- First, remove club head from shaft. If head is not removed the intense heat will cause the ferrule to melt and the epoxy to breakdown and a reshaft ...
- Next, you will need to soak the club head using the 1 Liter Coke bottle for about an hour. This will strip any existing finish on the head. ...
- Now remove your club from the Coke. ...
Can You recondition wedges with a hand-held groove tool?
First, let me say that using a hand-held groove tool is a risky way to recondition the grooves in your wedges. The reason is that as soon as you alter (recondition) the face of the club it is considered new and ruled on accordingly.
What are the best tips for refinishing golf clubs?
When refinishing golf clubs, it is best to collect everything you will need--from new shafts or grips to double-sided tape and solvent--before you start. Refinishing or club-making kits are available at most major retailers.
How much does it cost to replace a wedge?
If you would just like to make a change – wedges don’t change very much in style or shape --you can buy a new one which will cost about $110. If you do decide to buy a new wedge make sure it has the same specs, i.e. bounce, loft and lie as the good friend you are about to give up.
How do you thank someone for restoring a wedge?
Thank you so much for your help in restoring these to my requested look and specs! I have a couple of other wedges that I’m hoping to have restored, and I’ll definitely send them your way! ” “ Received my 55 degree wedge, which you totally rebuilt today.
How do you restore a wedge worn?
0:006:59Golf Wedge Restoration - YouTubeYouTubeStart of suggested clipEnd of suggested clipStep one is to pull the head. Two main methods for pulling. Ahead heat gun torch and typically you'MoreStep one is to pull the head. Two main methods for pulling. Ahead heat gun torch and typically you're going to use a shaft puller but for all of you at home who don't actually have a shaft puller.
How do you restore a rusty golf wedge?
Similar to Coca-Cola, the acidity of Vinegar and Lemon Juice works to break down and remove rust. A quick soak can easily loosen surface rust and allow your club to be cleaned using a brush.
Can I paint my wedges?
5:126:56The Shop: How to stamp and paint fill wedges - YouTubeYouTubeStart of suggested clipEnd of suggested clipReally doesn't take that long with nail polish you can use enamel paints and those were great thereMoreReally doesn't take that long with nail polish you can use enamel paints and those were great there probably are a little more durable.
How do you refurbish a golf iron face?
0:004:48DIY Golf Club Restoration - Reconditioning the Club Face TutorialYouTubeStart of suggested clipEnd of suggested clipSo i'll throw some masking tape on i also have a little bit of aluminum tape which is a little moreMoreSo i'll throw some masking tape on i also have a little bit of aluminum tape which is a little more durable than just masking tape i'll probably put that just on the edges.
Why do Vokey wedges rust?
The Jet Black will rust as the dark finish wears, while the Raw wedges will rust more quickly with exposure to air and moisture.
Are rusty wedges good?
TaylorMade says, and it has been a commonly held theory for a while, that raw wedges that go rusty will spin more and feel softer over time. They should also reduce sun glare and preserve the geometry of the grooves for longer-lasting spin.
What kind of paint do they use on golf clubs?
Enamel paint and preferably epoxy-based enamel paint is highly recommended. Enamel is oil-based, adheres easily to metal surfaces, is highly durable, and, has a gloss finish. Acrylic Paint. This paint is water-based and drys quite quickly and is cheaper than enamel paint.
How do you customize a wedge?
0:467:03The GolfWRX Shop: How to stamp a wedge - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo just take a couple pieces of two-sided. Tape. Put it right on top of the middle of the anvil.MoreSo just take a couple pieces of two-sided. Tape. Put it right on top of the middle of the anvil. Hold that wedge in place. Set the wedge. Down.
Can you spray paint a golf club?
You Can Now Use the Paint for Repainting Your Golf Club Shafts. Once the primer has dried, you can easily use an acrylic oil-based paint or any epoxy-based paint to repaint your golf club steel shaft. You can pick any color paint of your choice and apply thin coats of this paint on top of your shaft.
How do I make my golf clubs look new again?
Mixing up warm water and mild soap. Fill the bucket with a not-so-hot water. ... Submerge the club several times for 5 to 10 minutes. If your club is not that messy, you can submerge the golf club heads for just 5 minutes. ... Remove and scrub the clubheads. ... Apply steel of chrome polish.
Can you use metal polish on golf clubs?
Apply any metal polish or car wheel polish to the golf clubs. Most polishes can be applied with a soft cloth or towel. Let them sit for a minute, then wipe the polish from the clubs. Spray polishes are also available.
How do I re Chrome my irons?
1:2412:33How to restore the chrome finish on a set of golf club irons - YouTubeYouTubeStart of suggested clipEnd of suggested clipAfter they've been wired up on copper wires or hooks in this case then we put them in a tank ofMoreAfter they've been wired up on copper wires or hooks in this case then we put them in a tank of sulfuric acid and some other things. And we reverse the process and we're actually plating the plant.
How long does it take to get a torch finish?
This will take some time to get the torch finish you are looking for. You will generally not begin to see any changes for at least 4-5 minutes. Patience is the key with this type of finish.
How to soak a golf club head?
STEP 2: Next, you will need to soak the club head using the 1 Liter Coke bottle for about an hour.
Can you heat oil in an oven?
You can also use an oven to do the heating process. ( WARNING: if quenching in oil during the cool down process make sure to do outside, there is always a risk when dipping a hot head into oil. You should make sure the head is not that hot when dipping in oil.)
Can you dip a hot head in oil?
(WARNING: if quenching in oil during the cool down process make sure to do outside, there is always a risk when dipping a hot head into oil. You should make sure the head has cooled down considerably when dipping in oil.)
Your new favorite hobby–golf club refinishing
There is nothing more satisfying than turning an old, beat up putter into a masterpiece. In this refinishing series, I’ll show you the techniques required to unleash your creativity on all your old golf clubs!
Brass vs. Carbon Steel vs. Stainless Steel
When I first started refinishing golf clubs, I had a difficult time finding information. One of the topics that caused me a lot of unecessary struggle was not knowing the different types of metal that golf clubs are made of.
Preventing Rusty Golf Clubs
For some finishes, it is difficult, if not impossible to prevent rust on a golf club. In this post I’ll show you my preferred method for preventing rust on golf clubs.
Refinish a Scotty Cameron Headcover
If you have an old Scotty Cameron Newport Select putter headcover laying around, you can turn it into a custom beauty!
Paint Fill 101
The quickest and easiest way to customize your golf clubs is by painting the text on them. I’ll show you some of my favorite techniques for doing so, my preferred paints, and some quick tips that will make your life a lot easier when customizing your golf clubs.
Removing Nicks and Dings on a Golf Club
Ever wonder how a golf club is refurbished? Did you know that your beat up putter in the basement can be completely transformed in just a few minutes? It’s called a “deburring wheel”, and it will be your single biggest tool in golf club refinishing.
Make a Scotty Cameron look Brand New (Basic Satin Finish)
The great thing about stainless steel putters (most new Scotty Camerons) is the fact that after refinishing them, they don’t rust! Here is the most basic finish you can do on a stainless steel putter, and it looks clean and awesome.
Feedback
I think you should share this kind of info in the open part of the forum when someone is asking, so here is my way of doing it.
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
