Golf-FAQ.com

how to extend a golf shaft

by Elisha Price Published 3 years ago Updated 2 years ago
image

  1. Never extend a steel shaft more than 2″. Any more may cause premature failure due to stress where the extension is made. ...
  2. We recommend using a steel extender to extend a steel shaft. Using other materials may lead to premature breakage. ...
  3. Always epoxy the extension in place, do not rely on a pressure fit.

More items...

Part of a video titled How to ADD Extensions To Golf Clubs - Start to Finish!
7:41
11:02
So I'm gonna take my ruler. And a pen. And I'm gonna measure out one inch. We're gonna grab our pipeMoreSo I'm gonna take my ruler. And a pen. And I'm gonna measure out one inch. We're gonna grab our pipe cutter put it right there on the mark. Tighten. It down. Cut so we are almost ready to regrip.

Full Answer

How do you shorten a golf club shaft?

To do that, the DIY golfer will have to:

  • Remove the existing grip.
  • With steel shafts, use a tubing cutter to trim the shaft; with graphite shafts, shorten using a hacksaw.
  • Re-install a grip on the newly shortened shaft.
  • And, most importantly, Wishon says, add weight to the clubhead in some manner to restore the swingweight feel of the club. ...

How to install a shaft in a golf club?

How to Install a Shaft in a Golf Club

  1. Remove the old shaft. It can be done by melting the glue, or epoxy, that holds the shaft to the head of the club.
  2. Cut the shaft to the proper length, depending on what club you are modifying. There are websites that can help you determine the length.
  3. Roughen the tip of your new shaft before inserting it into the hosel of the club head. ...

More items...

How do you replace a golf club shaft?

How To Re-Shaft Your Steel Golf Clubs

  1. Carefully clamp the shaft into a vise using a Shaft Vise Clamp. ...
  2. When removing steel shafts from clubheads, use a torch to heat the hosel. ...
  3. After 30 seconds of heating, with your gloved hands grasp the head and twist/pull the head. ...
  4. Using a wire brush remove excess epoxy from the inside of the hosel.

More items...

How much does it cost to reshaft a golf club?

So, how much does it cost to reshaft a golf club? To reshaft a golf club, you’re likely to spend between $20 to $200 per club. The cost of reshafting your golf clubs will vary greatly depending on where you go to have it done. The cost will depend on the cost of the labor, the number of clubs, and the cost of the new shafts.

image

Can you lengthen a golf shaft?

There are two ways to lengthen your shafts. You may add extenders to your existing shafts or you may replace your existing shafts with longer ones. The effects can be very different. Tom Wishon has written extensively about the effects of changing shafts in "The Golfsmith Practical Clubfitting Program" guide.

How do you extend a driver shaft?

1:352:35How To Install Graphite Shaft Extenders - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext is you want to carefully measure and mark the butt end of your extender and remember never goMoreNext is you want to carefully measure and mark the butt end of your extender and remember never go more than two inches except for a putter shaft.

How much does it cost to extend shafts?

Lengthen Shaft ($5.99 Steel or $6.99 Graphite per club*): Most irons, putters, and woods can have length added to the existing shaft. *Save grip Fee may apply.

How do you extend a graphite golf shaft?

1:386:17Billy Bobs Golf Training - Graphite and Metal Shaft Extentions - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnother way to make the shaft extensions fit is by using a drill press if you have a drill pressMoreAnother way to make the shaft extensions fit is by using a drill press if you have a drill press with an inch and a half Chuck. You can open it up and put the extension in it to hold it.

What height do you need longer golf clubs?

Your Height If you are taller than about 6'0”, you will likely need clubs that are a bit longer than normal. The standard golf clubs that come from the manufacturer are typically built to help golfers who are around 5'7” to 6'0”. If you are 6'4”, you can almost guarantee that you will need longer golf clubs.

What does it cost to lengthen golf clubs?

How much does it cost to lengthen golf clubs? On average, it will cost $8-9 per club plus the cost of a new grip to lengthen your clubs. If you're looking to save your old grips, you'll avoid the cost of new grips, but you'll have to pay a save grip fee of around $10 per club.

Is it worth Reshafting my irons?

Reshafting is just one way to keep your clubs performing at a high level. You can also benefit from regripping your clubs. Replacing worn-out golf grips can help make your clubs feel new again. Adding the right shaft to your favorite clubs can get you back on the course and working toward a new personal low round.

Can I change the shafts in my irons?

Yes, just like other types of golf clubs, golf irons can also be reshafted using a golf repair service.

How much is it to Reshaft a driver?

The cost of reshafting a golf driver is between $15 and $45 USD. The labor cost of reshafting is usually around $20 USD. However, the actual overall cost can also depend on the materials used as well as the type of grip and shaft you are looking at.

