Golf-FAQ.com

why does my club car golf cart still run when i stop pressing the gas

by Dr. Paxton Metz MD Published 2 years ago Updated 2 years ago

Full Answer

Why does my club car golf cart keep running?

Why does my Club Car golf cart keep running? Most club car users face this problem. Mainly the problem occurs if the OBC or On-Board Computer is not functioning correctly. OBC monitors and controls the overall functioning of the car.

Can you turn off a golf cart if it is not working?

If still, it’s not working, you can perform troubleshooting and turn off your car. Why won’t my Club Car golf cart shut off? The problems with a club car golf cart appear when either the OBC or the solenoid is not functioning correctly.

Why does my golf cart cut out at full throttle?

A golf cart may cut out at full throttle due to a faulty solenoid that needs replacing, or having too low of a battery voltage. Solenoid needs replacing: It may be that the solenoid of the Golf Cart may have developed some glitches due to which it is not responding at full throttle.

Why won’t my club car turn off?

As solenoid runs together with the club car, at fault in it can cause the above problem along with others. In some cases, faulty batteries can also be the cause of the problem, as mentioned earlier. A club car may seem a compact vehicle, but a lot is going on in it. So there can be several reasons why the car won’t shut off.

Why does my golf cart keep running when I stop?

Yamaha golf carts can keep running and not stop for many reasons. It's usually loose wiring, a sticking accelerator stop switch, a sticking solenoid or issues with the engine stop relay or the voltage regulator.

Why won't my golf cart shut off?

Troubleshooting. Switch the car to neutral before turning the key off. The problem with shut down may have occurred from the kill circuit, which is controlled by the top microswitch. You may have to replace the microswitches or solve the problem by tightening up the circuit.

Where is the speed sensor located on a Club Car golf cart?

The speed sensor in a Club Car Precedent golf cart is located on the back of the motor. To remove the sensor, unplug the cables behind the motor. You can use a 5/16-inch socket to remove the pigtail connector and pop off the plastic housing that encases the speed sensor.

How do you reset a gas golf cart?

Easily Reset the Club Car Golf Cart OBCKey switch to off.Set forward/reverse to neutral.Put tow/run switch to tow.Disconnect the negative battery terminal from the battery pack.Put the tow/run switch to run.Put forward/reverse switch to reverse.Put key switch to on.More items...

Where is the reset button on a Club Car golf cart?

Identify your main battery supply (usually the largest battery) on your motor. Check around this supply for a small red button that may or may not be labeled “Reset”. Press and hold this button for a few moments and then release it to reset the motor.

Where is the reset button on a golf cart motor?

First, you'll want to reset your motor. It should have a small reset button (Usually it will be red) located near the main battery supply. Hit the reset button and then put the cover back on the motor. The next step would be to recharge your cart and try turning it on again. If it starts up then you're in luck!

How do I know if my speed controller is bad on my golf cart?

When your golf cart's speed controller isn't operating correctly, your cart will show it by running erratically or failing to drive at one constant speed. If your cart starts showing these symptoms, the first thing you should look at is your speed controller.

How do I test my club car speed controller?

How to Test Club Car Precedent Controller? To test a club car precedent controller, connect a voltmeter between the negative terminal of your cart's battery and the M terminal on the controller. Then push the pedal down and look for a clicking noise from the solenoid. Your batteries should read as full.

How do you remove the speed limiter on a club car?

0:040:46How to remove governor on a Club Car golf cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou open up this box lap. Here. It looks up look inside. There's 12 cable down right here this leverMoreYou open up this box lap. Here. It looks up look inside. There's 12 cable down right here this lever you want to lift up and Bend and that pulls on the cable a little more.

How do you adjust the carburetor on a Club Car golf cart?

Find the pilot adjustment screw on the edge of your carburetor. Pay attention to this screw – it should be a sharp point and not flat. Carefully remove this screw and then carefully screw it back. Turn this screw out one and one-half turns to adjust it properly.

How do you adjust the governor on a Club Car gas golf cart?

If you find this rod, then your governor can be easily adjusted by accessing the cart's inner workings. Simply adjust the cable coming from this metal protrusion, turning the nut counterclockwise to make the cable longer, effectively adjusting the cart's governance to increase the overall speed.

How do you adjust the governor on a gas golf cart?

Adjusting an EZ-GO Golf Cart GovernorStep 1 - First, lift the seat of your engine to reveal seat cousins. ... Step 2 - Remove the seat cushions over your motor. ... Step 3 - Remove the black plastic cover to expose the motor. ... Step 4 - Loosen the smaller one and tighten the larger one to increase your cart's speed.More items...•

Where is the speed sensor located?

0:571:38Vehicle Speed Sensor Location - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo if you ever want to know where the vehicle speed sensor is this is where it is way back behindMoreSo if you ever want to know where the vehicle speed sensor is this is where it is way back behind the engine all right so that's a little look at where the VSS is located.

