Golf-FAQ.com

why won't my golf cart go

by Mr. Lafayette Rau Published 2 years ago Updated 2 years ago
image

There are several reasons why your club car won’t move:

  • Batteries; in a pack of 3 or 4 batteries even if one fails, the required power won’t reach the motor
  • Solenoid
  • Wiring and connections
  • Controller
  • OBC
  • F & R switch
  • Resistor & Diode

Solenoid Wear
When there is a disruption in the flow of the electrical current, your cart will not operate. A common reason for current disruption is solenoid wear. Each time the solenoid activates as you press down on the gas pedal, the solenoid compounds down onto a thin metal contact plate.
Apr 4, 2018

Full Answer

Why is my golf cart not working?

Your golf cart won’t start if there is a problem with the fuel, airflow, or electrical system. Any one of these areas can cause your golf cart to fail to start. Try these steps to troubleshoot and pinpoint the exact failure point. First, you turn the key, press the pedal, and listen for a click. If nothing happens, it’s most likely an electrical issue.

How can you slow down your golf cart?

A Club Car golf cart will not move if power from the battery pack is not reaching the motor. Faulty parts such as the solenoid, OBC and wiring can also cause a golf cart to not move. There are several reasons why your club car won’t move: Batteries; in a pack of 3 or 4 batteries even if one fails, the required power won’t reach the motor; Solenoid

What is wrong with my golf cart?

Troubleshooting: Electric Golf Cart Will Not Run Step 1. Check the battery connections. Make sure the battery terminals are all connected and free of erosion. Step 2. Test the batteries. Disconnect the cables from the battery terminal using a flat-head screwdriver. Using a... Step 3. Reset the ...

What is wrong with the golf cart?

Apr 04, 2018 · When there is a disruption in the flow of the electrical current, your cart will not operate. A common reason for current disruption is solenoid wear. Each time the solenoid activates as you press down on the gas pedal, the solenoid …

image

What do you do if your golf cart won't go?

First, try this: turn the key switch on, hit the accelerator, and check for a clicking noise. If you don't hear clicking, it's time to take a look at your cart's batteries. Make sure the battery is fully charged and the terminals are cleaned and secure. Next, see how the water level in the battery is holding up.Feb 24, 2016

Why does my golf cart click but not move?

A damaged battery or damage to the internal controller could cause your club vehicle to make a clicking sound but not move. Due to dust building inside the battery ports, a Club Car golf cart can start clicking but not move. These are the causes of clicking sound on the golf cart but won't move, among others.Sep 6, 2021

Why does my golf cart not accelerate?

If your golf cart does not accelerate, there is a possibility of the damaged solenoid. The solenoid is basically an electrical switch that enables the battery's flow from the battery into the motor. Check out the signs of the bad solenoid.May 10, 2021

How do you diagnose a golf cart problem?

There are a few simple problems that you can fix yourself that will not necessitate professional maintenance.Test the wall socket where you charge your cart. ... Expose your golf cart batteries. ... Test the batteries for voltage. ... Replace dead batteries. ... Expose the motor for inspection. ... Reset the motor. ... Test the cart.

Why won't my golf cart go forward or reverse?

Most of the time golf carts won't work in forward or reverse due to the shift cable being broken, electrical issues, ignition switch issues, or a too low idle speed. There are also a varying amount of other reasons it will not work as well such as the transmission has gone out.Dec 7, 2021

Why is my electric golf cart not working?

If you try to start your cart and don't hear that “click,” it's likely an issue with your solenoid. If you're lucky, the problem could be as simple as a loose wire or a broken coil. In some cases, corrosion can also be a factor. If you suspect a faulty solenoid, your best bet is to take your cart to a repair shop.

How do I know if my golf cart solenoid is bad?

If your golf cart fails to turn on when you turn the key on, this is the most obvious sign of solenoid failure. The solenoid clicks a little with the ignition system in regular operation; in most cases, a failing solenoid will not snap.

