
Full Answer
How do you fix a broken Golf Club shaft?
Use a piece of sand paper or a grinder to roughen the tip of the shaft where it connects to the hosel of the club head. Pour epoxy into a container and stir to mix it together.
Can you replace your own golf shafts?
Shafts can be replaced at golf pro shops and most golf stores, but it is also a fairly easy project to do yourself. Replacing your own shaft can save time and money, and allow you to try a new shaft without purchasing new clubs.
How do I clean the inside of the shafts?
Step 1: Thoroughly clean the area to remove all the grease, dirt and other surface contaminants. Step 2: Use a mechanical grinder fitted with a suitable disk to undercut the shaft by 1/16″ (1.5 mm) around the circumference. Step 3: Clean the prepared area with Belzona 9111 (Cleaner/Degreaser) to remove all surface contaminants.
How to epoxy a golf club shaft?
Keep the golf club in an upright position in your golf rack for the curing to be complete. You can add some glass shafting beads to the epoxy before the application to strengthen it and increase its adhesion. A golf epoxy has certain characteristics that make it better than one of those general-purpose two-component epoxies.

What glue is used for golf shafts?
Golf club heads are attached to the golf shaft with epoxy glue. Epoxy is a thermosetting polymer that is a high strength adhesive. Two parts, the resin and the hardener, are mixed together to create a chemical reaction that cures the epoxy to hardness.
Can you use JB Weld on golf shafts?
JB Kwik Weld has a 2451 psi which is just about perfect strength for a golf epoxy and heat tolerance of 230 degrees. The best part is it has a 6 minute working time, 1 hour harden time, and 6 hour cure time.
Can you repair golf club shaft?
Once a golf club shaft has been broken, it cannot be repaired, but it can easily be replaced. Shafts can be replaced at golf pro shops and most golf stores, but it is also a fairly easy project to do yourself.
Can you use regular epoxy for golf clubs?
Unless you have to, do not use non-golf specific epoxies. Use epoxy designed for golf as they usually have higher peel sheer strengths and elastic properties that hold well during impacts specific to a golf club hitting a golf ball.
What kind of epoxy is best for golf clubs?
Best 4 Epoxy Adhesives for Golf ClubsJ-B Weld 8281 Professional-Size Steel Reinforced Epoxy Twin Pack – 10 oz. View on Amazon. ... Brampton Epoxy Pro-Fix 20/20 Long Cure Golf Club Repair. View on Amazon. ... GolfWorks High Strength Epoxy Golf Club Head Shaft Adhesive 50 ml. View on Amazon. ... Permabond Epoxy For Golf Clubs.
What type of epoxy is used for golf clubs?
Permabond offers a range of toughened epoxy adhesives which are suitable for bonding golf clubs. They offer excellent adhesion to carbon, graphite, composite, titanium, steel, wood and many other materials. Cure speed and viscosity can be matched as per the user's preference.
How do you fix a broken shaft?
1:467:16Removing a Broken Graphite Shaft 2019 -Golf Club Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou've got to be able to drill it out with some drill bits. And then you've got to be able to cleanMoreYou've got to be able to drill it out with some drill bits. And then you've got to be able to clean it out so that's what we're gonna do so let's get spotted. All right just like on a shaft repair.
How do you Reshaft a golf club at home?
2:2522:36GOLF CLUB BUILD - How to reshaft your irons Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipUp the house'll. Pull the shafts you don't need a shaft puller. Anything like that you can just heatMoreUp the house'll. Pull the shafts you don't need a shaft puller. Anything like that you can just heat them up and twist them off because it's a steel shaft.
What does it cost to Reshaft a club?
The average cost to reshaft your golf clubs is $24 per club plus the cost of the shaft and grip. A new iron shaft and grip can range between $10 and $95 while a new driver shaft and grip can range between $18 and $440. The majority of the cost comes down to what type of shaft you want and what grips you like.
Can you use Loctite on golf clubs?
1:302:53LOCTITE Success Story: PING Golf - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo they have a steel color with a lock type product that we use in our irons. It actually has a greyMoreSo they have a steel color with a lock type product that we use in our irons. It actually has a grey color to it. So they're using that grey Loctite adhesive.
How do you epoxy a golf club shaft?
