With irons, you have to admit that these are highly versatile golf clubs because they feature varying lengths based on the type or number of iron. So you have 1 to 9 irons, which means different shaft lengths. Typically, this range is between 34 inches and 40 inches (depending on the brand).
Full Answer
How many shafts are in a golf iron?
With irons, you have to admit that these are highly versatile golf clubs because they feature varying lengths based on the type or number of iron. So you have 1 to 9 irons, which means different shaft lengths. Typically, this range is between 34 inches and 40 inches (depending on the brand).
What determines the length of the golf irons?
The height of the player is one of the primary factors that determine the length of the golf irons. There is no average length that can be considered to be suitable for a large number of players.
Do numbers lie in the comparison of iron shafts?
But in our big comparison of iron shafts, we would like to be. After all, numbers do not lie. Therefore we will sort our shafts into different CPM categories. The CPM value itself need not be of interest to you - it depends on how you measure it exactly.
What was the first single length set of golf irons?
Probably the first true, mass-produced single-length set was the Tommy Armour EQL irons set released in 1988. All the irons were the length of today's traditional 7-irons; the EQL woods were all the length of a traditional 5-wood.
What is the standard shaft length for an iron?
With steel shafts, the standard length of a 5 iron golf club is 37.5 inches. With a graphite shaft, the standard length for men is 38 inches and for women, it stands at 37.25 inches. A 5 iron golf club usually offers a 28-degree loft angle.
How do you determine club shaft length?
The following lists what length of shafts you should consider for certain heights. If the crease where your wrist and hand meet to the floor is: 29 to 32 inches = irons should be based on a 5-iron of 37 inches. 33 to 34 inches = irons should be based on a 5-iron of 37 1/2 inches.
What does the number on a club shaft mean?
These numbers are the weight of the shaft in grams. Shaft weights typically range between 50 grams and 85 grams with the 50-60 numbers being pretty common as seen in the example shafts above.
How are iron shaft lengths measured?
A 48” golf club ruler is placed along the backside of the club with the tip of the rule touching the ground by the club's heel. The final length is measured at the edge of the grip cap (and not the very top). This method is used in all cases except putters that the shaft is not located at the heel.
How long is a 7 iron shaft?
Iron Shaft LengthIRONSHAFT LENGTH for Men (steel/graphite)SHAFT LENGTH for Women (steel/graphite)6-iron37.5/38 inches36.5/37 inches7-iron37/37.5 inches36/36.5 inches8-iron36.5/37 inches35.5/36 inches9-iron36/36.5 inches35/35.5 inches4 more rows
What is the length of a standard 5 iron?
Standard Club LengthClubMen GraphitLady SteelWood 7#, 9# usw.4139,5Iron 3#39,538Iron 4#3937,5Iron 5#38,53728 more rows
What does 6.0 mean on a golf shaft?
StiffRegular – 5.0. Regular Plus – 5.5. Stiff – 6.0. Extra Stiff – 6.5. Extra Stiff Plus – 7.0.
What does the number on an iron mean?
0:053:33Golf Basics : What Do the Numbers on Golf Clubs Mean? - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the the basically the way to remember it is we'll start with a 9-iron because those are the onesMoreSo the the basically the way to remember it is we'll start with a 9-iron because those are the ones that are actually numbered start with a nine a 9-iron means that the golf club is very lofted.
What do the numbers represent on the golf clubs?
Golf club numbers refer to the loft, which is the angle of the golf club face. When you adjust the loft, you are changing the height and distance the golf ball will travel when struck.
How long should my irons be for my height?
Using the ratio of every 6" of height there should be a 1" change in length then there should be a 1 ½" difference between their 5-irons. For example, recommend 36.5" for the lady and 38" for the man (or 36.75" / 38.25").
How is driveshaft length measured?
How to Measure a Driveshaft with a Slip Yoke and U-jointPlace one end of the tape measure near the middle of the front u-joint.Place the other end of the tape measure near the middle of the rear u-joint.Note the measurement on the tape measure to determine the length of the driveshaft (without the slip yoke).