Do graphite shaft extensions work?

Graphite shaft extensions...they work! I purchased these to add some length to a set of graphite shafts. They worked but had to do a little bit of sanding to make them fit. But this would be preferable to having them start out a little loose.

What size shaft extender do I need?

First you'll need to measure the INSIDE diameter (ID) of the butt end of the shaft (not the outside). This will determine the size extension you need. Due to slight variations in shaft diameters, you will likely need to apply light sanding to the shaft extension to achieve a suitable fit.

How do I extend my golf irons?

8:2011:02How to ADD Extensions To Golf Clubs - Start to Finish! - YouTubeYouTubeStart of suggested clipEnd of suggested clipI use the narrow grip tape. So you're gonna have to use two pieces. Put there and then you grabMoreI use the narrow grip tape. So you're gonna have to use two pieces. Put there and then you grab another piece. And you put it on the top remembering. Don't let that half inch.

How does lengthening a shaft affect swing?

Timing and Feel. In many ways, the biggest effect of lengthening a club shaft is how it affects your ability to swing the club. The combined changes in length and swing weight make the club feel different. In turn, these changes will affect your timing and even your mechanics, perhaps without you even realizing it.

Do golf clubs have longer shafts?

Effects of Lengthening a Golf Club Shaft. Tall players like Bubba Watson have to use longer shafts in all of their clubs. Most players consider using longer shafts in their clubs at some time or another, believing that longer shafts equal more distance, although that isn't necessarily true. There are two ways to lengthen your shafts.

Can you add extenders to your golf shaft?

You may add extenders to your existing shafts or you may replace your existing shafts with longer ones. The effects can be very different. Tom Wishon has written extensively about the effects of changing shafts in "The Golfsmith Practical Clubfitting Program" guide.

Does lengthening the shaft make the club head heavier?

Lengthening the shaft increases the swing weight, which makes the club head feel heavier. It may even make the club too heavy for you, which will slow down your swing speed and actually reduce your distance.

Does lengthening a golf club shaft affect accuracy?

Accuracy. As a general rule, lengthening any club's shaft will reduce your accuracy with that club. The longer the club, the more difficult it becomes to hit the ball solidly. This is especially true when the ball is on the ground rather than on a tee, since hitting the ball fat is more likely.

Is shaft length a factor?

Shaft length is certainly a factor in how far you hit a given club. However, some clubs benefit more than others. Installing longer shafts in wedges and short irons will almost always result in more distance, as most players have little trouble swinging the shorter clubs.

Can you use extenders to lengthen a golf club?

However, using extenders to lengthen a club will change the flex of the club, sometimes by an unpredictable amount. Not only does the shaft become more flexible than before, thus further affecting accuracy, but it lowers the kick (or bend) ...

Feedback

At what length does a graphite shaft extension start compromising the integrity of the shaft, from a performance point of view? My uneducated guess would be anything under 1" wouldn't drastically affect performance, but once you get closer to 2", you start to mess with certain shaft properties. Anyone care to chime in?

Feedback

For the better players I don't go more than 1" I don't think it's worth it, however I strongly advise you to get a proper graphite extension not a wooden dowel as the Woden dowel will add more unwanted weight in the butt end and will also create a weak point in the current shaft where the dowel ends as the shaft won't be able to flex properly.

Feedback

I've personally have never seen this dowel method. I would recommend you use another scrap graphite shaft to glue into the butt end. after it all dries up, just simply trim to playing length and make up the difference in diameters with tape.

Feedback

I would use either a prescribed extension or cut an old graphite shaft as stated above...Personally, I don't ever go more than 1", although I'm sure you could go more than this an not impact the playing characteristics of the shaft...just personally, I don't like going more than 1"

Feedback

It's easy to shop-make a very strong and light extension: Find a piece of old broken graphite shaft which will just fit inside your current shaft - you want about 2" of insertion once the paint is cleaned off.

Feedback

Find a piece of old broken graphite shaft which will just fit inside your current shaft - you want about 2" of insertion once the paint is cleaned off. Now find another old piece of shaft which will fit OVER that inner piece - this will be your extension and ideally it's of similar OD to the butt of the existing shaft.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Mike C said

If done properly, you won't even know there is an extension, but it will decrease the swing weight of the club (i.e., the head will "feel' lighter). This isn't huge as the weight of the plug will be offset a little by the increased length of the shaft.

James T said

If done properly, you won't even know there is an extension, but it will decrease the swing weight of the club (i.e., the head will "feel' lighter). This isn't huge as the weight of the plug will be offset a little by the increased length of the shaft.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9