How do I reset my electric golf cart motor?

First, you'll want to reset your motor. It should have a small reset button (Usually it will be red) located near the main battery supply. Hit the reset button and then put the cover back on the motor. The next step would be to recharge your cart and try turning it on again.Feb 12, 2018

Why is my gas golf cart losing power?

Over time, your wires may work themselves loose from their connectors or end up with damaged connectors, frayed with common corrosion issues. However, there is also a chance that your wires may end up broken or frayed, leading to sparks and poor electrical conduction.

Where is the reset button on a golf cart?

Identify your main battery supply (usually the largest battery) on your motor. Check around this supply for a small red button that may or may not be labeled “Reset”. Press and hold this button for a few moments and then release it to reset the motor.

How do you know if your golf cart motor is bad?

You have enough going on in your life without your golf car refusing to start when you turn the key in the ignition. If your golf car won't start, is slower than it used to be, or is experiencing other technical problems, you could have a bad motor on your hands.May 14, 2021

Why won't my electric golf cart start?

As the main source of power to your electric golf cart, the batteries are commonly the cause for why your electric golf cart won’t start. Acid-based batteries are typically used for electric golf carts and must be recharged in order to work properly.

How to reduce golf cart issues?

However, the best way to reduce your chances of golf cart issues, later on, is by performing regular preventative maintenance. With preventative maintenance, you can extend the life of your golf cart and potentially save money in the long run.

What is the best way to check if a golf cart battery is charging?

A Battery Hydrometer: A battery hydrometer measures the specific gravity of the electrolyte solution and can indicate whether or not your batteries are charging correctly. This method is inexpensive and reliable, making it a popular choice for golf cart owners.

Why does my golf cart make a clicking noise?

The solenoid is a critical component of your golf cart because it is the main switch that connects the current from the battery to the traction motor. That clicking noise that you hear when you press the gas pedal is the solenoid.

How to test golf cart batteries?

Another method to test your batteries is by using a load tester. Battery load testers can come in a variety of different price ranges. They give golf cart owners the ability to monitor their battery’s voltage to see how much the volt drops during testing, which indicates the health of the batteries.

How to check if a battery is charged?

Make sure your batteries are fully charged, first, and then check for the following: 1 Any cracks or dirt in the batteries. 2 The water-electrolyte levels (on a weekly basis). If the water runs too low, it can shorten the life of your batteries. Overfilling can also result in a loss of electrolytes. 3 Look for signs of corrosion on your connectors and ensure that they are tight. 4 Dirt and other debris can affect the performance of your batteries. Clean them regularly with a bristle brush, water, and baking soda, but take care not to get any of the electrical components wet.

What to check before checking batteries?

Make sure your batteries are fully charged, first, and then check for the following: Any cracks or dirt in the batteries. The water-electrolyte levels (on a weekly basis).

Why won't my golf cart move?

A Club Car golf cart will not move if power from the battery pack is not reaching the motor. Faulty parts such as the solenoid, OBC and wiring can also cause a golf cart to not move.

What to do if you don't get readings on golf cart?

If you are not getting these readings, change your batteries. You must keep in mind that there are differences between the various models of golf carts. Each model may have a different component and you have to be careful while handling them. Wrong handling can cause problems and the golf cart can get damaged.

How to know if a cart won't move?

When the cart won’t move, you have to be sure that the batteries are sending sufficient power to the circuit. You must check the fuse. Use the voltmeter to check the voltage at the key switch. In a cart with batteries rated at 48V, it must show 48V at the key switch.

How to check if a controller is corroded?

To check the controller, these are the steps: You will need a digital voltmeter (DVM) to check the 16-pin connector at the controller. Lift one wheel of the cart on a jack. The black probe from the DVM should be on the pack negative post.

How many batteries are in a golf cart?

Batteries: Some golf cart batteries are designed and structured in such a way that in a pack containing six batteries, #1, #2 and #3 will service the forward movement of the cart and #4, #5, #6 take over when the cart is reversed. So, if one of the batteries were to fail then the movement in that direction will be curtailed.

