
Broken golf clubs occur when golfers slam the club head into the ground out of frustration. Incorrect storage of the club and poor swing technique will also cause shafts and heads to break. Why Do You Keep Breaking Golf Clubs?
Full Answer
What causes golf clubs to break?
Broken golf clubs occur when golfers slam the club head into the ground out of frustration. Incorrect storage of the club and poor swing technique will also cause shafts and heads to break.
Why do my golf clubs fly off the shaft?
The point where the shaft and head meet is connected by special adhesive glue called epoxy. Storing clubs in hot temperature day after day causes the epoxy to break down. And without epoxy to hold your head to the shaft, the club head will just fly off. Solution: Don’t expose your clubs to hot temperatures for long periods of time.
Why does my golf ball hit the shaft instead of the head?
This occurs when the ball is making contact with the shaft instead of the club head. Solution: Only the head is designed to withstand the forces of a golf swing; the shaft isn’t.
Can an incorrect swing damage a golf club?
However I’ve seen enough broken of heads and bent shafts to know that’s not the case. An incorrect swing can certainly cause damage to your club. This occurs when the ball is making contact with the shaft instead of the club head.
What hole was Ben Hogan's 1 iron?
What is the difference between a driver that is just barely conforming for CT and just barely nonconforming?
About this website

Why are golf clubs shaped the way they are?
Finally, irons and wedges sport squarer shapes in their clubfaces, allowing the ball to be struck well if it lies on the ground but also if it sits high on a fluffy lie.
Why is a golf driver face curved?
The curved face of your driver – a design feature called “bulge and roll” – helps your mishits through gear effect. Ever wonder how some of your worst drives still, somehow, manage to find the fairway? No insult to your golf swing, but your golf clubs have a lot to do with that.
What were old golf club heads made of?
These golf clubs were made up of wood with the shafts being made from ash or hazel and the club heads being made from tougher wood like apple, holly, beech or pear. The club head would be connected to the shaft with a splint and then bound with a leather strap.
How long do golf club heads last?
A good set of golf irons can last anywhere between 8 and 12 years, or 300 rounds of golf. Of course, this number can vary depending on a number of factors. The golf iron head is built to last and be extremely durable.
Why are golf drivers not flat?
Driver Bulge A clubhead's horizontal curvature is known as its bulge, which is designed to partially counter the gear effect. If you hit the ball closer to a driver's toe, the face imparts sidespin that causes the ball to hook -- curving to your left, if you're right-handed.
Where is the sweet spot on a driver?
On almost every driver we test, the sweet spot that creates the highest ball speed is slightly towards the toe and slightly up from the center of the face. If you miss your shots high on the face, the ball will launch higher, spin less, and you will lose ball speed.
Are 30 year old golf clubs still good?
There is no evidence that golf clubs deteriorate over time. Well maintained clubs will last a lifetime. 10+ year old clubs should be checked for better options but clubs less than 5 years old do not need replacing except for wear and tear issues to which wedges and forged irons are most vulnerable.
What golf club is called a mashie?
Mashie – this is an old name for a golf club used for approach shots. The modern equivalent of this would be the 5-iron club.
When did woods stop being wood?
In the mid-20th century, both the USGA and the R&A ruled that golf clubs with steel shafts could be used in tournaments. While steel was used for club shafts, wooden heads were the norm for drivers and fairway woods until the 1970s.
How far does the average golfer hit their irons?
The average golfer hits their 7 iron 145 yards, but the average distances will vary between 128 and 160 yards. Golfers in their 20s typically hit the ball the longest, and the distance tends to decrease as the golfer gets older.
Do golf drivers go dead?
A golf driver can go dead and lose its pop when there is a crack, or defect, in the club face. This can be caused by faulty manufacturing or weakness in the driver head, and affects distance and performance.
Should I sharpen the grooves on my irons?
The grooves on your golf club are vital to both backspin and ball control on the golf course. Sharpening the grooves may be something that you have never considered doing before - but worn down grooves will not give you the control or backspin you're looking for.
What does a twist face do on a driver?
Revolutionary new face curvature designed to deliver a corrective face angle on off-center impacts, producing straight distance off the tee.
What does an upright lie on a driver do?
The upright lie also promotes a left tilting spin axis, which leads to what's generally described as draw spin. An upright lie angle basically gives you a head start, but depending on the severity of the slice conditions the golfer generates, it certainly won't guarantee a draw.
What is bulge and roll on a driver?
