
What is the butt end on a golf shaft?
On the opposite side of the shaft is the butt end. This is the side where the golf grip will be installed. The butt diameter is measured about 2" down from the top of the shaft. For standard size shafts for adult players, this will usually be around 0.600", (or larger if it's a bubble shaft).
What is a golf shaft?
Either way, the golf shaft is where power is stored and released at impact. Sitting in between the golf grip and club head, a solid connection is what allows the golf shaft to do its job. So when choosing a shaft, it's important to know what specifications to look for.
What is butt diameter of a shaft?
Butt Diameter (Butt OD): The outside diameter of the butt end of a shaft. The range is generally .580″ to .640″. Larger butt diameter shafts are found in stiffer and heavier shafts.
What are the butt stiffness codes on a shaft?
There are several other alphanumeric codes used to designated the butt stiffness of a shaft. OBAN uses numeric codes: 2=Senior Men’s, 3=Regular Men’s, 4=Stiff Men’s and 5=Extra Stiff Men’s.

What is the butt of the shaft?
BUTT: The top end of the shaft, called the butt, is located underneath the grip. Shafts have different amounts of torque and flex in the butt, just as they do in other sections of the shaft.
How do I measure my butt for a golf shaft?
If you're not sure what the hosel ID is, you can measure it with a fine tip gauge or contact the club manufacturer for this information. On the opposite side of the shaft is the butt end. This is the side where the golf grip will be installed. The butt diameter is measured about 2" down from the top of the shaft.
What does butt frequency mean?
Refers to the resonant frequency of a shaft when the butt (handle) end is anchored and the tip is made to vibrate. Usually, the shaft is anchored at the butt end when performing a resonant frequency test.
What flex should my shaft be?
– Golf Shaft Flex ChartCarry DistanceSwing SpeedFlexUnder 200 yardsUnder 75 mphLadies or Senior200 to 240 yards75 to 95 mphRegular240 to 275 yards95 to 110 mphStiffOver 275 yardsOver 110 mphStiff or Extra StiffOct 15, 2019
What is butt flex?
Flex: This is the stiffness of the shaft as measured in the first 15-20 inches of the butt section of the shaft. There are a variety of stiffness indicators that manufacturers use to designate the stiffness of their shafts.
Who should use midsize golf grips?
As a general rule, if you wear a golf glove size of Large / Cadet Large or bigger, a Midsize or Jumbo grip is the proper fit for you. If you're not sure whether you would benefit from a larger grip, take one of your current golf grips in your top (lead) hand.
Is a 6.0 shaft Stiff?
5.0 out of 5 stars 6.0 62g is VERY stiff! Great shaft! The only thing I would say to someone who is looking at this is if you normally play a stiff shaft you should go with the 5.5 62g variant. the 6.0 62g shaft is extra stiff in my opinion.
What weight golf shaft should I use?
In general, golfers with slower swing speed and tempo can and should play a lighter shaft. Golfers with very fast speeds and tempo should play heavier shafts. Driver shafts typically weigh 55-60 grams for men and 45-50 grams for ladies.
What is tip flex of a golf shaft?
Tip Flex: Tip Flex, or Retro Flex, represents the average stiffness toward the head side of the shaft. Sometimes this is measured in a very similar fashion as the static-flex measurement. The difference being that the tip end is clamped and the load is applied to the butt end of the shaft.
What flex should a beginner use?
But if a beginner player already has a decent swing motion and generates clubhead speed between the range of 95 to 110 mph or more, then a stiff shaft or extra stiff shaft could be justified to be used by a beginner golfer.
What does 5.0 shaft flex mean?
You know, the 5.0, 6.0, 6.5 and so on printed on the shaft. These numbers correspond with flexes from “regular” to “extra stiff plus”.
Which shaft is best for me?
If your drives carry less than 200 yards, you should probably have Ladies shafts, and if your ball carries between 200 and 225 yards, you should buy clubs with Senior shafts. Generally, if there is a doubt about which shafts you should have, choose the softer shafts.
What is the kick point of a golf shaft?
KICK POINT: Modern shafts, particularly graphite shafts, can produce kick in different sections of the shaft — high kick, mid kick and low kick being three obvious points of reference. Fitters often spend considerable time matching a golfer’s swing with a particular kick.
What is a raw shaft?
RAW: A raw shaft is an uncut shaft that has not been installed in a clubhead. BLANK: This is another word for a raw shaft. When clubmakers refer to a blank, they mean a raw shaft. SPINE ALIGNMENT: Golf shafts, because they are round and hollow, have a spine that is a result of the manufacturing process.
How much does a true temper iron shaft weigh?
True Temper’s Dynamic Gold, the most popular steel iron shaft on the PGA Tour, weighs abourt 130 grams. At the other end of the spectrum, Mitsubishi Rayon has a Bassara graphite driver shaft that weighs about 35 grams. RAW: A raw shaft is an uncut shaft that has not been installed in a clubhead.
What does low torque mean on a golf swing?
