How to Shorten Golf Clubs
- Insert the golf club into a shaft clamp and tighten the clamp to keep the club from moving around while you work on the grip.
- Use a utility knife to cut the side of the existing grip. Pull off the grip and discard it. ...
- Wrap masking tape around the area of the shaft that will be cut. The tape will keep the end of the shaft from splintering as you cut.
- Insert the cutting blade attachment into the rotary tool according to the instructions in your owner's manual.
- Start at the end of the club and wrap grip tape around the shaft. Overlap the previous layer of tape slightly to keep it tight.
- Insert the pointed end of a golf tee into the hole at the end of the new grip. ...
- Place the grip over the end of the shaft and push it down before the solvent dries. ...
How do you shorten a golf club by 2 inches?
Taking 2 inches off will change the flex of the club. If you are shortening irons, every 1 inch you shorten the club will make the iron effectively play 2 degrees flatter. You may need to have the lie angles readjusted after shortening them. Remove the grip using a utility knife with a hook blade. Remove the grip tape from the shaft.
How can I hit my golf ball longer?
Many golfers strangle the grip, which keeps the face from turning over through impact and leads to a weak ball flight. Learn to let the toe rotate over the heel. Do it right and you’ll hit the ball a full club-length longer.
Should you swing your golf clubs long or short?
The problem with overswinging is that it can force a golfer out of his address posture, leading to an early release of the hands; this saps power and creates a poor impact position. So think “short” to go long. Here’s how.
How can I make my golf clubs longer?
Do it right and you’ll hit the ball a full club-length longer. Here’s how it’s done. Lay the handle diagonally across the base of your fingers, so that you don’t grip the club in your palm. This makes it easier to hinge and unhinge your wrists and rotate the clubhead more effortlessly.
How do I shorten my golf club length?
When shortening a golf club, you must remove the grip and cut the wide end of the shaft so the club can still flex properly.Insert the golf club into a shaft clamp and tighten the clamp to keep the club from moving around while you work on the grip.Use a utility knife to cut the side of the existing grip.More items...
Can you make irons shorter?
Any amount of cutting will slightly stiffen the club. It will probably go unnoticed if you take 1 inch or less off the club. Taking 2 inches off will change the flex of the club. If you are shortening irons, every 1 inch you shorten the club will make the iron effectively play 2 degrees flatter.
Can you shorten clubs?
Golf clubs are often sold in a “standard” length, which is relative to each club. However, golfers differ in height and arm length, so sometimes the length of a club must be adjusted. Not only can golf clubs be lengthened for people who need it, but they can also be shortened.
What happens if my golf clubs are too long?
What Happens When Golf Clubs Are Too Long? For most golfers, having clubs that are too long will result in the most inconsistent shots. Clubs that are too long will make you stand too upright, which can cause both heel and toe shots as well as a tendency to pull the ball.
Do pro golfers use shorter clubs?
Most pro golfers use shorter shafts on their drivers than recreational golfers. Is this true? Absolutely true.
Do you lose distance with shorter irons?
The most important thing to remember about the distance when you shorten your irons is that it does not always mean a decrease in distance. If your irons were too long for you to be confident or to have the right swing speed or posture, chances are you would gain distance if you shortened them.
What happens if I cut an inch off my driver?
Shortening the shaft will make the club shorter but it will also make the shaft stiffer and adjust the swing weight as well. Plus, the more length you remove, the less flex your club will have. Depending on how much you cut it down, it could move a regular flex to a stiff or a stiff to an extra stiff.
What is the standard height for golf clubs?
between 34 and 35.5 inchesSo What Is the Standard Golf Club Length? Based on the average wrist-to-floor measurement and overall height, the standard length of golf clubs is anywhere between 34 and 35.5 inches.
How long should your driver be based on height?
Tony Finau is one of the tallest golfers on the PGA Tour at 6'4″, and his driver's length is usually around 45 inches. Both Finau and Fowler are two of the longest drivers on the PGA Tour....Driver Shaft Length Based Solely on Height.Height (feet/inches)Driver Shaft Length5'0″-5'2″44.5″4'10”-5'0″44″< 4'10”43″7 more rows•May 9, 2021
How do you tell if your clubs are too long?
5 Signs Your Golf Clubs are Too LongYou need to stand up almost completely straight while holding the club.You can't move your lower body while swinging the golf club.You keep hitting the ball with the golf club's toe.The ball tends to veer off to the left or too high when hit by the club.More items...•
Is it OK to choke up on golf club?