The face of every driver (all clubs requiring a headcover for that matter) has roll and bulge while irons do not. Bulge is the curvature of the face from its heel to its toe, while roll is the curvature of the face from the crown to the sole.
What is the difference in golf drivers?
Most manufacturers will offer drivers in regular (R), stiff (S) and extra stiff (XS) shaft flexes. Other flexes include light or ladies flex (L), senior (A) and more extra stiff options (XXS, XXXS). Typically lighter, less stiff shafts will produce a higher, right-to-left biased ball flight.
Golf club life expectancy - How Long Do Clubs Last - AEC Info
Updated on May 5th, 2022 at 10:56 am. Given how expensive golf clubs can be, you may wonder how long they’re likely to last. Golf clubs have an expected lifespan, and thus, it’s important to know their limits when shopping.
Do irons lose some distance as they get older? - The Sand Trap .com
I wouldn't trust the launch monitors for acuracy, the only was to compare to your old clubs is to hit the side bt side as Shindig said. I was demo-ing some Mizzuno MX200 last year in AZ and the PGA Superstore launch monitor said I was hitting the 6i 25yds further than mine, the sales guy was quite pushy, I said I would go and get my clubs and hit the side by side and he said I couldn't do that ...
Why do golf clubs break?
Golf clubs can break due to user error. Broken golf clubs occur when golfers slam the club head into the ground out of frustration. Incorrect storage of the club and poor swing technique will also cause shafts and heads to break.
Why Do You Keep Breaking Golf Clubs?
There was a time when golf clubs were handmade one by one. These classic clubs were made from 100% steel. While they were practically unbreakable, they’re no match for the modern graphite and hybrid clubs we have available today.
How Long Is My Golf Club Under Warranty?
Disclaimer: I have gathered a list of the warranty periods for each of the major golf club companies. This list was accurate of 23/03/19 and should be used as an approximate guide only. Please check with your manufacture for correct warranty information.
What is a Project X HZRDUS shaft?
What is the Project X HZRDUS Black Fairway Wood shaft? Project X HZRDUS Black Fairway Wood shaft is a low spin golf shaft design. It comes with enhanced firmness over the entire length of the shaft....
Why do golfers smack their clubs into the ground?
It’s not uncommon to see golfers smacking their club into the ground out of anger . Obviously clubs were not designed to withstand such punishment. If you do find yourself with an anger problem on the golf course, you’ll find yourself visiting the golf store in no time.
Why are counterfeit golf clubs so cheap?
While counterfeit clubs are much cheaper than the real deal, there’s a reason why they’re so cheap. Unknowing golfers may not understand how one steel club is different to the other and choose to save some one on a clone. Counterfeit drivers and woods are particularly prone to a short life expectancy.
How to keep golf clubs from splitting apart?
A wet shaft will eventually turn into a rusty heap of metal, causing your club to crack or split apart. Solution: Store your clubs indoors or outside under shelter. After playing a game of golf in the rain, use a towel to dry off your clubs. When washing your clubs, use as little water as possible.
What hole was Ben Hogan's 1 iron?
Ben Hogan’s famous 1-iron from that majestic 72nd hole approach shot in the 1953 U.S. Open at Merion, while practically unhittable for mere mortals, likely would respond just fine today if it was removed from its case at the USGA's Golf House. (The leather grip and shaft might not have held up so well, of course.)
What is the difference between a driver that is just barely conforming for CT and just barely nonconforming?
Certainly not with a human golfer’s swing. The difference between a driver that is slightly below the conforming limit on the CT test (239 microseconds) and just over the limit of the tolerance zone (257 microseconds) might be a couple of yards. Maybe. But the facts are that there are virtually no drivers being used by tour players that would have ever been under the CT limit to start. What we’ve been told by manufacturers many times over the years is that everybody is designing and manufacturing drivers within and to the edges of the CT test’s tolerance zone. That would mean that should a driver’s face start to creep toward a nonconforming level of flexibility through some kind of micro-fissures or metal fatigue based on repeated strikes at high speeds in the center of the face, that improved benefit of a more flexible face will be staggeringly less than a couple of yards. More like inches. And even then, there is some evidence that while that “improvement” might happen in as few as a couple thousand hits, it also might be very short-lived before that face, instead of becoming more flexible, just becomes dead or even caves in. That said, one result of the PGA Tour’s efforts to test more drivers on a random basis is to get players to test their drivers with manufacturers more often. Also, another intended result is perhaps to get manufacturers to play a little safer with regard to the rules. Of course, you could ask why a player/manufacturer would be playing with that kind of fire, but that's another issue, which only makes sense if you’re trying to convince a tour player this new driver is really hotter than his old driver.
