
The torque is 3.7 for 55 grams, 3.0 for 65 grams and 2.2 for 75 grams. Although this shaft is not made in a ladies flex, when there is one in other models the torque will be the highest of the five flexes. Because of the difference in torque between flexes, it also really becomes important to have the right flex for your club head speed.
Full Answer
How many degrees of torque should a golf shaft have?
A degree of 3 to 4 is normal for a steel shaft. Graphite shafts can have a lot more torque. Since graphite is not a solid piece of material, the torque can be much higher; to degrees of 7 or 8. When you have less torque in your club shaft, it is said that you will have a straighter shot and a stiffer feel.
How does torque affect shafts?
A high-torque shaft will twist more than a low-torque shaft. Put another way, some shafts resist twisting better than others. A shaft with a lower torque rating means the shaft better resists twisting; a shaft with a higher torque rating means the shaft is more prone to twisting (all other things being equal).
What is the torque of a graphite shaft?
So for most golfers, as long the torque of a graphite shaft is between 3.5 and 5.5 degrees - which is the case for the vast majority of graphite shafts today - the golfer will be OK and torque will never be a factor to worry about in the shaft fitting. Was this page helpful? Thanks for letting us know!
What is the difference between torque rating and shaft type?
A shaft with a lower torque rating means the shaft better resists twisting; a shaft with a higher torque rating means the shaft is more prone to twisting (all other things being equal). A golfer's swing, and the clubhead attached to the end of the shaft, exert forces on the shaft that lead to twisting.

How much torque do you need for screws?
US Recommended Bolt TorqueSizeRecommended TorqueGrade 218-8 S/S3/4"1251287/8"1291941"†18828713 more rows
Are all golf club torque wrenches the same?
You see, the wrenches from TaylorMade, Ping, Callaway, Titleist, Cobra, Mizuno and Nike all have the same head design, and the wrenches tend to use approximately the same torque rating (about 40 in./lb.). That means you can get away with adjusting all of these clubs with a single wrench.
How much torque can you apply with a screwdriver?
Manual torque screwdrivers can have a range of 0.04 N⋅m (6 in oz) to 20 N⋅m (170 in lb).
What is the torque to tighten the M6 screw?
Tightening torques - fasteners with hexagon and hexalobular socket and flat headsMaximum tightening torques (Nm)ISO 4026 / DIN 913 ISO 4027 / DIN 914 ISO 4028 / DIN 915Screw standardDIN 6912ISO 4029 / DIN 916M561.5M692.5M820512 more rows
How do you use a TaylorMade torque wrench?
0:362:09How to Adjust the TaylorMade M1 Driver - YouTubeYouTubeStart of suggested clipEnd of suggested clipSlide it down towards the bottom take the torque wrench provided my tailor-made tighten it back upMoreSlide it down towards the bottom take the torque wrench provided my tailor-made tighten it back up until you hear the click.
What size is TaylorMade tool?
4 x 4 x 0.75 inchesEnhance your purchaseBrandTaylorMadeItem Dimensions LxWxH4 x 4 x 0.75 inchesFinish TypeUnpolishedHead StyleTorxItem Torque1 Foot Pounds
Does longer screwdriver increase torque?
This may seam odd, but the different length of screwdriver really doesn't affect the torque directly. Torque is the force applied times the distance from the axis you are rotating about. So the torque of the screwdriver only really depends on the thinkness of the handle.
What torque is considered hand tight?
The hand tight torque value is the amount of torque required to turn a fastener by hand. This value is typically between 0.03 and 0.05 Nm for most applications.
How much torque can a human use by hand?
100N forceAverage human hand can apply 100N force easily.
How much torque can you put on a 6 mm bolt?
Typical maximum recommended thightening torques for metric bolts.Size (mm)Typical Maximum Tightening Torque (Nm)Property ClassM57.010.0M611.817.0M828.841.37 more rows
How do you determine tight torque?