Normal measurements are in the 2- to 6-degree range. A low torque number means less twisting of the shaft but also can mean a harsher feel . A high torque number is associated with a soft-feeling shaft, although there may be a sacrifice in accuracy. FLEX: The strength of a shaft as it bends during the swing.
What is the tip of a golf club called?
TIPPING: The tip end of the shaft, which is inserted into the clubhead, sometimes is cut or trimmed to provide more stiffness in the shaft. This is called tipping. While the practice is common on professional tours, it is not widely used among amateur golfers.
Where is the ferrule on a golf club?
FERRULE: The ferrule is an oval piece, commonly made of plastic, that is located just above the neck of the clubhead. Modern ferrules not only are decorative, they are made with great precision to provide accurate and secure bonding between the shaft and clubhead. BUTT: The top end of the shaft, called the butt, is located underneath the grip.
What is torque in swing?
TORQUE: A measurement of the circular rotation of the shaft during the swing.
What is the bend point of a golf shaft?
Bend Point: This is the section in the shaft located from the tip of the shaft where most of the forward bend occurs when a shaft recovers during the swing. If the shaft has a high bend point, the launch angle and resulting trajectory of the golf shot will be low. If the shaft has a low bend point, the launch angle and resulting trajectory ...
What is the OBAN code for butt stiffness?
OBAN uses numeric codes: 2=Senior Men’s, 3=Regular Men’s, 4=Stiff Men’s and 5=Extra Stiff Men’s. These designations are merely those given by the manufacturers and do not relate to each other.
How long is a fairway shaft?
A shaft designed for a driver or fairway wood is typically 46 inches long, but can be as long as 50 inches. These longer wood shafts are typically used in players competing in Long Drive events. Some shafts are designed specifically for fairway woods and are usually 44 inches in length. Hybrid shafts are 42-44 inches in length.
What is the balance point of a 46 inch shaft?
For example, a 46 inch shaft whose balance point is 23 inches from the tip has a balance point of 50%. Shafts that have more weight towards the tip will have a heavier swingweight when assembled. Shafts that have more weight towards the butt of the shafts are said to be “counterbalanced” and will have a lighter swingweight when assembled.
What is a low bend point in golf?
If the shaft has a low bend point, the launch angle and resulting trajectory of the golf shot will be high. This term is also known as the Kick Point. This term is being replaced by Trajectory or Launch characteristics. A High Trajectory or High Launch shaft will have a low Bend Point and visa versa.
Why do golf clubs have spines?
Every shaft will have a spine due to manufacturing tolerances and methods. The magnitude of a shaft’s spine and it’s affect on performance of the shaft when installed in a golf club is a matter of debate among golfers and clubmakers.
How high is torque on a shaft?
Torque can range from the low 1 degree to as high as 8 degrees.
Feedback
I would think the butt section is related more to feel - as the butt is what connects you to the club. The mid section would control stability I guess, since you are swinging the butt, which forces the tip and head to move. I am sure others with more knowledge will be along soon to offer more sound responses than mine.
Feedback
Howard does a good job of addressing some of the effects of butt/mid section flex (vs tip) in shaft fitting - take a good read of post #8 here: http://www.golfwrx.com/forums/topic/909991-diy-driver-tune-up-diy-fitting/
Feedback
In fact in our very recent research in this butt/center performance has tended to cement our findings even more.
Feedback
I had 1 single player where MID section could not be stiff enough for him. He plays the original PL BLUE 75X a true monster shaft, so what ever shaft i got had a softer MID section than the BLUE. What happen was the player lost confidence and club speed.
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
How much weight should a golf shaft be?
Weight. Getting the correct weight of your shaft is an important factor to consider as well. Shafts can range anywhere from 40 to 135 grams. Typically the rule of thumb is that a golfer with a slower swing speed will benefit from using a lighter shaft, and you would add weight as swing speed increases. As you might expect at this point, there are ...
What is the difference between stock shafts and aftermarket shafts?
The difference between stock shafts and aftermarket shafts is usually found in quality control. Many times the bigger OEMs will strip off the paint of last year’s model and give them a new exterior. The graphics look attractive, but you really have no idea what is beneath it.
What is the biggest misconception about golf shafts?
One of the biggest misconceptions about shafts is that there are standards out there that manufacturers adhere to. Most golfers assume that a shaft marked regular or stiff will be the same across the board, no matter who they buy it from.
Why didn't Nick Price find a stiff shaft?
Regardless of the similarity in their swing speeds, Nick Price couldn’t find a shaft stiff enough for his swing because he would apply such an enormous amount of force, whereas Couples didn’t need as stiff of a shaft because of his smooth tempo.
Why is shaft profile important?
Getting the right shaft profile for your swing is very important. It will greatly affect your ability to hit quality shots on the course . There is a lot of confusion in the golf shaft industry. With no standards for performance, the quality greatly varies, and often you get what you pay for. We hope that we have cleared up some ...
What is the most important thing about a driver shaft?
One of the most important things about shafts is how they handle the force that a player’s swing will apply. Generally speaking, there are two extremes. Some players apply a late load to their swing, which would require a stiffer tip of the driver shaft. Conversely, a player that extends early in their swing (most recreational golfers) ...