0:401:37When Should you Choke Up on a Golf Club? - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo I recommend actually if you don't need to choke up rather if you could just go down a club.MoreSo I recommend actually if you don't need to choke up rather if you could just go down a club.
Should short golfers use shorter clubs?
Shorter golfers are often better served with shorter clubs, while the lie angle (how the club sits on the ground) may also need tweaking. If your clubs are too long and/or upright, you'll be forced to adjust away from a swing that's natural for you.
How long does it take to shorten a golf club?
Believe it or not, you can adjust them yourself, without going to a professional. These relatively easy steps will help you shorten a golf club in 45 minutes or less! Steps.
How to cut a golf club length?
1. Measure the desired new length of club. With the measuring tape, measure the desired length to be cut off. This distance should be taken from the top of the club. Mark the length. Use a permanent marker to mark where the cut should be made.
How to lubricate a golf grip?
Hold your finger to the tee-sized hole at the end of grip and spray the solvent into the other end. Shake this around to lubricate the inside of the grip. Put the grip onto the end of shaft. With your finger still holding all the solvent liquid inside the grip, slide the big hole onto the shaft.
How to install grip tape on a golf cart?
1. Apply grip tape to the end of the shaft. Put the new grip along the shaft to see how far down it will extend. This is how far you want the tape to go on each side.
How to get sticky glue off of a golf grip?
Spray with solvent. This will lubricate the tape so you can easily slide the grip over it. This solvent will dry up and become a sticky glue. Spray solvent into the grip. Hold your finger to the tee-sized hole at the end of grip and spray the solvent into the other end.
How to dispose of a golf club grip?
Prepare the work area. Place a towel or clothes underneath your vice grip. Place the club into the vice. Put the club into the vice such that the grip end of the club is pointing at you. Cut off the grip. With a utility knife, carefully make a cut along the grip. Remove the grip and dispose of it in the garbage.
How to smooth out a metal shaft?
Sand/dull the end of metal that was just cut. Take the sand paper and carefully smooth the end of the shaft. It will be sharp, and you do not want to rip the new grip that you will put on later.
What is backswing in golf?
Your backswing is done once your left shoulder passes the ball and your weight has loaded into your right thigh and right foot. That’s plenty of turn! Your arms should be extended, with the shaft short of parallel and pointing left of your target (viewed from behind).
How to find your backswing?
DRILL: HOW TO FIND YOUR PERFECT BACKSWING. Hold your driver with your right hand on the hosel and your left hand on the grip (above). With arms extended, turn as far as you comfortably can while maintaining your address posture and spine angle (below left), then stop.
Why is overswinging bad?
The problem with overswinging is that it can force a golfer out of his address posture, leading to an early release of the hands; this saps power and creates a poor impact position. So think “short” to go long. Here’s how.
Is it okay to swing past parallel?
Swinging past parallel at the top (above, left) is okay for the pros, but it can hurt the posture of weekend golfers—the hands release too soon (abo ve, right), robbing you of power. To shorten your backswing, load your weight into your right foot and thigh (above, left).
What does shortening the shaft do to a golf club?
Shortening the shaft can make the golf club less flexible.
How to cut a club in a vise?
Align your cut mark with the blade of the saw and secure the club in the vise. Put your safety goggles on and hold the club so it will not fall as you cut.
How much off will change the flex of the golf club?
Taking 2 inches off will change the flex of the club.
How many swingweight points do you lose when you remove 1/2 inch?
For every 1/2 inch you remove, you will lose approximately three swingweight points. You can readjust the swingweight by adding lead tape to the head of the club. Any amount of cutting will slightly stiffen the club. It will probably go unnoticed if you take 1 inch or less off the club.
How to measure golf clubs?
Measuring Your Clubs in Five Steps 1 Use a forty-eight-inch sturdy straight edge aluminum ruler. A tape measure is too flimsy and won’t give you an accurate measurement even if it is pressed against the club’s shaft. If you don’t currently own an aluminum yardstick, you can easily find one at a local home improvement store. 2 Don’t use your workbench to measure the golf clubs. A better alternative is to stand and place the club in its correct position at address. The sole of the club should be completely flat on the ground. 3 The straight edge should be placed so that the corner is touching the ground. The club should remain in address at this time with the ruler squaring up against the hosel. The hosel is the portion of the club where the clubhead is connected to the shaft. 4 The straight edge should be pressed as close as possible to the shaft. Now, read the measurement at the bottom of the grip cap. This should tell you the length of the shaft.