DETERMINING TORQUE The general equation for bolt load based on applied torque is T = KFiDb where K = torque coefficient. K is a function of the coefficients of friction and collar friction in the joint, and these are based on variables such as surface finish, coatings, and so on.
What's the torque on a 6 mm bolt?
Metric Recommended Bolt TorqueBolt Diameter (mm)Recommended Torque (Nm)Class 8.8Class 10.961216830401055755 more rows
Can you mix golf club brands?
As consumers and golfers, we're free to pick and choose whatever clubs we want to round out a 14-club set. We can mix and match brands, models, types — there's no rule stating what kind of clubs we have to play. This means you're not only free to choose, but you also have to choose.
Are all golf clubs the same?
There are several different types of golf clubs in a typical golfer's bag. In fact, today, there are five categories of clubs: woods (including the driver), irons, hybrids, wedges and putters.
Is it OK to mix brands of golf clubs?
As a whole it is not only ok to have a mix of golf brands in your golf set but if done consciously it will ensure you have the best set of clubs for your swing.
Should your driver match your irons?
There is no requirement to match your driver with your woods. Brand, club head, shaft, weight and length are all parts which can match but golfers are best focusing on the combinations which deliver the best results for each club individually. The only exception is the grip which should be the same.
What is torque in golf?
Warren Little / Getty Images. "Torque" is a property of golf shafts that describes how much the shaft is prone to twisting during the golf swing. All shafts, steel and graphite, exhibit torque, which is measured in degrees. A high-torque shaft will twist more than a low-torque shaft. Put another way, some shafts resist twisting better than others.
What torque is needed for a graphite shaft?
So for most golfers, as long the torque of a graphite shaft is between 3.5 and 5.5 degrees - which is the case for the vast majority of graphite shafts today - the golfer will be OK and torque will never be a factor to worry about in the shaft fitting.
How Does Torque in Steel Shafts Compare to That in Graphite Shafts?
In steel shafts, because the type of steel material is the same throughout the entire shaft, the torque exists in a very narrow range of degrees, one that is much more narrow than in graphite shafts.
What does it mean when a shaft is high torque?
A high-torque shaft will twist more than a low-torque shaft. Put another way, some shafts resist twisting better than others. A shaft with a lower torque rating means the shaft better resists twisting; a shaft with a higher torque rating means the shaft is more prone to twisting (all other things being equal). ...
How much torque does graphite have?
This allows the torque in graphite shafts to range from as high as 7 or 8 degrees to as low as 1 degree, while in steel this range is only from a little more than 2 degrees to a little under 4 degrees.
What happens if you use too high a torque rating?
a strong golfer who uses shafts with too high a torque rating might produce shots that leak to the fade side;
What is twisting in golf?
A golfer's swing, and the clubhead attached to the end of the shaft, exert forces on the shaft that lead to twisting. This twisting is simply a part of the swing.
Which player will benefit from a lower torque shaft?
1) Players who tend to hook the ball will benefit from a lower torque shaft. Players who tend to slice the ball will benefit from a higher torque shaft.
How many shots does each golfer hit with each shaft?
Each golfer hit 10 shots with each shaft and the results were measured by our FlightScope X2 launch monitor. All testing was done at the range at The Bridges of Poplar Creek Country Club.
Why should you care about torque?
You should care because torque is a major component in how a shaft feels, much more than flex . You could have an XX-stiff shaft with high torque, and it might feel “smooth” or even “whippy.”. Alternately, you could have a senior flex shaft with low torque that can feel “boardy.”.
What is torque in a car?
Torque is really pretty simple: it’s the shaft’s resistance to twisting. Torque is measured in degrees (meaning: how many degrees will the shaft twist under a certain amount of force), and you’ll typically see measurements as low as 2° and as high as 5°, 6°, or 7°.
Does Tester 3 like low torque shafts?
Tester 3 hates boardy feeling shafts, so, despite the fact that his most-hated miss is a hook, he does not like low torque shafts. On the other hand, Tester 1 doesn’t like loose feeling shafts despite the fact that he needs all the help he can get to square the club face. Historically, he has found better success with lower torque shafts because he feels like he can release the club more aggressively.