Can you bypass speed sensor on golf cart?

The speed sensor on the EZGO golf cart can be bypassed by unplugging it from the speed controller. By disconnecting the J5 pin on the speed controller, this will cause the golf cart to creep along as the controller will go into limp mode. Bypassing the speed sensor on a EZGO golf cart is not recommended.

How does club car speed sensor work?

The speed sensor on a golf cart is used to interpret the rpm of a motor. From there, it then passes this information to the speed controller found in the cart. The point of this device is to keep control of the many motor functions that exist. This includes regenerative braking and a protection called roll away.

What controls the speed on a golf cart?

Essentially, your golf cart's speed controller sends its current and battery voltage to its motor. This process depends on your golf cart's input device, which includes its throttle. That's how your golf cart's speed controller lets you operate its acceleration rate, as well as its deceleration rate.

1. Speed Sensor Issues

The speed sensor is an essential and critical part of golf cart operation that helps to ensure that cart runs smoothly and efficiently. It operates by measuring how fast you are driving and how much electricity is needed to maintain that speed. When the speed sensor ends up running into trouble, chances are your cart may end up running slowly.

2. Low Battery

Usually, the most common reason golf carts slow down is when they don't get enough power output from the battery. If the battery pack charge is very low and your cart is out of power, your cart will run slow.

4. Bearing Encoder Issues

The bearing encoder is an essential part of your golf cart that provides you with careful electrical charge distribution throughout your cart. It works by encoding various elements of your cart's operation and translating them to different impulses to keep the power running smoothly.

5 Ampacity Controller Fault

The Ampacity controller is a part of your cart that helps to manage the amperage that produces and uses as your cart drives. When this particular part malfunctions, you're going to run into some issues with your cart operation.

How to Increase your golf cart speed?

Are you looking to increase your golf cart speed? Learn more about how to make your golf cart go faster.

Why does my golf cart keep powering off?

If the cart starts powering off after a new installation, then you will know that the issue is caused due to errors with the installation.

What happens if you charge your golf cart?

You would have charged up your cart fully but after driving it around for an hour or two, the power would have got drained off completely. If this is a frequent occurrence with your cart, then you will need to take a look at the batteries.

How to check battery water level in golf cart?

How to Check Battery Water Levels in a Golf Cart. Check if the voltages in both the batteries are at the designated levels. Also, if the water in the batteries has dried up, it could cause this issue. Check for the electrolyte and water levels in the batteries. Make sure that you are not overcharging or undercharging your batteries as these could ...

Why does my cart have a loose solenoid?

If the connections from the solenoid have become loose or if there is some other loose contact, the cart might behave in this manner. It can also be caused by a faulty motor or a faulty key switch.

Why does my golf cart cut out?

Another reason why golf carts can cut out is due to problems with the battery voltage or water levels.

Can you fix a golf cart on your own?

Under NO circumstances should you attempt to fix your golf cart on your own. Doing so is dangerous and could result in serious bodily harm. The information on this website has not been verified for accuracy and should only be used for general information purposes only. Use this information at your own risk.

Is my speed sensor broken?

There is a magnet associated with the speed sensor. Sometimes your speed magnet may be broken but will still be clinging on; only being held by the screw. Unfortunately, you may not realize it is broken until you take the mechanism apart. The speed sensor may not even show any issues. Check if the magnet is broken and if it is, ...

Why does my golf cart spin out?

The brake bub will spin out when there is too much load to prevent any damage to the rear axles, causing the golf cart to stall on hills. Remove the covers from the rear wheel. Notice the castle nuts that are holding the hub to the axles. Apply the brakes.

Why does my golf cart stall?

The most common reason why your golf cart is stalling is due to a bad solenoid or a faulty speed controller. Batteries have lost charge. Faulty ignition. Problem with the direction switch. Faulty speed controller. Bad solenoid. The solenoid wears out every time the gas pedal is pressed down. The solenoid gets pressed down to a thin plate.

Why does my EZGO golf cart hesitate?

The main reason why an EZGO Gas golf cart hesitates while accelerating, is because of a dirty carburetor. A dirty carburetor causes this hesitation. Regular cleaning can prevent this problem. Check the rubber boot and clean if you spot any dirt. In case it has worn out too much, you can replace the carburetor.

How to check for leaks in golf cart?

You can check for any leaks by following these steps: Crank up the golf cart and check every seal for leakage. You can also spray wd40 at the clutch to find leaks. When the cart becomes hot, the voltage also drops. So, make sure you provide enough voltage to the batteries so the cart can run.

Why is my EZGO RXV hesitation?