4:044:48Hireko Golf Videoblog "Tips on Epoxying a Golf Club" by ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're in the head I just simply use the shaft. And just roll the shaft tip in and then mix it andMoreWe're in the head I just simply use the shaft. And just roll the shaft tip in and then mix it and just put it in in the head.
How long does it take for epoxy to dry on a golf club?
On average, the curing of golf epoxy may take about 12 to 18 hours to get dry on a warm day.
Introduction
This guide will show you how to replace the shaft of a golf club. New golf clubs are expensive, so it is very common to buy golf clubs second hand. A second hand club with a worn out, loose, or warped shaft not only deems itself almost useless, but if used, it prevents a danger in the form of the club head flying off of the shaft swing.
Step 1 Shaft
Use a heat gun to melt the old epoxy holding the club head to the old shaft.
Step 3
Clean out the inside of the club head with acetone and a small wire brush.
Step 4
Place the cleaned club head on the new shaft and mark the where the end of the club head reaches on the shaft.
Step 5
Take some sand paper and sand the shaft past your mark leading to the tip.
Introduction
Steps to replace an old golf club shaft with a new steel shaft and replace an old grip with a new one.
Step 1 Golf Club Steel Shaft and Grip
Using propane or a torch, heat the hosel of the club to remove the steel shaft from the club head. The heat will break the epoxy bond that holds the head to the shaft.
Step 2
Use a wire brush to clean out the remains of the old epoxy from the club head.
Step 3
Use a piece of sand paper or a grinder to roughen the tip of the shaft where it connects to the hosel of the club head.
Step 4
Pour epoxy into a container and stir to mix it together. Once epoxy is mixed together, spin the shaft tip into the epoxy to prepare for insertion into the head.
Step 5
Insert the shaft into the club head. Hold the head and shaft together for approximately 30 seconds to secure.
Step 6
To replace the grip of the club, place the club on a level surface where you can cut a straight line through the grip using a razor blade or a utility knife.
This is the easiest DIY repair for one of the most annoying golf club issues
One of the most annoying things that can happen to a golf club is also one of the easiest things to fix—a rattle in the shaft.
WATCH: Talking TaylorMade Spider GT putters with Bill Price
BK talks with Bill Price, TaylorMade’s senior director of putters, about the new Spider GT putters.
Clement: How to stay with your golf shots and stop swaying
Nothing better than being able to stay with your golf shots and create some powerful leverage to apply some compression through your golf shots like smashing through a door with a battering ram! Get a GOLF SWING WITH LAG, POWER AND SPEED!
Clement: Beat the shanks for good
Editor’s note: Shawn is shouting in his caption, so you know it’s good.
What is an Epoxy for Golf Clubs?
A golf club epoxy is an organic compound that is a type of glue that can be used on golf clubs, to attach a shaft to the clubhead. Knowing how to use a golf club epoxy can be beneficial when your clubs need a quick repair job.
Types of Epoxy used for Golf Clubs
Epoxy adhesives for golf clubs can either be a quick cure epoxy or a long cure. Both adhesives are two-component based. Normally an equal quantity of each component is mixed together.
Golf Club Epoxy vs. General-Purpose Epoxy
Most epoxies will do the intended job but non-golf or General- purpose epoxies that can be purchased at any hardware store, are not recommended. They are not engineered specifically to withstand the unique forces generated by the golf swing. They tend to be brittle resulting in poor peel and impact resistance.
Curing of Golf Club Epoxy
The temperature of the room where the epoxy is being applied and where it will be left to cure is critical to ensure that the epoxy cures properly.
1. J-B Weld 8281 Professional-Size Steel Reinforced Epoxy Twin Pack – 10 oz
The J-B Weld 8281 has a very high tensile strength of 5020 psi that can withstand all the forces exerted from swinging a golf club.It is resistant to acid, water and, cracking from high impact and is very durable and, has a high heat tolerance
4. Permabond Epoxy For Golf Clubs
Easy mixing from the cartridge ( various sizes dependant on the product used) with a static mixing nozzle.
Final Thoughts
If the steps required to fit a shaft to a clubhead are followed correctly then you can easily and correctly fit your selected shafts without having to send them in to be fitted thus saving you unnecessary costs.
Why are shafts worn?