Does torque affect where the ball ends up?
Torque also has a major impact on where the ball ends up. All other things being equal, a shaft with higher torque will lead to a club face that is pointed further left (for a RH golfer) at impact…but we know “all other things” are rarely equal when you add in the human element.
Is torque a rule?
Torque matters, and, like flex and weight , there are no easy rules to follow. You need to try a variety of things and be fit into the shaft that will work best for you.
What happens when you have less torque in your golf club shaft?
When you have more torque in your club shaft it is said that your shots can be less accurate but go further and have a nice soft feel.
Why is shaft torque important?
Shaft torque becomes increasingly important the faster you swing. Torque is the measure of how much the shaft twists during the golf swing. It may be hard to imagine this even happening, but shafts are made with that particular fact in mind. They are even made to resist it more or less, depending on your swing and what kind ...
Why does my golf club go faster?
This also means you can hit the ball a little further, because at the time the club strikes the ball the torque can cause the club head to go faster.
Why does a steel shaft have less torque?
A steel shaft will have less torque simply because of the material it is made of. A degree of 3 to 4 is normal for a steel shaft. Graphite shafts can have a lot more torque. Since graphite is not a solid piece of material, the torque can be much higher; to degrees of 7 or 8.
When you strike the ball, do you want your club head to be square?
When you strike the ball, you want your club head to be as square to your target as possible. When the club head twists, it can make the club head a degree or two open or closed when it makes contact. Therefore you want less torque when you are looking to straighten your ball flight.
Does Tiger Woods know how much torque he needs?
Certainly Tiger Woods knows exactly how much torque he needs for every club in his bag , but for a beginner it won't matter much. Torque should be one of the last things you look at when trying to improve your game. Golfweeks' Adam Woodard breaks down the results from the match.
What are wood screws made of?
Wood screws are usually made of brass, bronze, or other kinds of metal. Generally, steel screws are widely used for DIY craft -both interior and outdoor since they are available in different sizes, affordable, and strong.
How big are machine screws?
These screws are usually smaller than average screws and length ranges up to ¾ of an inch (19.05 mm). since these screws are designed to fasten existing holes,
What type of screws are used for mortar?
Masonry screws are the perfect choice for fastening materiel with concrete, mortar, or brick joints; however, you have to create a pilot hole before with a carbide bit and hammer drill. The two types of heads for masonry screws are flathead for countersinking and hex washer heads that sit on top of the material’s surface.
What is the shank on a screw?
Shank: shank is the smooth area of the fastener between head and thread. Depending on the type, some screws might not have any shank.
What is a slotted screw?
Slotted: slotted screws are the most common and simplest type screws with a single slot at the head. Although they are not compatible for heavy use, they are still around. The driver bits are usually measured by the width of the blade in inches like 1/16, 1/8, 1/4, 5/64, 3/16, 3/32, 5/32, 9/32.
Why are Phillips screws called Phillips screws?
Phillips: the Philips screws, which are named after Henry F. Phillips, was designed in such a way that so that the screwdriver comes out if too much torque is there. It is an intentional engineering point to protect the screws from breaking down that was introduced at the beginning of the 20th century.
What is stainless steel screw?
Stainless screws are designed to be used on many materials, including wood and sheet metal. Stainless screws are galvanized with a rust-resistant layer of zinc. The main advantage of this is it keeps these types of screws corrosion-free and perfect for both indoor and outdoor furniture, even for damp conditions; however, coating eventually wears off in case of outdoor use.
Ezgolfer
My buddy told me on the range today , to tighten my driver shaft by using the tool before every round . I was reluctant intially , however after using the tool was shocked that the driver head was more lively and felt heavy after tightening the screw.
