The ignition switch in an E-Z-GO golf cart is what enables the vehicle to start when you turn the key. If you're having a problem getting your golf cart to start, it's possible you have a bad ignition. Fortunately, it is very easy to install and replace the switch.
Full Answer
What does the ignition switch do on an EZ GO golf cart?
The ignition switch in an E-Z-GO golf cart is what enables the vehicle to start when you turn the key. If you're having a problem getting your golf cart to start, it's possible you have a bad ignition. Fortunately, it is very easy to install and replace the switch. It is both inexpensive and quick (around ten minutes).
Where is the ignition wire on a golf cart starter?
Locate the ignition wire on your golf cart. This wire goes from the golf cart key switch assembly to your cart's starter. Visually inspect the solenoid area of the starter, where the key switch wire plugs into the cart. On some cart models, this end of the key switch wire can become dislodged during use on rough terrain.
How to fix a golf cart key switch that won’t start?
Replace the golf cart key switch after replacing the key switch ignition wire as a last step. This will ensure that you replace the higher-priced part last while troubleshooting your golf cart key switch. After replacing the switch, your cart will start.
How to start a golf cart with a screwdriver key?
You’ll have to wiggle your screwdriver up and down, keeping just a little tension on the switch. This will eventually loosen up the tumblers and allow you to turn your screwdriver key, flip the ignition switch, and start your golf cart.
What is the toggle switch on a golf cart?
This toggle switch is used to "kill" the car for towing, maintenance, and long-term storage.
How do you operate a toggle switch?
1:182:10"On-Off" (single pole) Toggle Switch for automtive use with Wiring ProductsYouTubeStart of suggested clipEnd of suggested clipThe way that we did it today red goes on red black goes on black give it power and turn it on andMoreThe way that we did it today red goes on red black goes on black give it power and turn it on and there you go that is how you wire up an on/off toggle switch thank you for visiting wiring products.
What does a micro switch do on a golf cart?
Microswitches are used in many golf cart applications. They are used at the accelerator pedal to provide a signal to the solenoid that you have depressed the pedal and are ready to go. In an electric golf cart, the solenoid sends power to the controller to move the cart.
What does ezgo micro switch do?
A micro switch on the accelerator pedal gets activated once the pedal is pushed. This sends a signal to the solenoid and in turn more power to your wheels to make them move faster. These micro switches are more common in electric golf carts.
What is a toggle switch?
A toggle switch is a type of electrical switch that is actuated by moving a lever back and forth to open or close an electrical circuit. There are two basic types: maintained contact and momentary toggle switches.
What does toggle mean?
Definition of toggle (Entry 2 of 2) transitive verb. 1 : to fasten with or as if with a toggle. 2 : to furnish with a toggle. 3 : to switch between two different options for (something, such as a computer setting) usually by pressing a single button or a simple key combination toggle the sound on a computer off and on.
Where is the micro switch located on a golf cart?
In a golf cart, you're going to find a large number of these switches throughout its build. For example, there is a micro switch located on the accelerator pedal. This switch activates when you push the pedal and sends a signal to the solenoid.
How do you bypass a micro switch?
2:273:45How to create a jumper wire and bypass a safety switch in your Pellet ...YouTubeStart of suggested clipEnd of suggested clipSo I'm just going to use my jumper wire. And we're just going to plug in each end of the leads thatMoreSo I'm just going to use my jumper wire. And we're just going to plug in each end of the leads that went to the vacuum. Switch. Just like that. So now I have successfully bypassed my vacuum switch.
How do you test a micro switch on a gas golf cart?
Again, leave your black probe on the battery negative terminal and use your red probe for testing. With the key switch ON, you should read battery voltage at the common terminal (C or COM), but not the other terminal. Once the micro switch is activated, you should read voltage on both terminals.
What does a micro switch look like?
0:224:00Understanding a Microswitch - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's better known as a snap action switch. Because it uses a spring to open and close connectionsMoreIt's better known as a snap action switch. Because it uses a spring to open and close connections inside of it if you move the lever on a good switch you can hear the spring snap back and forth.
How do you hook up a micro switch?
1:115:14How to Wire up a Micro Switch - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe negative of the power source should then go to the other end of the component. To turn somethingMoreThe negative of the power source should then go to the other end of the component. To turn something off when the switch is pressed the power source wire should go to the normally closed.
What is micro limit switch?
The micro limit switch, or micro switch, is another type of limit switch commonly found on control circuits. These switches are much smaller than their standard counterparts, allowing them to be installed in narrow or cramped spaces that would normally be inaccessible to other switches.
How do I know if my toggle switch is on or off?
As an eyelid opens, the eye can see, meaning the switch is on. When the eyelid closes, we can't see, meaning the switch is off. This metaphor works for electric switches, light switches and (modern) fuses.
How does a 2 way toggle switch work?
They typically have two terminals. One is for input, the other for output. In one position the switch is 'Open' and no connection is made, and no power can flow to the accessory. In the other position the two terminals are connected and power can flow through.
How does a single pole toggle switch work?