Is the shaft of a truck the same as the transmission?
It absolutely has an effect on how well you can play. The shaft is similar to the transmission of a car. While it’s not the engine, it’s still extremely important. If you are driving a truck you want a transmission that can handle its particular demands.
What to know about golf shafts?
In today’s guide we will review everything you need to know about golf shafts. Picking out the proper golf shaft is very important as it will impact several components of your golf swing. For example, picking the wrong golf shaft flex can cause you to hook or slice the golf ball. It also can hinder the total distance the ball flies by having too much spin or too low of launch. But don’t worry, at the end of reading today’s guide you’ll be much more educated on the buying process and how to pick out the right golf shaft. Lets Get Started!
What shafts do golfers use?
For most golfers, a graphite shaft works great. Most iron sets are made with graphite shafts as well so you get that material type by default usually unless you specifically seek out steel shafted irons. With steel shafts, you may find that golf shots are easier to control.
How to determine golf shaft flex?
Start by using a launch monitor to analyze your golf swing speed. If your swing ranges between 85 mph and 95 mph then you should start with a regular flex. If your swing speed is faster than 95 mph, then you should try a stiff shaft.
What is the best shaft for golf?
Steel – A steel golf shaft is usually stronger and more durable (less likely to snap) than a graphite shaft. It’s also less expensive and sometimes stainless steel is used in the creation of the steel shaft. There is also two variations, stepped steel and rifle steel.
Why does my golf shaft have a slice?
When the golf shaft is too stiff, it doesn’t unload properly at impact. This can lead to the face staying open and result in a slice golf shot. Beware, a slice isn’t always an indication the shaft is too stiff so if you already have a slice, it could be caused by another fault in your golf swing.
Why do golf clubs have shafts?
During the golf swing the shaft causes deflection (bend) that causes the clubhead to be in a forward and toe downward position relative to the grip of the club.
What is the most common shaft material used in golf clubs?
Graphite Shafts. Graphite – this type of shaft is usually lighter weight compared to a steel shaft but it’s less durable and more expensive to make. Graphite is one of the most common shaft types used in golf clubs and can arguably be considered the main shaft material used, beating out steel.
Why is it important to hold an installed grip before changing the size of your golf clubs?
Because hands (and fingers) come in different shapes and sizes , it's important to try holding an installed grip before committing to changing the size of your golf grips for your entire set of clubs.
What are golf grips?
Golf grips come in either round, ribbed, or alignment shapes. Round is the most popular shape for most grips, meaning you can orient the grip whichever way you prefer (some players like to have the logo of the grip facing up or down, or may choose a 360/no-logo grip ). Ribbed grips have a small protruding ridge, designed to be oriented along the spine of the shaft. This rib, also called a "reminder", helps players feel where the bottom of the grip is, so they know how to properly place their hands. Recently, a more modern and prominent rib design has been introduced by some manufacturers, calling it an " Alignment " or " Calibrate " rib. These alignment grips feature an unmistakable ridge that runs along the full length of the grip.
What are the different types of golf grips?
Golf Grips come in many different styles but pretty much fall into one of these categories: Velvet, Composite, Wrap, Cord, and Hybrid (Cord + Rubber). The Velvet style grip was made popular by Golf Pride's flagship Tour Velvet line, which feature small repeating patterns of crosses using a rubber material. Velvet grips provides a light texture and traction for control without sacrificing feel. The Composite grip was made popular more recently with styles like the Winn Dri-tac and Golf Pride CP2, which feature a tacky and smooth surface that also provide visually enhancing patters and non-slip gripping. The Wrap style grip is actually a simulated 1-piece style but using a wrap design. The Winn Excel is a popular wrap style grip, as well as the Golf Pride Tour Wrap and Jumbomax Wrap grips. Cord grips have cord fabric interweaved through the surface of the grip. This provides traction and added firmness (feedback). The Hybrid style is a newer more modern style grip that utilizes both cord and rubber. The Golf Pride MCC Plus4 is one of the most notable Hybrid grips, which use a softer rubber for the lower hand and cord (for traction/control) in the upper hand.
What is the diameter of a golf grip?
The majority of golf grips have an inside diameter of 0.600" or 0.580". This is because most golf shafts have an outer diameter of this measurement as well.
What is rib grip?
Ribbed grips have a small protruding ridge, designed to be oriented along the spine of the shaft . This rib, also called a "reminder", helps players feel where the bottom of the grip is, so they know how to properly place their hands. Recently, a more modern and prominent rib design has been introduced by some manufacturers, ...
How big is a standard grip?
Every manufacture has a slightly different definition of diameter sizing, but in general Standard grips are around 1" in diameter . Midsize and Oversize/Jumbo grips can vary quite a bit, but in general will range around +1/8" to +3/8" larger in diameter.
Which grip is better for a player with arthritis?
Firm grips tend to provide more feedback to the hands at impact. Soft grips will absorb some of the impact and provide a more comfortable feel. Players that have arthritis or experience hand pain will play better with softer (and/or larger grips).