What happens if one of the batteries fails?

So, if one of the batteries were to fail then the movement in that direction will be curtailed. Checking individual batteries is very important to avoid such a situation. Controller: The design and functioning of the controller are similarly divided into forward and reverse movements of the golf cart.

Where is the Delphi fuse holder on a 2010 Club Car?

For this, the first place you must check is the main fuse. In the 2010 Club Car Precedent, the Delphi fuse holder is located near the solenoid. There are standard operating procedures to be followed while working on your golf cart. The Run/Tow switch must be on Tow and preferably you should disconnect the batteries.

Why won't my golf cart move?

Loose or corroded cable connections or a faulty controller can also cause the golf cart to not move. Malfunctioning microswitch. Faulty solenoid. Defective ignition switch. Loose or corroded cable connections. Faulty controller.

What happens if your golf cart battery doesn't charge?

Look out for a closed pedal switch that could be restricting the movement of the golf cart. When this is released, the cart will start moving properly .

Why won't my EZGO go forward?

The main reason why a EZGO gas golf cart will not go forward is because of a locked up brake, or a faulty solenoid and accelerator. A defective Run/Tow or Forward/Reverse switch can also cause a EZGO to not move forward. You can check out the steps given below to address this problem. Check if the brakes are performing as desired ...

What happens if a golf cart solenoid is defective?

When defective, the solenoid fails to transfer current from the battery to other parts of your golf cart.

How to check if ignition switch is working?

You can do this by hooking the wires present under the dash, connecting it to the battery, an ohmmeter, and check the reading. If you don’t get any reading, change the switch.

Is the Taylormade M4 driver adjustable?

Is the TaylorMade M4 driver adjustable? Yes, the TaylorMade M4 driver is adjustable. It’s possible to have twelve different options for the loft, lie angle and face angle, including the standard...

Is the Ping G25 adjustable?

Is the Ping G25 driver adjustable? The Ping G25 driver is adjustable. It’s possible to do four adjustments using the hosel adapter of the driver apart from the stated loft setting and...

How to reset a golf cart motor?

Reset the motor. Remove a panel in the rear of the golf cart using a screwdriver. When the motor is exposed, search for a small red button. Most often, the button is located where the wires enter the motor. If the button is sticking out, push it back in.

What to do if battery terminals are dirty?

If the terminals are dirty, purchase a battery terminal cleaner spray and use it on the terminals then try to start the motor. The cleaner spray is available at auto retail shops and in most automotive sections of chain retail stores.

Why do electric golf carts fail?

These carts can start to show signs of wear and may fail just like any other vehicle over time.

Why does my gas cart not work?

When you press down on the gas pedal and hear a tapping-like sound, this is the sound of the solenoid activating. When there is a disruption in the flow of the electrical current , your cart will not operate. A common reason for current disruption is solenoid wear.

What are the problems with electric golf carts?

These carts can start to show signs of wear and may fail just like any other vehicle over time. Learn about some of the more common issues associated with electric golf carts. 1. Solenoid Wear. The solenoid is the primary electrical switch in your golf cart and is designed to ensure the current from the battery flows into the motor. ...

What is the controller on a golf cart?

An electric golf carts' controller is known as the heart of the operation and closely resembles and operates much like the motherboard in a computer. So a problem with the controller will have rippling effects throughout the cart. A common function of the speed controller is to control the speed of the golf cart.

What happens if your cart doesn't move?

If the cart doesn't move in either direction, both switches have failed. Diagnosing a problem with the direction switches isn't a complicated matter, but repairing the switch is more complex, especially if the switches are built into the speed controller.

Why won't my sped controller accelerate?

Problems with the sped controller occur for a variety of reasons, but most often the cause is degradation due to age or lack of use.

How does a solenoid work?