4:185:33Electrical Switches, Part 2, Toggle Switches - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis life switch is a single pole single throw spst switch it has only two connection terminals itMoreThis life switch is a single pole single throw spst switch it has only two connection terminals it suitable for controlling lights that have only one switch.
How do I turn off my toggle switch?
To disable a toggle switch, add the disabled attribute to the toggle's checkbox input. When disabled, the toggle appears gray. The user cannot change the state of the toggle.
Why replace the key wire on a golf cart?
Replace the golf cart key switch wire if the connector to the key switch or solenoid is significantly frayed or corroded. Over time, corrosion will build up on the ends of the wire due to exposure to damp weather. Significant corrosion build-up can prevent your cart from starting consistently and ultimately result in the cart failing to start.
What direction does a golf cart transmission selector go?
Confirm that your golf cart transmission selector switch is set fully to the forward, reverse or park direction , depending on your model of golf cart. If the switch is partially set in between modes, it can result in your cart failing to start correctly.
How many wires should an ignition switch have?
Also, the ignition switch should only have the two wires going to it anyway. If there are three, then don’t use the black one. If there are more than three, then a wiring diagram may help, but trial and error will eventually find the right pair.
Can you use a friend's key on a golf cart?
Use a friend’s key. Maybe your friend is with you and they have a golf cart from the same brand. Whether it’s E-Z-GO, Yamaha, or Club Car golf carts, as long as the brand is the same, the key is usually the same, too. Hopefully, you can just use their golf cart key and not have to worry about it. This is also a fun way to pull a prank, ...
Can you trick a golf cart into starting?
It will eventually become inconvenient having to figure a way to trick your golf cart into starting. Of course, if you’re already going to have to wait for a key, you might as well order a new, key specific ignition switch to make your golf cart more secure.
Can you hot wire a golf cart?
Whether you do this by simply replacing the key, installing a new ignition switch, or any other method, it’s essential that you only hot wire your golf cart for only as long as absolutely necessary, since it causes undue stress on the wires and battery. This can void your warranty and cause other issues down the line.
Is it easier to start a golf cart than a car?
Fortunately, golf carts are a lot easier to start than a traditional car. Whether you have an E-Z-GO, Yamaha, Club Car, or any other type of golf cart, the process is very similar, and this article will walk you through it. The issue with having the right key can come up, especially if you bought a used golf cart and didn’t get a second set of keys.
Can you start a golf cart without a key?
So, you need to start your golf cart without a key. There are two ways to accomplish this, one is really easy, but only works sometimes, and the other is a little complicated, but will work every time without fail if you do it right. Generally speaking, you’re gonna want to start with the first method, and only approach the second if ...
Is an ignition switch a circuit?
Your ignition is a circuit, and the ignition switch is kind of like a light switch that closes that circuit, allowing ignition to take place. By jumping, or bypassing, that switch you’re making an always closed (or hot, hence hot-wired) circuit.
What is a golf cart go switch?
On your golf cart, this high powered circuit is either your ignition on a gas golf cart or your electrical motor power circuit for an electric golf cart. Basically it’s your golf cart’s go switch, and it’s absolutely essential to your golf cart’s ability to do its job. Golf cart solenoids are also typically one of the first components ...
What is a solenoid on a golf cart?
A solenoid, for our purposes, is a type of relay. A relay is a type of switch that uses a low power circuit to operate a high power circuit. A solenoid uses a magnetic coil (the actual solenoid) on a low power circuit to push a rod that closes a high power circuit. On your golf cart, this high powered circuit is either your ignition on ...
Why does my golf cart have no solenoid?
Golf cart solenoids are also typically one of the first components to fail in your golf cart, because they work very hard, turning on and off every time you stop and go in your golf cart. If you have an issue with no start or no go then your solenoid should be pretty high on your list of things to check.
What happens if a solenoid reads infinity?
If it reads infinity or open lead, then the solenoid has an internal fault and requires replacement. Your solenoid should also have a range that it operates in, and if the resistance reads outside of that range, you should replace the solenoid even if it works to avoid damaging other components.
What is the most important part of a golf cart?
One of the most important components of your golf cart is the solenoid. It is one of the main components of your golf cart that allows it to move. Whether you have a Yamaha, E-Z-GO, or Club Car golf cart, and no matter if it is an electric or gas golf cart, you need a properly operating solenoid to get anywhere. Contents [ show]
What to do if your solenoid doesn't work?
Before you run out and get a solenoid, you’ll have to test the entire ignition system this way to find out what’s not working, and it is a bit of a pain.
What is a micro switch on a gas pedal?
This switch is what sends the low power to the solenoid. The solenoid uses this to create a circuit between the battery and the starter, thus starting your motor and getting you grooving.
How long does it take to replace a golf cart ignition switch?
Fortunately, it is very easy to install and replace the switch. It is both inexpensive and quick (around ten minutes ). There are just four steps: Get the right equipment, prepare the golf cart, remove the console and the existing ignition switch, and lastly, install a new ignition switch and replace console.
What is the face nut on a car ignition?
The face nut is the round piece that holds the ignition switch in place. Once the face nut is removed, the ignition switch will detach. Hang onto the lock nut for the new ignition switch if a new lock nut is no available. Remove existing ignition switch from plate.