What is the standard length of a 4 iron?
Standard Length for Irons This standard measurement increases 1/2 inch for each consecutive number iron. For example, standard length for a steel 2 iron is 39 inches; a 3 iron is 38.5 inches; a 4 iron is 38 inches and so on to the steel 9 iron with the standard length of 35.5 inches.
How many degrees of loft does a golfer have?
The average male golfer still hits a club with 24 degrees of loft and an overall length of 38 inches, 170 yards. What has changed is that the number assigned to the club has changed from a ‘3’ to a ‘5’.
Can you use a 7 iron as a 6 iron?
When you take a 7 iron and substantially decrease the loft and extend the shaft by up to an inch you have effectively turned it into a 6 iron and yes , 6 irons will go further than 7 irons. Between 1970 and the present most if not all club manufactures have strengthen the lofts, and extended the shafts on off the counter iron sets, ...
How long should a golf iron be?
For most golfers, the length of a golf iron should be 38.75 inches. The height of the player is one of the primary factors that determine the length of the golf irons. There is no average length that can be considered to be suitable for a large number of players. A player who is 6 feet and 3 inches tall will often not be very comfortable using ...
What is the standard length of a 9 iron golf club?
With graphite shaft, the standard length for men is 34.35 inches and for women, it is 33.75 inches. A 9 iron club is categorized as a short iron golf club. The 9 iron features a high-mass clubhead and a short shaft.
Why do golf clubs have long shafts?
Golfers often use long shafts in their golf clubs as they feel that the club with a longer shaft would help it to cover a large distance. This is not exactly true but lengthening golf irons does have a direct impact on your game and performance. There are different ways in which you can lengthen your golf iron.
Why use single length irons?
Here are a few reasons why some golfers may prefer using single length irons: 1 It’s easy to hit by having a shorter shaft on low-loft irons 2 You can have the same swing on all the shots 3 The player doesn’t have to reposition the ball or change anything between two shots
How long is a 5 iron golf club?
With steel shafts, the standard length of a 5 iron golf club is 37.5 inches. With a graphite shaft, the standard length for men is 38 inches and for women, it stands at 37.25 inches. A 5 iron golf club usually offers a 28-degree loft angle. The 5 Iron is a mid-range golf club featuring an iron clubhead.
Why shorten your iron?
Shortening the length of a golf iron helps to hit shots at the center of the clubhead consistently. A lot of players feel that their shots are more accurate once they shorten their irons.
What is a 5 iron?
The 5 Iron is a mid-range golf club featuring an iron clubhead. This is largely used from the rough and the fairway. It’s also appropriate to use the club in slightly higher surfaces or hilly areas. It helps the player in avoiding the possibility of hitting a low rise shot.
How long does it take to find the perfect shaft profile?
It is difficult to give basic recommendations and the perfect shaft profile can only be found in a fitting and usually over longer playing periods. It can take years for a player to find the perfect profile. Therefore a player usually stays with it and remains consistent throughout the set.
How fast can a 6 iron hit?
This category includes above average amateurs who hit their 6 iron between 155 and 170m and have a club head speed between 80 and 90mph. Please note that these are only approximate values.
What is the softest point of a shaft?
Then there are shafts with a stiff tip and a soft grip area. Basically the tip is the softest point of the shaft. These shafts are nevertheless stiffer at this point than, for example, in the middle of the shaft.
What is graphite shaft?
Theoretically, they can combine the best of both worlds. A graphite shaft is basically lighter and able to dampen vibrations better. Shaft weight: The weight of a shaft influences both the total weight and the swing weight of the club.
What does the stiffness of a shaft mean?
The stiffness indicates the stiffness of the entire shaft, but not whether the shaft is stiff in the tip, middle or butt section.
Is a carbon shaft flexible?