How many inches to a standard length golf club?
Six feet, five inches-add one and a half inches to the standard length of the club. Six feet, three inches to six feet, five inches-add one inch to the standard length of the club. Six feet to six feet, three inches-add half an inch to the standard length of the club.
How tall should a golf iron be?
Height Recommendations for Irons. Here you’ll find the standard recommended measurements for golf clubs based on height: Six feet, six inches and taller-add two inches to the standard length of the club. Six feet, five inches-add one and a half inches to the standard length of the club.
What is the most important spec to pay attention to when you’re shopping for a new set of golf clubs?
According to the pros, the length of golf clubs is the most crucial spec to pay attention to when you’re shopping for a new set of clubs or an extra driver or hybrid.
Why is dynamic fit measuring more reliable?
The dynamic fit measuring technique is more reliable because the measurement is taken as a player swings a club with the help of a launch monitor. A launch monitor is used to determine the correct head and shaft that will best suit the golfer’s playing style.
What should be taken into account when buying a new golf club?
When you’re getting fit for a new set of clubs, launch angle, dispersion, spin rate, and ball speed should also be taken into account in order to ensure you purchase the correct length.
How to tell the length of a golf shaft?
The straight edge should be pressed as close as possible to the shaft. Now, read the measurement at the bottom of the grip cap. This should tell you the length of the shaft.
How to shorten a golf club?
How to Shorten Golf Clubs. If you have purchased a set of used golf clubs that are too long, you can quickly cut them down to size with a hand-held rotary tool. You can also resize your old clubs and pass them on to your children. The shaft of a golf club is narrower at the head end to generate power on the swing.
How to keep golf club from moving?
Insert the golf club into a shaft clamp and tighten the clamp to keep the club from moving around while you work on the grip.
How to wrap a golf club grip?
Start at the end of the club and wrap grip tape around the shaft. Overlap the previous layer of tape slightly to keep it tight. Smooth out any wrinkles or bumps in the tape as you go along.
Why is the shaft narrower at the head end of a golf club?
The shaft of a golf club is narrower at the head end to generate power on the swing. When shortening a golf club, you must remove the grip and cut the wide end of the shaft so the club can still flex properly.
How to cut a club shaft with a rotary tool?
Insert the cutting blade attachment into the rotary tool according to the instructions in your owner's manual. Use the rotary tool to cut the club shaft along your marked line. Smooth out the end of the shaft with a piece of fine grain sandpaper.
How to dry golf grips?
Place the grip over the end of the shaft and push it down before the solvent dries. Inspect the fit of the grip and press out any uneven spots with your fingers. Allow the grip to dry overnight before using the club.
What Happens If Golf Clubs Are Too Short?
On that analysis, you should avoid using clubs that are the wrong size for you. But how can you tell if your clubs are too short?
How far can you aim with a shorter golf club?
When it comes to practicing your aim over 60 to 130 yards, shorter clubs can come in handy to help you dial in how hard to hit the ball and how to compensate your aim to hit each target. You’ll find you can work the ball a lot more with a lighter, smaller club, and the techniques you can develop with those types of clubs can then be put into practice with, let’s say, a 3-wood or a driver.
How Long Should Your Golf Clubs Be For Your Height?
The general rule is to ensure that when you address the ball, you have a little bit of bend in your knees, a slight tilt in your waist, and your hands should be able to hang loosely around the club, with the golf ball in the middle of the club’s face. But this varies for each club you use.
Why use the right length golf club?
That happens because you’re not trying to compensate as much for condensing your body to get closer to the ball as you would do with a short golf club.
What happens if you hit a golf shot with the wrong size club?
One of the first things you’ll notice when you hit a golf shot with the wrong-sized club is how much bend you have at the waist. Immediately you should know then that these are the wrong clubs for you. If you’re bending your knees or waist too much, that’s a sign you’re going to top or slice the ball.
How to tell if a golf club is too big?
If you stand completely straight over the shot and feel like the club is too flexible, and striking under the ball or hitting it fat are all signs the golf club is too big for you.
How to hit a golf shot?
When hitting a golf shot, you should be relaxed, with a bit of bend at your waist, softly bent knees, and your arms hanging loose around the club in front of you. That’s the type of posture you should be striving to achieve, and you can only get that by using a club that is the right size for you.
How to hit down on a golf ball?