Why offset golf club at impact?
An offset helps you achieve this as you are learning how to play.
When you switch to non offset golf clubs, do you need to start getting your hands into a more aggressive position at?
When you make the switch to using non-offset golf clubs you need to start getting your hands into a more aggressive position at impact. At first you may hit a few weak and “slappy” shots because you have lost a feature that you may have relied on. You will get used to it, don’t worry, just practice.
What are progressive offset irons?
This is what I have been describing, as the loft on the irons increases and the shaft length gets shorter, you need less offset as your swing speed is decreasing. This means that you have that bit more time to make the adjustments at impact and less offset is needed. This method also reduces your reliance on the offset.
What is offset golf?
Tom Wishon founder of Tom Wishon Golf Technology and one of the world’s finest clubmakers says: “Offset is a design condition in clubheads in which the neck or hosel of the head is positioned in front of the face of the clubhead, so that the clubface appears to be set back a little from the neck ...
How to get better at golf with less offset?
Try to practice a lot on the clubs with less offset, the shorter irons 8-PW. These will let you see if your swing is starting to improve with less influence from offset which is key to becoming a better golfer.
Why does my swing slice?
A slice is caused by poor swing mechanics which the offset is able to reduce the effect of. It doesn’t actually change how you swing it, you must keep that in mind.
Why is offset important in golf?
An offset helps you achieve this as you are learning how to play. This feature increases the chances of you getting your hands to the ball before the club and reduces thin shots. It helps you present the face of the club nicely and should give you better ball-striking.
What is a maraging golf club head?
Another more recent addition to the number of materials used in golf club head manufacturing is maraging steel, which is an alloy or family of steel with unique properties. Typically maraging steels are harder than non-maraging steels like 431 or 17-4 and used primarily for face inserts rather than the whole head.
Why use titanium in golf clubs?
Second, the reason for titanium is for the strength and lightweight nature.
What is the maximum size of a golf driver?
Drivers can also be made of 17-4, but due to the high density of the material, the limit on size is approximately 250cc without the risk of cracking during normal play. Because golfers prefer larger, easier-to-hit drivers, virtually no drivers today are even manufactured from stainless steel.
Sassafrass
A few hours ago I was at the range working on my priority piece. Everything was great. I was making the best contact I've made with the ball in a long time. About halfway through my bucket my club head of my 7 iron snapped off after making contact with the ball...
vangator
I've only snapped 1 iron head. When I clean my clubs, I try to not get any water down the shaft. The shaft will rust from the inside. That's probably why it snapped. One year sees short, but who knows. I build my own, so I can't blame anyone but me.
Sassafrass
Did you register them? Do you have the seriel number, I don't know which iron in the set they mark however, sometimes the seven. Contact them.
Duff McGee
So it appears never cleaning my old irons was a wise choice after all....;)
Dirtsquirrel
Looks like a lot of epoxy inside the shaft up where it snapped off. Read somewhere that using too much epoxy when glueing the head on forces glue up the inside of the shaft crating a "break point" when the shaft flexes. I'm sure some experienced club builders or repair guys could weigh in on this.
vangator
That does seem like a lot of epoxy. I've never checked mine, but I don't think I get epoxy that far up the shaft. Does it look rusty where the break occurred?
rkim291968
Has anyone ever snapped the club head off their club taking normal shots?
celts5407
is that a serious question? you'd be crazy to hit the clubs with the epoxy breaking down. your going to damage the tip of the shafts by hitting them when they are loose. if they arent epoxied securely the tip section can fray and the shafts will be ruined.
PepsiDuck
Thanks for the responses...just confirmed my initial thoughts...and no, I don't think it's just a loose ferrule...I am able to twist the shaft from the clubhead...it just takes a little bit of effort...guess I'm stuck with hybrid off the tee for a little while....
PepsiDuck
I understand the point that I shouldn't be hitting with the clubs...but all else aside, would having a clubhead that is that far off the shaft affect ballstriking with that club...?
Rohlio
Why can't you just re-epoxy them yourself? it would take about 15 mins. at most.
Why does my golf club break?
When this happens, it’s usually the result of some type of inconsistency in the metallurgy of the club.
What does it mean when a golf club bends its loft?
Bending the loft is another story. Bending the hosel toward or away from the face plane, opens or closes the club’s face angle. This will change the trajectory of the ball, and can potentially cause misdirected shots.
How to improve golf ball flight?
