip will have the effect of getting rid of some of the weaker end ...
How to shorten a golf club shaft?
To do that, the DIY golfer will have to: 1 Remove the existing grip. 2 With steel shafts, use a tubing cutter to trim the shaft; with graphite shafts, shorten using a hacksaw. 3 Re-install a grip on the newly shortened shaft. 4 And, most importantly, Wishon says, add weight to the clubhead in some manner to restore the swingweight feel of the club. "If clubs are shortened and no weight is added back to the clubhead, the chances of the length reduction having the desired effect are somewhere between slim and none."
Who is Tom Wishon?
To answer these questions, we spoke with prominent golf club designer and builder Tom Wishon, founder of Tom Wishon Golf Technology. Wishon explained: "When golf shafts are manufactured and shipped to clubmakers and clubmaking companies, they are in what is called a raw, uncut form.
Should the reduction in length be made from the grip end only?
"If the goal in making the clubs shorter in length is a desire to gain an improvement in accuracy, the reduction in length should be made from the grip end only ," Wishon said.
Why use masking tape on graphite shafts?
Secondly, by wrapping tape around the shaft, reduces the likelihood that the shaft would splinter during the last moment of the cutting process.
What is a rod saw blade?
Even for veteran clubmakers, the rod saw blade is handy to cut a single shaft instead of firing up your motorized equipment or to find that you have a damaged blade in need of replacement. Plus it comes in handy cutting the shaft angle and through bore plugs for those golf club thru bore installations. All-in-all, it is a long-lasting tool no golf ...
Can you cut graphite shafts?
Graphite shafts need special care to be cut properly. A tubing cutter, that you would use to manually cut a steel golf shaft, will crack or destroy a graphite shaft in no time at all. Don’t think about pulling the hacksaw from your tool chest either.
Can a hacksaw cut steel?
Yes, it is even strong enough to cut steel. It can cut through a graphite shaft in 15-20 seconds after the shaft has been securely place in your vise. The model we sell fits on a standard 12” hacksaw frame found at any hardware store or in many home shops. How To Tips. I would like to share a few how-to tips as well.
Can a rod saw blade cut steel?
It makes thin straight cuts in all types of shaft materials used in golf. Yes, it is even strong enough to cut steel.
Feedback
Hey guys. I want to cut a half inch off my driver shaft. I've done a lot of searching but am not finding a definitive answer. I know you need to wrap the area you're cutting in masking tape but what's not clear to me is the correct type of blade to use. Some say hacksaw, others say a chop saw (which I have to admit, I have no idea what that is).
Feedback
i've used a dremel -- or a chop saw. either work fine. hacksaws COULD splinter the ends --not sure if it's 100% true but, i'd rather not risk it.
Feedback
I used a miter box and hacksaw with a blade with the highest number of teeth per inch (TPI) I could find at the hardware store. Came out just fine.
Feedback
What is a chop saw? I have a dremel but what attachment should be used? Also, if using a dremel, how do you get the cut perfectly straight?
Feedback
I'll use anything that has fine sharp teeth. I've done most of my shafts by hand recently because I have limited space and its easier without needing electricity and cords.
Feedback
Dremel cutoff wheel. They use a similar abrasive material circular saw blade as a chop saws uses (which is what you will find at a club maker for cutting graphite shafts). I use it for my graphite shafts as well as my carbon fiber arrows for my compound bow. Never had problems with either.
Feedback
Chop saw is best, Dremel with cutoff wheel will work (but it is tough to make an even cut), and if you use a hacksaw get a 'grit' blade.
Step 1
Determine how much of the shaft’s tip you wish to trim. The graphite shaft will come with trimming instructions that tell you how much to cut from the tip, depending on the amount of flex you want. For example, you’ll trim more off the tip to achieve a stiffer flex.
Step 2
Place the shaft into a rubber golf club clamp, then insert the clamp into a vise. The rubber protects the graphite from damage.
Step 3
Wrap two or three layers of masking or electrical tape around the area to be cut. The tape helps prevent the shaft from splintering.
Step 4
Measure the distance that you wish to trim from the tip, then mark the distance on the tape with a pen.
Step 5
Cut carefully along the marked line with a hacksaw, insuring your blade is perpendicular to the shaft. The Clubmakers.co.kr site suggests using a grit edge blade in your saw.
Step 6
Determine how much length must be trimmed from the butt end of the club. This typically depends on the type of club you're constructing. For example, the standard length of a graphite men’s 5-iron is 38 inches, while a standard 9-iron is 36 inches long, according to the Clubmakers website.
Step 7
Tape and mark the area to be cut, as you did with the tip. However, add 1/8 inch to the cut to account for the grip cap. For example, if your 9-iron shaft is 38 inches long after trimming the tip, trim 2 1/8 inches from the butt end to produce a 36-inch club after the grip is installed.
Series Navigation
I know this might seem obvious, but be sure to measure and mark off the point at which you are cutting. Especially while tipping a shaft (you can’t undo this), it is important to have precise measurements. Use a sharpie to make your marks on the shaft. Here is a tutorial on how to measure golf clubs.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