To Hit Down on the Golf Ball: At setup, position the ball in the center of your stance. Shift your hands toward the target just slightly so the club is in front of the club head. In the transition, think about pulling on the club with your lead hand instead of throwing the club out and down with the trail hand.
Where should a short iron be placed in golf?
When using a short iron, make sure the ball is positioned in the center of your golf stance. In other words, it should be centered between your feet.
How does the club head change direction?
Think of the shape your club head makes as you swing through the golf ball. As you move through the transition at the top of your swing , towards the ball , the club head is traveling at a downward angle. At some point (more specifically, at the low point), your club head changes direction.
What irons are considered long irons?
First, make sure you know which irons are considered “long” and which are “short.”. Your long irons (2, 3 and 4) have a lower loft and are designed for more distance. (1 irons if you have them) Short irons (8, 9 and pitching wedge) have a higher loft and help you pop the ball up in the air as you get closer to the green.
What is the goal of an iron shot?
For an iron shot, however, the goal is to hit down on the golf ball. Another way to say this is that your moment of impact should occur before the low point of your golf swing. It’s important to make this distinction when discussing how to hit irons because this whole down/up thing trips up a lot of golfers.
How to avoid steepness when swinging a long iron?
However, you don’t want your angle of attack to be as steep as it is when you’re hitting a short iron. In order to avoid that steepness, position the ball just slightly forward of center.
Why do you swing away from the ball?
As you swing away from the ball, allow your head to slide away from the target. This accommodates for better rotation, better speed, and a better shot.
How to make your golf club a full length?
Many golfers strangle the grip, which keeps the face from turning over through impact and leads to a weak ball flight. Learn to let the toe rotate over the heel. Do it right and you’ll hit the ball a full club-length longer. Here’s how it’s done. Lay the handle diagonally across the base of your fingers, so that you don’t grip the club in your palm.
How to swing a golf club with your fingers?
SPEED UP THE TOE. Lay the handle diagonally across the base of your fingers, so that you don’t grip the club in your palm. This makes it easier to hinge and unhinge your wrists and rotate the clubhead more effortlessly. As you swing, you should feel the toe of the clubhead rotate past the heel, beating it to the ball.
Where should the shaft sit on a golf club?
The shaft should sit along the base of your fingers, not in your palm. If you have trouble making solid contact with your irons and frequently leave your approach shots short and right, your release may be the problem. Many golfers strangle the grip, which keeps the face from turning over through impact and leads to a weak ball flight.
How to swing a 7 iron?
Grab your 7-iron and swing the club halfway back (to 9:00). Let your wrists hinge naturally — don’t force it. At this point, check that the toe of the clubhead points at the sky. Now hit the ball and abbreviate your follow-through so that your hands finish at 3:00. Again, the toe should point skyward, which means that the clubface has rotated ...
What happens if the club is too upright?
Again if clubs are too upright, the heel is going to grab the turf before contact is made . Closing the clubface leading to slightly off center contact toward the toe, resulting in a fat pull. shot pattern. If the toe if the club is moving faster than the heel your going to make contact. more on the toe side of the face.
What happens if the ball is not leaving well before the clubhead hits the ground?
And if the ball is not leaving well before the clubhead ever hits the ground, you're hitting it fat. Lie, nor length, doesn't affect that.
What is the difference between center hit and toe hit on irons?
The difference between center and toe hits on most irons is on the order of millimeters. You just need some range time to dial in the feel of centered impact on the new set, unless the specs are quite different from the old set, in which it might take quite a few balls and rounds to get the new set comfortable. Quote.
Is a club too short?
Conventional fitting wisdom suggests that if you're consitently striking the ball towards the toe, the clubs could be too short, if your impact marks are inconsitent / all over the shop, they're probably too long. I have some literature on this (quite good stuff from the titleist fitting manual) somewhere, but I can't find it right now.
Can you swing a golf club if your toe isn't moving?
If the toe [i]isn't i] moving faster than the heel, you're not swinging a &] golf club. The length of arc that the heel travels on through impact is shorter than the arc the toe travels on, so for them to remain attached to the same clubhead, the toe has to move faster. Remember, the club doesn't travel in a dead straight line, it's a (nearly) circular path about the golfer.
Is it too short to strike the ball towards the toe?
Conventional fitting wisdom suggests that if you're consitently striking the ball towards the toe, the clubs could be too short, if your impact marks are inconsitent / all over the shop, they're probably too long . I have some literature on this (quite good stuff from the titleist fitting manual) somewhere, but I can't find it right now.