A carbon shaft therefore does not mean being flexible at the same time. You can find the respective shaft weight in the charts above. It is important to know that a number like 80 always represents a "lower limit" and the actual weight is always slightly above this number, e.g. 83g.
Is a carbon shaft stiffer than steel?
Basically, carbon shafts tend to be lighter than steel, but can be built just as stiff - sometimes even stiffer. A carbon shaft therefore does not mean being flexible at the same time.
How many clubs are in a set of irons?
A typical, off-the-shelf set of irons will include a 3-iron through pitching wedge (advertised as "3-PW"), 8 clubs total. The clubs are identified by a number (3, 4, 5, etc.) on the sole of each club, except for the pitching wedge which will have a "PW" or "P." Other irons may be available for purchase separately, including a 2-iron and additional wedges ( gap wedge, sand wedge, lob wedge). None of the additional clubs are necessary for beginners, and especially not the 2-iron. 1-irons used to be available, too, but are now virtually extinct.
Why are golf clubs called irons?
The golf clubs called irons are so-called because their clubheads are made of metal. Of course, "woods" are now also made of metal, but that's a relatively recent development. Irons have featured metal clubheads (steel, these days) for centuries. The clubheads of irons are thin from front to back, and the clubfaces are grooved to impart spin on ...
Why are irons called irons?
The golf clubs called irons are so-called because their clubheads are made of metal.
What is the difference between a blade and a muscleback iron?
The difference is that a blade-style features a full back on the rear ...
How many yards is a 3-iron?
The yardage gap between irons is generally 10-15 yards. Your 3-iron, in other words, should produce shots that are 10-15 yards longer than your 4-iron. The specifics of this gap depend on the player, but the gap should be consistent from club to club.
What are the different types of irons?
Irons are generally categorized as long irons, mid-irons , and short irons. Long irons are the 2-, 3- ,and 4-irons; mid-irons, the 5-, 6-, and 7-irons; short irons, the 8- and 9-irons and pitching wedge. (Two-irons are becoming obsolete and are exceedingly rare for recreational golfers. Because of this, some sources now count the 5-iron as one ...
Why is a shorter shaft better?
A shorter shaft makes a club easier to control in the swing (think of baseball where a batter will " choke up " on the bat—essentially, shorten the bat—when he's simply trying to make contact rather than swing for the fences). More loft helps get the ball airborne and adds a little more control to the shot.
Why is it important to choose the right golf shaft?
Choosing the proper shaft is a hugely important part of the fitting process. The shaft will greatly influence the feel of your irons, not to mention the launch, spin, landing angle, and distance of your golf shots. Also, there are no standards in ...
What is the lie angle on iron fittings?
Lie angle is one of the most important specs to get right in an iron fitting. If it’s off, you’ll have a much harder time with accuracy and hitting more greens. Historically, lie angle has been measured by reading divot patterns or using sole tape and a lie board to mark strike point being centered, toe, or heel down.
Do upright clubs go left or right?
Upright clubs tend to go more left…. Bending them upright might give a cleaner divot but would make his misses even further to the left. Not a good move as a fitter. Incidentally, when the face is closed, the toe is lower, the lie board was giving him a false impression of his club’s lie angle at impact.
What is a 5-iron set?
In a traditional iron set - what some have started referring to as "variable-length irons" - each iron in the set is a different length. The irons get shorter as the number gets higher. A 5-iron is shorter than a 4-iron; a 6-iron is shorter than a 5-iron; and so on.
When were single length irons invented?
The idea for single-length irons goes back at least to the 1930s, probably much earlier. An antecedent can be found in a set of irons Bobby Jones designed for Spalding, in which every two clubs were the same length (3- and 4-iron were the same length, 5- and 6-iron, and so on). Probably the first true, mass-produced single-length set was ...
What is the difference between lie angles and clubheads?
The clubheads are all identical weights; the lie angles are all identical and about 10-degrees more upright than typical . The point, DeChambeau says, is to "create a swing that's consistent from club to club, that doesn't have a lot of moving parts to mess up.". And it works for him.