In most cases, the hesitation problem occurs due to bad batteries. If you have bought new batteries for your EZGO RXV, make sure to fully charge them before the first use. Batteries should then be charged after every use. To keep the batteries in check, get a Digital MultiMeter to measure the individual voltage.

Why does my cart stutter?

If you change the battery, change the charger as well; otherwise, the battery will keep running down. If your cart seems to run fine for a few feet, and then it stutters, it is most likely the batteries. If it is not the battery, then check if it is the speed controller or the resistor.

What causes a cart to heat up?

Weak batteries. Bad connection between the batteries. If there are loose connections, it will cause heating in the battery. To check, you can drive your cart for a while and feel the temperature in the cables and connections. If there is no heating, then check the individual voltages.

Why does my club car golf cart have no power?

The main reason why a Club Car golf cart has no power is due to a faulty regulator or bad battery. One of the most common reasons could be a bad regulator and the connections to the regulator needs to be checked.

Why does my golf cart lose power when going uphill?

The reason why a Club Car golf cart loses power when going uphill is because of a worn out or loose drive belt. Check if the Drive Belt is worn out or is dangling loose. In such case get the Drive Belt replaced. Get both faces of the Drive Clutch inspected, to verify if the faces are grooved. If the Drive Clutch is not working in order, get it ...

What happens if no continuity prevails when the solenoid is hooked to the batteries?

If no continuity prevails when the solenoid is hooked to the batteries, better to get the solenoid replaced. Get the load test gone on the batteries. It may be that one or more of the batteries are failing to get hold of the significant load capacity that is being offered.

Why is my solenoid yellow?

One of the most common reasons could be a bad regulator and the connections to the regulator needs to be checked. The solenoid must have at least 12V charge while being operational which needs to be validated. The yellow from the starter set of the coil should touch the ground or get connected close to the frame.

What happens if the battery pack is not compatible?

If the battery pack is not compatible, the transformer could be overheated. The casing on the 48 must not be dropped or damaged. If the battery pack is damaged, please ensure the same is not fitted to the cart since it may result in the cart getting caught on fire.

Is the Ping G25 adjustable?

Is the Ping G25 driver adjustable? The Ping G25 driver is adjustable. It’s possible to do four adjustments using the hosel adapter of the driver apart from the stated loft setting and...

Can a DC plug be plugged into a club car?

The DC plug has to be fixed to the wall before it is plugged to the Club Car. Connect the Club Car end of the 48 into the receptacle on the Club Car. In case the DC is plugged in too fast, it may cause the Power Drive 48 to lose connection. The battery pack should be compatible with the PowerDrive 48.

Club Car Precedent 48v Intermittent Problem Question

I have a 2012 Club Car Precedent 48v electric cart that will suddenly stop working. It has brand new batteries, and seems fine, but randomly will not move when pushing the pedal. It will lurch forward then stop again, or it may work normal after changing the f/r switch, key switch, or even the run/tow switch.

Answer

It sounds like you are dealing with what we classify an intermittent problem. So, first things first, we need to reproduce the problem. Most likely, you are dealing with a connectivity issue. Essentially, what you are describing is a power outage to the system. The clicking noise you are hearing is the solenoid disengaging due to lack of power.

Why does my golf cart keep turning off?

When a Golf Car is shutting off without warning, it’s because of low battery voltage, dead batteries, or because the solenoid coil is overheating. Low battery voltage: Sometimes a dip in the minimum voltages of both batteries causes the Golf Cart to turn off randomly. It is best to use a voltmeter and check if the voltages ...

What happens if the voltage goes down on a golf cart?

Again, when the voltages go down, it will hit minimum and all the power that is gained shall be lost.

Why does my Yamaha G2 keep shutting off?

Yamaha G2 golf cart keeps shutting off: The Yamaha G2 Golf Cart may keep shutting off due to one of the following reasons: Loose solenoid wiring: The first check should be done whether the wiring on the golf cart is in right condition.

How to fix an EZGO golf cart?

The ways to fix a EZGO are stated below: Check the Solenoid contacts: The wires connecting the solenoid may not have electricity flowing due to which the Golf cart is getting abruptly shut off. It is recommended to change the wires connecting the solenoid and check if the problem gets sorted.

Why does my golf cart cut out?

A golf cart may cut out at full throttle due to a faulty solenoid that needs replacing, or having too low of a battery voltage. Solenoid needs replacing: It may be that the solenoid of the Golf Cart may have developed some glitches due to which it is not responding at full throttle.

Why is my controller not connecting to the solenoid?

It is advisable to check the connections out there to check if the wires are getting disconnected.

Can you replace solenoid on golf cart?

Replacing the solenoid helps in most cases but it is advisable to get it checked at an authorized service center. Battery voltage is too low: In many instances, the batteries may not be carrying adequate amounts of voltage to keep the Golf Cart in running order. The voltages of the batteries should be checked via a voltmeter to see ...

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9