Bodee
Haven't checked mine in two years. Haven't played all that much in that time either:- (
HackerD
I will start doing it. Used to carry an i-mix wrench as one time the head had come totally loose.
bruinsPATSirish
Very true statement, especially after hitting balls on the range with any of the adjustable headed clubs. I check mine quite frequently because they do get loose. Not sure performance wise the difference a tight screw makes, but I'm sure it doesn't hurt
Ezgolfer
Trust me on this .... I am a believer now . I casually neglected him when he told me intially.
dwboston
What if it's not obviously loose? Is it possible to overtighten these or does the torque screwdriver/tool prevent that?
Mathwiz
Granted the systems incorporate a torque limit, I don't just tighten initially when I check my clubs. I have noticed that after the click there is just a little more snugging going on. I back it off a little and then retighten until it "clicks".
What does torque mean in fasteners?
Unfortunate in the world of fasteners is the use of the word "torque" to describe how "tight" a fastener is twisted, as it risks the misconception, or misrepresentation, of what is being measured. Most would assume that the fastener, or base components, are actually being taken out of shape to some measured degree in relation to the value of "torque" being applied. That certainly can and does happen in the extreme as seen by anyone who twists off a fastener; or "pulls out the threads" by over tightening it; or has a fastener break later due to over stretching it. However that scenario is why we have recommended "torque" values for any given fastener; to greatly diminish, or prevent such occurance as going beyond the designed limits of the fastener itself. If a fastener is tightened between the recommended specifications of a high/low, or no more than a recommended high, then the fastener is in no danger of breaking and the clamping action produced is as required.
What is torque in engineering?
Torque by definition is something rotating, receiving power and/or applying power, ultimately generating a "load" upon a system to do "work". A common household use of the word "torque" is in the marketing strategy used to sell you a more powerful pickup truck.
Can you tighten action screws to 192 pounds?
Does this mean we all can safely tighten our action screws to 192 inch pounds? Of course not, because other factors come into play that lessen the allowable degree of "torque", such as the integrity of the base components being clamped; things already long ago determined by rifle manufacturer's, and stock makers.
Does heavy torque crush old glass?
The heavy torque will crush old glass bedding. The pillar bedding system has helped to eliminate this.

Use of Screws
Anatomy of A Screw
- Before diving into a dip, let’s have a look at the different parts of the screw that will help you to make any decision: Drive:drive is the mechanism of a screw that helps to install and remove the screws. The most commonly used drives shapes are the cross-head, square, star, slotted, and hex socket. Head:the head is the top of the screw that includes the drive. Different types of screw he…
Screws Common For Diy
- Wood Screws
wood screws are probably the most commonly used screws for DIY screws. Although it is known as wood screws, it is not made of screws. Rather they connect two-piece of wood. This type of screw has a semi-threaded shank and is available in different sizes and lengths with a sharp tip t… - Pocket Hole Screw
Pocket hole screws are the perfect choice for building furniture and cabinet. It requires a pre-drilled hole to fasten two pieces of wood. These holes hide the screws and are used with pocket hole jigs. They provide secure joints. This type of screw has a self-tapping tip, and pilot holes ar…
Type of Drive
- Slotted: slotted screws are the most common and simplest type screws with a single slot at the head. Although they are not compatible for heavy use, they are still around. The driver bits are usually measured by the width of the blade in inches like 1/16, 1/8, 1/4, 5/64, 3/16, 3/32, 5/32, and 9/32. Phillips: the Philips screws, which are named afte...
FAQ
- What kind of screws goes into wood? Wood screws are meticulously designed and made of metal and thus have a sharp tip that allows them to be pushed inside a wooden plank. Wood screws are usually made of brass, bronze, or other kinds of metal. Generally, steel screws are widely used for DIY craft -both interior and outdoor since they are available in different sizes, affordable, and str…
Closing Notes
- screws have an undeniable role in woodworking. Although many carpenters prefer to use adhesive, still now screws have their role, which can’t be replaced. There are lots of varieties available in the market, and it isn’t very clear to choose the right one. In the beginning, I promised to give you a general idea about the most commonly used screws, and I hope you have at least t…