Each time the solenoid activates as you press down on the gas pedal, the solenoid compounds down onto a thin metal contact plate. Over time, the force of this pressure creates tiny electric arcs on the plates' surface. These arcs eventually create a resistance that prevents the current from properly flowing.

Why won't my golf cart run after washing?

Washing a golf cart can damage the F/R switch or put holes in the battery casing causing the golf cart to stop working. Make sure to blow out excess water. Don’t get the F/R switch wet.

How to fix a club car that won't run after washing?

Make sure that the Club Car DS/Precedent golf cart completely dries out. Use an air blower to help the drying process . You can also use a fan for blowing on the engine compartment. It takes a few hours or a few days, even for the water to evaporate completely.

What to do if fuel is flooding?

To manage the widespread flooding of fuel, you can try replacing or adding new fuel to see if that helps. If that doesn’t help, then a damaged float pin or the wrong fuel level can be the problem. In that case, replace the pin and adjust the float bowl.

Can you power wash a golf cart battery?

No, it is usually advised not to power wash a golf cart battery. There are a few obvious reasons for it. The spray will be too hard on the battery for it to handle the pressure. Sensitive terminals, casing, and cables can get damaged easily. You can even puncture a hole into the casing of the cart’s battery, which is not what you want.

Can you wash a golf cart?

You can wash a golf cart, but you must be gentle and avoid exposing electrical wires to water. Power cleaning using a hose or jet, should be avoided. Remember to park your golf cart in a shaded location as sunlight can cause the soap to dry too fast. A golf cart’s exterior is covered with a layer of clear coating.

Can you drive a golf cart in the rain?

No, golf carts are not explicitly designed to drive in the rain. They tend to sink into the mud and sometimes even worse, like spinning out of control or sliding. After being in the rain, the cart won’t respond, and you’ll have to give it time to dry out. Do not let the golf carts sit in the rain for too long.

Can electric golf carts get wet?

Yes, electric golf carts can get wet. You can use water to clean your golf cart. But you must be cautious with the exposed parts and electrical parts. You do not want the vital parts of your cart to get wet. Golf carts can even run in wet conditions at times. They do come equipped with a roof and wipers.

Why is my Yamaha golf cart not moving?

The main cause of a Yamaha golf cart clicking but not moving, is a faulty controller or solenoid. The battery has to be checked first to see if it’s delivering the right voltage while in the idle state as well as when the pedal is pressed. There can be other reasons for the Yamaha golf cart not moving though you hear the click.

What to do if your G9 golf cart is not clicking?

If you find your G9 Yamaha golf cart not starting nor clicking, check the key components for damage. If you find the parts to in good condition, check the brushes in the starter/generator.

Why is my solenoid not clicking?

The reason why the solenoid is not clicking could be that it is faulty or has no grounding. Experts recommend checking all wiring and cable connections to rule out this possibility. Batteries on your G16 Yamaha golf carts should raise sufficient power to reach the solenoid and the starter/generator.

What is a faulty controller?

The controller is one major component that may have to be replaced. A faulty controller can stall the cart and the click you hear must be from the solenoid. Test the solenoid to see if it is functioning properly. You will require a multimeter, preferably a digital one, or a DVM for this.

How to check solenoid on G9 Yamaha?

The solenoid can be checked using an old screwdriver to jump the terminals. Your G9 Yamaha golf cart’s key must be in the start position. If the starter turns when you do this, your solenoid needs to be replaced. You must be careful while doing this crude test; there could be sparks when the two terminals touch.

Why do you need a wiring diagram?

A clear wiring diagram will help in ensuring that the cables are properly reconnected if you remove them for testing. In the solenoid, for example, the contacts inside can get jammed over a period. These have to be checked, cleaned, and re-fixed. If it still doesn’t work it has to be replaced.

What are the settings on the M3?

The variable settings on the M3 allow a player to adjust the loft, lie, and face angles of the club, as well as create a variable fade or draw bias. Which can correct many swing or hit issues...

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9