Using a club bending machine to change the angle on a golf club is among the fastest ways to improve a player’s ball flight. Whether it’s changing the lie to improve accuracy or changing loft to make sure that the player’s clubs are progressively consistent, angle bending is a major factor in club performance.
What is clubhead registration?
NOTE: Clubhead registration is the key element when bending or measuring clubs. Proper registration requires the club to be clamped securely in the bending machine with the face square and horizontal by positioning the club’s score lines parallel to a horizontal reference point.
What are some of the facts about club adjustment?
Here are some of the facts, and fallacies, about club adjustment. 1. A manufacturer’s new set of clubs doesn’t guarantee accuracy. While golf club manufacturers certainly try to make a consistent product, there are often inconsistencies in the lofts and lies of the clubs and they may not be progressively consistent from one club to another .
Can metal wood be bent?
Even with limitations, many of today’s metal woods are indeed bendable, especially stainless-steel head s. Forged titanium models are bendable as well due to their softer titanium structure. And provided the hosel of the wood is long enough to allow the bending bar to fit over its length, metal woods can be bent to custom-fit a player. This applies to both face angle and lie.
Why is the cylinder head warped or deformed?
If you have ever unmounted the car engine o separated the cylinder head from the engine block most of the time to change the cylinder head gasket that was burned or used excessively, or for other common reasons such as the car consuming too much oil or coolant , you may have noticed that the cylinder head does not look good , and after you do a flatness test you will notice that it is warped or deformed, not always, but most of the time.
What causes a cylinder head to fail?
Failure to comply with the manufacturer’s specifications for engine maintenance is the main reason for the cylinder head failure.
What happens when a cylinder head gasket is loosened?
Once the screws are loosened, the cylinder head can bend and twist, and the cylinder head gasket can no longer properly seal and either affect the compression of the engine or allow water or oil to leak inside or outside the cylinders. If the cylinder head gasket allows for compression leakage, high pressure is generated in the cooling system, ...
What is the problem with aluminum cylinder heads?
This means that it no longer offers a flat surface to keep the cylinder head gasket in the correct position, which can later lead to costly problems, in the form of major repairs or total engine replacement. Bending or warping is a common problem for the aluminum cylinder heads.
How rough is a cylinder head?
In modern engines, the roughness of the flat surface of the cylinder head should be 10 microns , since most use a sheet cylinder head gasket, called the M.L.S. Because the M.L.S sealing material is inert, any malfunction of the cylinder head surface finish can lead to cylinder head gasket failure.
Why is my cylinder head warping?
Why is the cylinder head warped? Usually, this phenomenon happens due to engine overheating, so the main cause is poor or insufficient engine cooling. The main causes that lead to insufficient cooling of the engine are: poor quality oil, poor quality coolant, either the engine has been modified excessively, especially in stage 2, ...
What happens if your engine stays hot?
If the engine stays hot and you continue to drive very aggressively, then the engine temperature will increase to reach the point where the cylinder will deform.
What hole was Ben Hogan's 1 iron?
Ben Hogan’s famous 1-iron from that majestic 72nd hole approach shot in the 1953 U.S. Open at Merion, while practically unhittable for mere mortals, likely would respond just fine today if it was removed from its case at the USGA's Golf House. (The leather grip and shaft might not have held up so well, of course.)
What is the difference between a driver that is just barely conforming for CT and just barely nonconforming?
Certainly not with a human golfer’s swing. The difference between a driver that is slightly below the conforming limit on the CT test (239 microseconds) and just over the limit of the tolerance zone (257 microseconds) might be a couple of yards. Maybe. But the facts are that there are virtually no drivers being used by tour players that would have ever been under the CT limit to start. What we’ve been told by manufacturers many times over the years is that everybody is designing and manufacturing drivers within and to the edges of the CT test’s tolerance zone. That would mean that should a driver’s face start to creep toward a nonconforming level of flexibility through some kind of micro-fissures or metal fatigue based on repeated strikes at high speeds in the center of the face, that improved benefit of a more flexible face will be staggeringly less than a couple of yards. More like inches. And even then, there is some evidence that while that “improvement” might happen in as few as a couple thousand hits, it also might be very short-lived before that face, instead of becoming more flexible, just becomes dead or even caves in. That said, one result of the PGA Tour’s efforts to test more drivers on a random basis is to get players to test their drivers with manufacturers more often. Also, another intended result is perhaps to get manufacturers to play a little safer with regard to the rules. Of course, you could ask why a player/manufacturer would be playing with that kind of fire, but that's another issue, which only makes sense if you’re trying to convince a tour player this new driver is really hotter than his old driver.