In the mining industry, shafts can become worn or damaged due to vibration, friction and abrasive media. In the marine industry, gland packing and bushing damage to the shaft together with sand abrasion ...
What is shaft wear?
Shaft Wear and Damage. Shafts are a critical component of rotating equipment. Shafts are used to transmit power from one part to another or from a machine that produces power to a machine that absorbs power. Shafts are usually operated in immersed or semi-immersed conditions and are subject to damage by corrosion or chemical attack.
What causes shafts to shut down?
In the marine industry, gland packing and bushing damage to the shaft together with sand abrasion and sea water exposure can lead to erosion-corrosion on shafts. Additionally, oversized keyways, a crucial component that connects the rotating equipment to the shaft, may cause shaft dysfunction. Worn and damaged shafts can shut down ...
Can welding cause damage to a shaft?
If not carefully controlled, these conventional methods will cause residual damage to the shaft. They also require the disassembly of the machine. There are problems associated with welding and thermal spraying. Welding can create heat stresses that will tamper and distort the metal, lowering its load bearing capacity.
Can welding be used to repair metal?
Welding can create heat stresses that will tamper and distort the metal, lowering its load bearing capacity. Metal spraying can only be used to repair damage up to a few 1000s of an inch. These problems and limitations can be avoided by using a combination of polymer tehnology and proven Belzona application techniques.
How to fix a broken golf club?
First remove the old epoxy from the hosel of the broken club. Use sandpaper and abrade the shaft tip that has to go into the club. Clean both the sealing surfaces using a solvent to remove any debris that may cause interference with the epoxy bond. Mix the epoxy components in a disposable container.
How to keep a shaft from getting burnt?
Keep the shaft in a super lock tight shaft holder and tighten it in a vise. If your shaft has a plastic ferrule, cover the ferrule with a wet paper towel so that it does not get burnt.
How to apply epoxy to a graphite shaft?
The steps to apply epoxy are the same irrespective of whether you’re going to fix a steel shaft or a graphite shaft. Measure the tip of your old shaft. Trim the tip end of the new shaft following the trimming instructions so that it is the exact size of the old shaft. Roughen or abrade the shaft tip.
How much epoxy do you need for a golf club?
This will usually be less than 0.5g. A drop is more than enough for the shaft tip.
How much PSI should I use for golf shafting?
Ideally, your golf epoxy should have a PSI number of over 2500 PSI. The GolfWorks shafting epoxy is a great option because of its high torque resistance and shear strength. The epoxy renders 90% curing to 2765 PSI in a day and 100% curing to 3280 PSI in a week.
What is golf epoxy?
What is a Golf Club Epoxy? Golf epoxy is an organic compound that is used to repair and glue together broken parts of golf clubs. Epoxy is formed by a covalent bond between carbon and other elements like nitrogen, oxygen, or hydrogen. This is subject to curing in the presence of a catalyst to form an epoxy resin.
Can you twist a golf club after it has been fixed?
Trying to test the golf head after the prescribed curing period is a good way to check if the curing is complete. If it is done, you’ll not be able to do the twisting. However, the best method is to set aside the remaining mixed epoxy after you have fixed your golf club and check it.
What glue is used to attach golf club heads?
Golf club heads are attached to the golf shaft with epoxy glue. Epoxy is a thermosetting polymer that is a high strength adhesive. Two parts, the resin and the hardener, are mixed together to create a chemical reaction that cures the epoxy to hardness.
What type of epoxy is used for golf clubs?
The two basic types of epoxy suitable for golf club repair are quick cure and long cure. Quick cure is commonly called five minute epoxy and is generally desired only for putters and emergency fixes. Long cure epoxy is better over the life of the club for its higher shear strength.
How long does epoxy cure?
A quick cure epoxy will generally be usable within an hour, while a long cure epoxy will be ready for use in about 20 hours. Epoxy should not be mixed or applied if the surrounding area temperature is less than 65 degrees F. A heat lamp can be used to speed cure time, however, it will result in a weak bond.
Can you use epoxy to reshaft a golf club?
Regular two-part epoxy found in hardware stores can be used to re-shaft a golf club, but it is better to use epoxy designed specifically for golf clubs. Epoxy not formulated for the shear strength required to hold up to high impact will likely break loose.