When did DeChambeau start making his own irons?
When he was 17 years old, under the influence of his instructor at that time plus the instructional book The Golfing Machine (by Homer Kelley, published originally in 1979 ), DeChambeau fashioned his own set of single-length irons (they were all the length of a traditional 6-iron).
Who is the only golfer to win the NCAA Championship?
And it works for him. In 2015, DeChambeau joined Jack Nicklaus, Phil Mickelson, Tiger Woods, and Ryan Moore as the only golfers to win the NCAA Championship and U.S. Amateur Championship in the same year. In 2016, DeChambeau won his first pro tournament, the Web.com Tour 's DAP Championship. And in 2017, DeChambeau became ...
Is single length iron new?
Single-Length Irons Are Not New. There are new technologies in golf all the time, but there aren't a lot of new ideas. So it's not unusual for old ideas to get recycled, expanded upon, tweaked, improved on, especially once the technology catches up to the idea. The idea for single-length irons goes back at least to the 1930s, probably much earlier.
Do you have to move the golf ball forward or back?
No need to move the golf ball forward or back in your stance depending on the club used; no resetting to adjust to a club's length; no swinging more or less upright, no more one-plane or two-plane to adjust to club length. This is the major selling point and should benefit golfers of all skill levels.
What does short bottom bore to ground mean?
Posted April 11, 2020. A short bottom bore to ground means more shaft is in play, which means the shaft will play a smig softer. One more reason to NOT soft step. Most of Titleist's club lineup consists of players clubs, many of which come stock with True Temper Dynamic shafts.
Is a 95 shaft better than a 105?
The 95 is a little softer than the 105 so to keep the same flex as your 105's that means you should hard step 1X compared to your 105 shafts. In other words, if the 105 shaft in your 4 iron is a 38.5 now, use a 38.0 95 shaft in it when you rebuild (which happens to be the Nippon suggested build standard.)
rbilramz
I am a fairly tall guy (6’-4”), and after being fit a few years ago I play irons at +1/2” and 2 degrees upright. However, I play my driver at 45” and my 3-wood at standard length.
Pepperturbo
My thought is to order your driving iron 1/2" over. Lie angle is a variable per person, so get it adjusted when you get it. The only issue that can come from 1/2" over in length is possibly an increase in SW that you may or may not notice.
Popular Now
You're not a touring pro but you bought a launch monitor anyway. Well.....?
Set Composition
Loft, Length, and Distance
- As you go through the set, from the 3-iron to the pitching wedge, each iron has a little more loft than the previous, and a little shorter shaft length than the previous, so each club (going from 3-iron to PW) hits the golf ball a little less distance than the previous. That is, a 5-iron has more loft, a shorter shaft, and produces shorter shots th...
Long, Mid-, and Short Irons
- Irons are generally categorized as long irons, mid-irons , and short irons. Long irons are the 2-, 3- ,and 4-irons; mid-irons, the 5-, 6-, and 7-irons; short irons, the 8- and 9-irons and pitching wedge. (Two-irons are becoming obsolete and are exceedingly rare for recreational golfers. Because of this, some sources now count the 5-iron as one of the long irons. We still classify it as a mid-iron…
Distances
- Learning your distances—how far you hit each club—is much more important than trying to hit each club to some predetermined "correct" yardage. There is no "right" distance for each club, there is only your distance. That said, a typical male recreational golfer might hit a 4-, 5-, or 6- iron from 150 yards, while a typical female might use a 3-wood, 5-wood, or 3-iron from that distance. …
Hitting
- Irons can be played from the teeing ground, using a golf tee, and it is often appropriate to do so. On a par-3 hole, for example, you will probably use an iron on your tee shot. Or you might use an iron off any (or even every) tee in order to have better control over the shot. But most of your iron shots will come from the fairway. Irons are designed with divots in mind. That's why they have a …